Related Manuals for Barco Nio Color 5MP
Summary of Contents for Barco Nio Color 5MP
- Page 1 Nio Color 5MP 5.8MP high-bright color display User Guide MDNC-6121 ENABLING BRIGHT OUTCOMES...
- Page 2 Barco NV Beneluxpark 21, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com Registered address: Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com...
-
Page 3: Table Of Contents
4.15 Embedded QA ....................................27 4.15.1 About Embedded QA..............................28 4.15.2 DICOM status report ..............................28 4.15.3 DICOM compliance check ............................29 4.15.4 DICOM calibration .................................29 4.15.5 Reset DICOM calibration............................29 4.15.6 DICOM error threshold ...............................29 4.16 Display orientation....................................30 4.17 Image scaling ......................................30 K5903146 /03 Nio Color 5MP... - Page 4 4.22 Display info ......................................33 4.23 Display status......................................33 5 Cleaning your display ....................................35 Cleaning instructions ..................................36 6 Important information....................................37 Safety information.....................................38 Environmental information................................39 Regulatory compliance information ............................41 EMC notice ......................................42 Explanation of symbols..................................44 Legal disclaimer....................................47 Technical specifications.................................47 K5903146 /03 Nio Color 5MP...
-
Page 5: Welcome
The Nio Color 5MP is also an excellent solution for radiologists who want to angle their desktop: it lets you choose your preferred viewing angle and offers a highly ergonomic display configuration. It’s also possible to switch between Clear base and Blue base viewing modes on-the-fly. - Page 6 Welcome! K5903146 /03 Nio Color 5MP...
-
Page 7: What's In The Box
• USB cable If you ordered a Barco display controller, it's also in the box together with its accessories. A dedicated user guide is available on the documentation disc. Keep your original packaging. It is designed for this display and is the ideal protection during transport and storage. - Page 8 Cable duct Foot lock clip Always connect the display(s) to a USB 3.0 hub, or if unavailable, to a USB 2.0 hub but then no more than two displays can be connected to the same hub. K5903146 /03 Nio Color 5MP...
-
Page 9: Installation
Installation Prior to installing your Nio Color 5MP and connecting all necessary cables, make sure to have a suitable display controller physically installed in your computer. If you are using a Barco display controller, please consult the user guide delivered with it to do this. -
Page 10: Display Position Adjustment
Image 2-2 WARNING: The display must be in its highest position before it can be properly pivoted. Store the foot lock clip in the storage hole in case the display needs to be transported later. K5903146 /03 Nio Color 5MP... -
Page 11: Cable Connections
Connect the workstation's USB host to the USB upstream connector on the display if you want to make use of QAWeb or any of the display USB downstream connectors (e.g. to connect a keyboard, mouse, touch pad or other peripheral). K5903146 /03 Nio Color 5MP... - Page 12 Image 2-8 Close the connector compartment cover. You will hear a “click” sound when the cover is in position. K5903146 /03 Nio Color 5MP...
-
Page 13: Vesa-Mount Installation
Put the display in the lowest position and lock the height mechanism. Image 2-10 Put the display face down on a clean and soft surface. Be careful not to damage the panel screen. Remove the plastic cover with a flathead screw driver. K5903146 /03 Nio Color 5MP... -
Page 14: First Time Starting Up
2.4 First time starting up Overview You are now ready to start up your Nio Color 5MP for the first time. Switch on your Nio Color 5MP as described in “Standby switching”, page 19. Turn on the computer connected to your display. - Page 15 Your Nio Color 5MP will be running in a basic video mode at a default refresh rate when first time starting up. If you are using a Barco display controller, please consult the user guide delivered with it to install the drivers, software and documentation.
- Page 16 Installation K5903146 /03 Nio Color 5MP...
-
Page 17: Daily Operation
Daily operation K5903146 /03 Nio Color 5MP... -
Page 18: Recommendations For Daily Operation
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels. -
Page 19: Standby Switching
How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Nio Color 5MP fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu. - Page 20 Exit all OSD menus at once by touching the standby key for approximately 2 seconds. The key icons are displayed above the keys, adapted to the function that it is used for (menu dependent). Overview key icons Left, Right Menu Enter Cancel Standby (IEC 60417–5009) K5903146 /03 Nio Color 5MP...
-
Page 21: Advanced Operation
Advanced operation K5903146 /03 Nio Color 5MP... -
Page 22: Osd Menu Language
About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages available for the OSD menu of your Nio Color 5MP. To change the language of the OSD menu: Bring up the OSD main menu. -
Page 23: Key Indicator Lights
About the power lock function By enabling the power lock function, the Nio Color 5MP is forced to remain switched on. This means that it can’t be switched to stand-by mode manually until the power lock function is disabled again. -
Page 24: Hibernate
4.8 Luminance target About the luminance target The luminance target of your Nio Color 5MP is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. To set the luminance target: Bring up the OSD main menu. -
Page 25: Viewing Modes
To quickly switch the viewing mode without having to enter the OSD menu, touch the left and right key at the same time during normal operation. The diagnostic mode should always be selected when the Nio Color 5MP is intended to be used in a diagnostic environment. -
Page 26: Color Presets
The American Association of Physicists in Medicine (AAPM) composed a list of pre-defined reading rooms. Each of these reading rooms are defined by following parameters: • the maximum light allowed in this type of room • the preset ambient light correction value for this reading room K5903146 /03 Nio Color 5MP... -
Page 27: Continuous Alc
DICOM display function when Ambient Light Compensation (ALC) is enabled. Please refer to “Ambient Light Compensation (ALC)”, page 26 to enable ALC. The available reading rooms for your Nio Color 5MP are: • CR/DR/ MAMMO: Corresponds to light conditions in diagnostic reading rooms for computed radiology, digital radiology or mammography. -
Page 28: About Embedded Qa
Embedded QA is not a replacement for the Barco MediCal QAWeb solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends MediCal QAWeb as the solution of choice for calibration and QA. Medical QAWeb brings... -
Page 29: Dicom Compliance Check
OK. To set the DICOM error threshold: Bring up the OSD main menu. Navigate to the Configuration > Calibration > Embedded QA menu. K5903146 /03 Nio Color 5MP... -
Page 30: Display Orientation
4.18 Image source selection About image source selection The Nio Color 5MP has 4 video inputs: DisplayPort 1, DVI 1, DisplayPort 2 and DVI 2. The input to be displayed is dependent on the selected image source selection mode: •... - Page 31 Enter the Left submenu and select one of the input channels. To select the image source on channel 1 and 2: Bring up the OSD main menu. Navigate to the Configuration > Image Sources menu. K5903146 /03 Nio Color 5MP...
-
Page 32: Grayscale Conversion Modes
Enter the Input 1 or Input 2 Image Source submenu and select one of the image sources. 4.19 Grayscale conversion modes Your Nio Color 5MP display automatically detects the connected video input signals and applies the correct grayscale conversion settings. Manually selecting a grayscale conversion mode is possible, but then your display’s image source selection mode should be set to allow this. -
Page 33: Display Info
(display function, luminance, ALC, etc.) and the status about activated connections. To retrieve the status of your display: Bring up the OSD main menu. Navigate to the Status menu. Enter the Display, Image Sources, Calibration or Connectivity submenu as desired. K5903146 /03 Nio Color 5MP... - Page 34 Advanced operation K5903146 /03 Nio Color 5MP...
-
Page 35: Cleaning Your Display
Cleaning your display K5903146 /03 Nio Color 5MP... -
Page 36: Cleaning Instructions
LCD. CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics. Instead, apply the liquid to a cleaning cloth. K5903146 /03 Nio Color 5MP... -
Page 37: Important Information
Important information K5903146 /03 Nio Color 5MP... -
Page 38: Safety Information
• The installer shall assess the magnetic environment before installation or use of the device. Power cords: • Do not overload wall outlets and extension cords as this may result in fire or electric shock. K5903146 /03 Nio Color 5MP... -
Page 39: Environmental Information
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. K5903146 /03 Nio Color 5MP... - Page 40 Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
-
Page 41: Regulatory Compliance Information
The manufacturing country of the product is indicated on the product label (“Made in …”). Importers contact information To find your local importer, contact one of Barco’s regional offices via the contact information provided on our website (www.barco.com). FCC class B This device complies with Part 15 of the FCC Rules. -
Page 42: Emc Notice
Electromagnetic emissions The Nio Color 5MP is intended for use in the electromagnetic environment specified below. The customer or the user of the Nio Color 5MP should assure that it is used in such an environment. - Page 43 430 – 470 GMRS 460, FM ± 5 kHz FRS 460 deviation 1 kHz sine 704 – 787 LTE Band Pulse 13, 17 modulation 217 Hz Nio Color 5MP doesn’t contain susceptible components to magnetic fields K5903146 /03 Nio Color 5MP...
-
Page 44: Explanation Of Symbols
Indicates the device is approved according to the UL regulations for Canada and US E352529 Indicates the device is approved according to the UL Demko regulations Indicates the device is approved according to the CCC regulations K5903146 /03 Nio Color 5MP... - Page 45 Indicates the device serial number Indicates the device part number or catalogue number Warning: dangerous voltage Caution Consult the operating instructions Values for xx and yy can be found in the technical specifications paragraph. K5903146 /03 Nio Color 5MP...
- Page 46 Indicates the range of humidity to which the medical device can be safely exposed when being stored. Indicates the range of atmospheric pressure to which the medical device can be safely 106 kPa exposed when being stored. 50 kPa K5903146 /03 Nio Color 5MP...
-
Page 47: Legal Disclaimer
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized. - Page 48 Tilt -10° to +30° Swivel -45° to +45° Pivot 90° Height adjustment range 100 mm Mounting standard VESA (100 mm) Screen protection Protective, anti-reflective glass cover (optional) Recommended modalities All digital images, including digital mammography K5903146 /03 Nio Color 5MP...
- Page 49 0 °C to 40 °C (15 °C to 35 °C within specs) Storage temperature -20 °C to 60 °C Operating humidity 8% to 80% (non-condensing) Storage humidity 5% to 85% (non-condensing) Operating pressure 70 kPa minimum Storage pressure 50 to 106 kPa K5903146 /03 Nio Color 5MP...
- Page 50 Barco NV President Kennedypark 35 8500 Kortrijk Belgium K5903146 /03 | 2018-11-12 Barco NV | Beneluxpark 21, 8500 Kortrijk, Belgium Registered address: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com...