Page 1
MX1212 Bare Pump Assemblies Models: MX1212PL (PTFE/LEATHER CHEVRONS), MX1212PP (PTFE CHEVRONS), MX1212PU (PTFE/UHMW CHEVRONS), MX1212UC (U-CUPS) Patent 7,603,855 AX85S Air Motor Assembly FX12 Fluid Pump Assembly pages 8-14 pages 15-22 Air inlet 606mm 8 " Air inlet Air inlet 606mm 606mm 8 "...
Page 2
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT. FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300). 77-2916-EU...
2. Periodically inspect all hoses for leaks parts in the pump. Consult your BINKS 2. Make sure the pump is grounded. and/or abrasions and tighten all representative for pump materials of NEVER operate the unit when it is on connections before use.
Page 4
5. User shall ensure all metallic parts of the equipment are suitably bonded to earth. Should be no greater than 1 . EC Declaration of Conformity Binks, Ringwood Road, Bournemouth, BH11 9LH, UK As the manufacturer of the items listed below: Piston Pumps MX412 & MX432 MX1212 &...
Page 5
MX1212 BARE PUMP ASSEMBLIES GROUND WIRE ITEM MX1212PL MX1212PP MX1212PU MX1212UC PART NUMBER DESCRIPTION QTY. QTY. QTY. QTY. AX85S AX85S AIR MOTOR ASSEMBLY FX12PL FX12 FLUID SECTION ASSEMBLY (PTFE/LEATHER) – – – FX12PP FX12 FLUID SECTION ASSEMBLY (PTFE) – –...
Page 6
MX1212 BARE PUMP ASSEMBLIES – MAINTENANCE 7.9 - 8.5 Nm [70 - 75 in-lbs] 11mm 7.9 - 8.5 Nm [70 - 75 in-lbs] 20mm MAINTENANCE SYMBOLS ITEM NUMBER MAINTENANCE ORDER (Reverse for assembly) PETROLEUM JELLY THREAD SEALANT (PTFE tape) 77-2916-EU page 6 of 24...
Page 7
MX1212 BARE PUMP ASSEMBLIES – TROUBLESHOOTING PROBLEM CAUSE SOLUTION Pump will not start No compressed air. Check compressed air supply. Spray tip is blocked. Clean or replace the spray tip. Erratic operation of air Worn poppet assemblies. Replace the poppet assemblies. motor, air motor stops Worn or dirty spool and sleeve Clean or replace the spool and sleeve...
AX85S Air Motor Assembly Patent 7,603,855 SPECIFICATIONS Maximum air inlet pressure: 8 bar [116 psi] Maximimum recommended 20 cycles/min continuous cycle rate: Air inlet connection: 3/8" BSP(f) Piston Diameter: 85 mm [3.3 in] Stroke Length: 75 mm [3.0 in] 77-2916-EU page 8 of 24...
AX85S AIR MOTOR ASSEMBLY MAINTENANCE SYMBOLS ITEM NUMBER DISASSEMBLY ORDER (Reverse order for assembly) PETROLEUM JELLY/GREASE THREAD SEALANT (PTFE tape) • Parts are included in 0115-010215 AX85 Repair Kit. ◊ Parts are included in 0115-010217 AX85 Seal Kit. N Parts are included in 0115-010226 Air Motor Valve Repair Kit. ∆...
Page 10
AX85S AIR MOTOR ASSEMBLY ITEM PART NUMBER DESCRIPTION QTY. 0115-010023 EXHAUST COVER SCREEN ❍ 0115-010022 EXHAUST COVER ❍ 0115-010026 BUTTON HEAD CAP SCREW ❍s 0115-010073 BUTTON HEAD CAP SCREW ❍s 0115-010019 QUICK EXHAUST VALVE CAGE ❍ 0115-010021 O-RING +§N ❍ 0115-010020 DIAPHRAGM ❍...
Page 11
AX85S AIR MOTOR ASSEMBLY – MAINTENANCE MAINTENANCE SYMBOLS ITEM NUMBER DISASSEMBLY ORDER (Reverse order for assembly) PETROLEUM JELLY/ GREASE THREAD SEALANT (PTFE tape) 77-2916-EU page 11 of 24...
Page 12
AX85S AIR MOTOR ASSEMBLY – MAINTENANCE 8.5 Nm [75 in-lb] Max MAINTENANCE SYMBOLS ITEM NUMBER DISASSEMBLY ORDER (Reverse order for assembly) PETROLEUM JELLY/GREASE THREAD SEALANT (PTFE tape) 77-2916-EU page 12 of 24...
Page 13
AX85S AIR MOTOR ASSEMBLY – MAINTENANCE 12.4 - 13.6 Nm [110 - 120 in-lb] MAINTENANCE SYMBOLS ITEM NUMBER DISASSEMBLY ORDER (Reverse order for assembly) PETROLEUM JELLY/GREASE THREAD SEALANT (PTFE tape) DANGER You are in the presence of magnetic fields which may interfere with the operation of certain pacemakers.
Page 14
AX85SE AIR MOTOR ASSEMBLY – TROUBLESHOOTING PROBLEM CAUSE SOLUTION Pump will not start No compressed air. Check compressed air supply. System is blocked. Clear the blockage. Erratic operation of air Worn poppet assemblies. Replace poppet assemblies. motor, air motor stops Worn or dirty spool and sleeve Clean or replace the spool and sleeve assembly.
Page 15
FX12 Fluid Pump Assemblies Models: FX12PL (PTFE/Leather), FX12PP (PTFE), FX121PU (PTFE/U-Cups), FX12UC (U-Cups) SPECIFICATIONS Maximum fluid pressure: 96 bar [1390 psi] Displacement per cycle: 72 cc [2.4 oz] Output @ 60 cycles/min: 4.3 L /m [1.1 gal/m] Fluid inlet size: 3/4"...
Page 16
FX12 FLUID PUMP ASSEMBLIES (CHEVRON PACKINGS) Models: FX12PL (PTFE/Leather), FX12PP (PTFE), FX12PU (PTFE/UHMW) • Parts are included in Repair Kits + Parts are included in Seal Kits 0115-010269 FX12 CHECK VALVE ASSEMBLY MAINTENANCE SYMBOLS ITEM NUMBER MAINTENANCE ORDER (Reverse for assembly) PETROLEUM JELLY THREAD SEALANT (PTFE tape)
Page 18
FX12 FLUID PUMP ASSEMBLIES (U-CUPS) Model: FX12UC • Parts are included in 0115-010305 Repair Kit + Parts are included in 0115-010304 Seal Kit 0115-010269 MAINTENANCE SYMBOLS FX12 CHECK VALVE ASSEMBLY ITEM NUMBER DISASSEMBLY ORDER (Reverse order for assembly) PETROLEUM JELLY /GREASE THREAD SEALANT (PTFE tape) 77-2916-EU...
Page 20
FX12 FLUID PUMP (CHEVRONS) – MAINTENANCE Models: FX12PL (PTFE/Leather), FX12PP (PTFE), FX12PU (PTFE/UHMW) MAINTENANCE SYMBOLS MAINTENANCE ORDER (Reverse for assembly) PETROLEUM JELLY THREAD SEALANT (PTFE tape) UHMW (2x) UHMW (2x) if applicable if applicable 77-2916-EU page 20 of 24...
Page 21
FX12 FLUID PUMP (U-CUPS) – MAINTENANCE Model: FX12UC MAINTENANCE SYMBOLS MAINTENANCE ORDER (Reverse for assembly) PETROLEUM JELLY THREAD SEALANT (PTFE tape) 77-2916-EU page 21 of 24...
Page 22
FX12 FLUID PUMP ASSEMBLIES – TROUBLESHOOTING PROBLEM CAUSE SOLUTION Material in solvent cup Worn or dirty upper packings. Replace or clean upper packings as necessary. Pump does not stop on the Worn or dirty lower ball check. Replace or clean the parts as necessary. down stroke Pump does not stop on the Worn or dirty upper ball check.
Page 23
ACCESSORIES FOR YOUR MX1212 BARE PUMP TROLLEY ASSEMBLY FLUID FILTER (100 MESH) BRACKET 0115-010186 0110-009130 0115-010179 Service Bulletin 77-2925 Service Bulletin 77-2925 SIPHON KITS AIR CONTROLS LUBRICATING OIL FOR 0115-010236 20 L (20 MESH) 0115-010180 (Air Assist) FX-12 FLUID PUMP 0115-010381 200 L (30 MESH) 0115-010198 (Airless) 0114-009433...
This product is covered by Binks’ 5 Year Limited Warranty. Binks European Sales and Service Listing: www.finishingbrands.eu Binks Binks has authorized distributors throughout the world. For technical assistance or the distributor nearest you, see listing below. Finishing Brands UK Correspondence address:...