Related Manuals for Barco MDPC-8127
Summary of Contents for Barco MDPC-8127
- Page 1 MDPC-8127 27” 8MP ultra-high definition digital pathology display User guide ENABLING BRIGHT OUTCOMES...
- Page 2 Barco NV Beneluxpark 21, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com Registered office: Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com...
-
Page 3: Table Of Contents
Power lock function..................................26 DPMS mode.......................................27 Hibernate ......................................27 Luminance target ....................................28 Color presets .....................................28 4.8.1 Color temperature...............................28 4.8.2 Color coordinates................................29 Color space ......................................29 4.10 Viewing modes ....................................29 4.11 Display functions .....................................30 4.12 sRGB ........................................30 4.13 Ambient Light Compensation (ALC).............................31 R5913216 /03 MDPC-8127... - Page 4 EDID timings......................................35 4.22 Display info ......................................36 4.23 Display status....................................36 5 Cleaning your display ..................................37 Cleaning instructions..................................38 6 Important information..................................39 Safety information...................................40 Cybersecurity ....................................41 Environmental information.................................41 EMC notice ......................................43 Explanation of symbols................................46 Legal disclaimer....................................49 Open source license information ............................50 R5913216 /03 MDPC-8127...
-
Page 5: Welcome
Welcome! R5913216 /03 MDPC-8127... -
Page 6: Regulatory Compliance Information
MDPC-8127. The display is not intended for use with digital images from frozen section, cytology, or non-formalin-fixed, paraffin embedded (non-FFPE) hematopathology specimens. -
Page 7: Technical Specifications
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC responsible: Barco Inc., 3059 Premiere Parkway Suite 400, 30097 Duluth GA, United States, Tel: +1 678 475 8000... - Page 8 EN 60601-1:2006 + A1:2013 + A12:2014 • ANSI/AAMI ES 60601-1:2005 + R1:2012 • CAN/CSA C22.2 No. 60601-1:2014 • EMI specific: • IEC 60601-1-2:2014 (ed.4) • EN 60601-1-2:2015 (ed.4) • FCC part 15 Class B • ICES-001 Level B • VCCI R5913216 /03 MDPC-8127...
-
Page 9: What's In The Box
• Cables for Mains, Video and USB If you ordered a Barco MXRT display controller, it is also in the box together with its accessories. A dedicated user guide is available on the documentation disc. Keep your original packaging. It is designed for this display and is the ideal protection during transport and storage. -
Page 10: Product Overview
7. Cable routing ducts 8. Stand locking mechanism 9. USB-B 2.0 upstream connector 10. DisplayPort IN 2 connector 11. DisplayPort IN 1 connector 12. Kensington security slot 13. 100–240 VAC mains power input and power switch Display Power Management System R5913216 /03 MDPC-8127... - Page 11 Welcome! Barco Touchpad The Barco Touchpad can control Barco’s Intuitive Workflow Tools and allows you to control digital pathology, enterprise imaging and other viewing applications with configurable multi-touch gestures and touchpad function activation buttons. Using the Barco Touchpad requires Barco’s MXRT display controller and driver to be installed on your workstation.
- Page 12 Welcome! R5913216 /03 MDPC-8127...
-
Page 13: Installation And Setup
Installation and setup Display controller installation ......................14 Display position adjustment ......................14 Cable connections ........................15 MXRT driver and Intuitive Workflow Tools installation ..............16 QAWeb Enterprise registration ......................16 VESA-mount installation .......................17 VESA-mount installation in portrait mode..................19 R5913216 /03 MDPC-8127... -
Page 14: Display Controller Installation
To adjust the height of the display, first move the slider at the back of the stand to the unlock position. Then you can raise or lower the display as desired. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support > Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices) -
Page 15: Cable Connections
If only one DisplayPort video input cable is connected the display will run at half of the specified refresh rate. Note: When two DisplayPort video inputs are connected you can easily switch between them in the OSD menu. See “Image source selection”, page 34 for more info. R5913216 /03 MDPC-8127... -
Page 16: Mxrt Driver And Intuitive Workflow Tools Installation
About When you are using a Barco MXRT display controller, you can start up your MDPC-8127 display system and install the MXRT driver and Intuitive Workflow Tools . Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details, improve focus during reading sessions, and accelerate workflow. -
Page 17: Vesa-Mount Installation
2. Put the display face down on a clean and soft horizontal surface. Be careful not to damage the panel screen. 3. Push the VESA mount cover to the right and lift the cover on the right with your finger or a flathead screwdriver. R5913216 /03 MDPC-8127... - Page 18 6. Unscrew the 4 fixation screws while supporting the stand. Image 2–10 7. Attach the panel firmly to the arm using 4 M4 screws. Respect the following rule to select an appropriate screw length: = T + W + 6.5 mm R5913216 /03 MDPC-8127...
-
Page 19: Vesa-Mount Installation In Portrait Mode
2.7 VESA-mount installation in portrait mode Introduction By default, your MDPC-8127 display is mounted in landscape position but it can also be used in portrait position. This section explains how to install and use the display in portrait orientation. Carefully follow the instructions hereafter to ensure proper product operation and to avoid physical damage to the product. - Page 20 Installation and setup R5913216 /03 MDPC-8127...
-
Page 21: Daily Operation
Daily operation R5913216 /03 MDPC-8127... -
Page 22: Recommendations For Daily Operation
Avoid objects on the Barco Touchpad When cables and other objects are left on the Barco Touchpad, these can be misinterpreted as fingers and may block DPMS and screen saver activation. Barco recommends keeping the Barco Touchpad clear of other objects. -
Page 23: Osd Menu Use
About the OSD menu The OSD menu allows you to configure your MDPC-8127 so that it will fit your needs in many possible working environments. You can also find information about the current status and settings in the OSD menu. - Page 24 Daily operation R5913216 /03 MDPC-8127...
-
Page 25: Advanced Operation
This section describes all settings available in the OSD menu and how to change and configure them. The factory default settings are optimized for reading digital pathology images with most diagnostic confidence. Barco highly recommends utilizing the following factory default settings when reading digital pathology images: •... -
Page 26: Osd Menu Language
About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your MDPC-8127. To change the language of the OSD menu: Bring up the OSD main menu. -
Page 27: Dpms Mode
By default, DPMS mode is enabled on your display, but it also needs to be activated on your workstation. To do this, go to the “Power options” of your workstation. Barco recommends setting DPMS activation after 20 minutes of non-usage. When DPMS mode is enabled, an additional power saving function becomes available: hibernate. -
Page 28: Luminance Target
4.7 Luminance target About the luminance target The luminance target of your MDPC-8127 is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. To set the luminance target: Bring up the OSD main menu. -
Page 29: Color Coordinates
• sRGB: A standard Red/Green/Blue color space that is most common for color monitors and is the default setting for the MDPC-8127. Note: This setting does not fully set your display to the sRGB color space. Refer to “sRGB”, page 30 to do this. -
Page 30: Display Functions
The sRGB color space combines a display function, color space and white point selection, and is commonly used in digital pathology and is the default setting for the MDPC-8127. Note: This setting does not fully set your display to the sRGB color space. Refer to “sRGB”, page 30... -
Page 31: Ambient Light Compensation (Alc)
Operating Room: Corresponds to light conditions in operating rooms. This setting has the highest maximum ambient light. To select a reading room: Bring up the OSD main menu. Navigate to the Configuration > Calibration > Ambient Light menu. Enter the Reading Room submenu. R5913216 /03 MDPC-8127... -
Page 32: Continuous Ambient Light Compensation (Alc)
OSD menu. The last results of both actions can be consulted from the OSD. When reading digital pathology images on the MDPC-8127, sRGB or Native are the recommended display functions. DICOM is an option, however this display function might be less relevant for your purposes. -
Page 33: Dicom Compliance Check
Pressing a key during calibration will abort the calibration, previous values will be restored. Note: After calibration, the compliance check will start automatically. 4.16.5 Reset DICOM calibration About reset DICOM calibration It is possible to restore the original (factory default) DICOM curve. R5913216 /03 MDPC-8127... -
Page 34: Dicom Error Threshold
4.18 Image source selection About image source selection The MDPC-8127 can have multiple image sources connected. Switching between the different sources can be done easily in the OSD menu. When two display port cables are connected and the image source selection is on automatic, then the full resolution and refresh rate are obtained. -
Page 35: Grayscale Conversion Modes
Select one of the available color conversion modes and confirm. 4.20 DisplayPort standard version About DisplayPort standard version The MDPC-8127 supports 2 DisplayPort standard versions: DP V1.1 and DP V1.2, the latter providing a higher video bandwidth. To select the DisplayPort standard version Bring up the OSD main menu. -
Page 36: Display Info
(display function, luminance, ALC, etc.). To retrieve the status of your display: Bring up the OSD main menu. Navigate to the Status menu. Enter the Display, Image Sources or Calibration submenu as desired. R5913216 /03 MDPC-8127... -
Page 37: Cleaning Your Display
Cleaning your display R5913216 /03 MDPC-8127... -
Page 38: Cleaning Instructions
Do not use sharp objects such as paperclips or tweezers to avoid damage to the LCD. CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics. Instead, apply the liquid to a cleaning cloth. R5913216 /03 MDPC-8127... -
Page 39: Important Information
Important information R5913216 /03 MDPC-8127... -
Page 40: Safety Information
Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them, paying particular attention to cords at plugs and receptacles. R5913216 /03 MDPC-8127... -
Page 41: Cybersecurity
6.2 Cybersecurity Hospital IT security To prevent unauthorized access to the device, the organization incorporating the MDPC-8127 in their IT network, shall have the necessary state of the art policies, processes, standards and other security measures in place to incorporate, support and protect a medical device into the IT network. This shall include the application of risk management (e.g. - Page 42 Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
-
Page 43: Emc Notice
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland. - Page 44 8127, including cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result. Electromagnetic emissions The MDPC-8127 is intended for use in the electromagnetic environment specified below. The customer or the user of the MDPC-8127 should assure that it is used in such an environment. Electromagnetic environment –...
- Page 45 704 – 787 LTE Band Pulse 13, 17 modulation 217 Hz 800 – 960 GSM 800/ Pulse 900, TETRA modulation 800, iDEN 18 Hz 820, CDMA 850, LTE Band 5 MDPC-8127 doesn’t contain susceptible components to magnetic fields R5913216 /03 MDPC-8127...
-
Page 46: Explanation Of Symbols
Indicates the device is approved according to the UL regulations for Canada and US Indicates the device is approved according to the UL regulations for Canada and US E352529 Indicates the device is approved according to the UL Demko regulations. Indicates the device is approved according to the CCC regulations. R5913216 /03 MDPC-8127... - Page 47 Indicates the DisplayPort connectors on the device. Indicates the legal manufacturer. Indicates the manufacturing date. Indicates the temperature limitations for the device to safely operate within specs. Values for xx and yy can be found in the technical specifications paragraph. R5913216 /03 MDPC-8127...
- Page 48 European WEEE (Waste Electrical and Electronic Equipment) directive. Indicates Direct Current (DC). Indicates Alternating Current (AC). Stand-by Equipotentiality Protective earth (ground) Symbols on the box On the box of the device, you may find the following symbols (nonrestrictive list): R5913216 /03 MDPC-8127...
-
Page 49: Legal Disclaimer
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized. -
Page 50: Open Source License Information
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide service, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever. - Page 52 Barco NV President Kennedypark 35 8500 Kortrijk Belgium R5913216 /03 | 2021-09-10 www.barco.com...