Advertisement

Quick Links

Receiving instructions:
After delivery, IMMEDIATELY remove the packaging from the product. Inspect the product closely to determine
whether it sustained damage during transport. If damage is discovered, record a complete description of the damage
on the bill of lading and notify the freight carrier. If the product is undamaged, discard the packaging.
NOTICES:
1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the
product is used is the responsibility of the end-user.
2) VESTIL is not liable for any injury or property damage resulting from failure to apply either:
a) Instructions in this manual; or
b) Information provided on labels affixed to the product.
3) Vestil is not responsible for consequential damages sustained while assembling, using, or maintaining this
product.

Table of Contents

Jib specifications.................................................................................................................................2
Signal words...................................................................................................................................... 2
Safe use recommendations................................................................................................................... 2 - 3
Function tests.................................................................................................................................... 3
FIGS. 1-4: Exploded parts diagrams and bills of materials........................................................................... 3 - 5
Assembly instructions.......................................................................................................................... 5 - 6
Use instructions..................................................................................................................................7
Inspections & Maintenance................................................................................................................... 8 - 9
Labeling diagram................................................................................................................................ 9
Limited warranty................................................................................................................................. 10
Copyright 2016 Vestil Manufacturing Co.
Rev. 10/17/2016
V
ESTIL
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
www.vestilmfg.com
JIB-HC-Series Jib Cranes
Instruction Manual
JIB-HC, MANUAL
M
ANUFACTURING
Fax: (260) 665-1339
e-mail:
s ales@vestil.com
H U
C
.
ORP
U
Page 1 of 10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JIB-HC-Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vestil JIB-HC-Series

  • Page 1: Table Of Contents

    1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the product is used is the responsibility of the end-user. 2) VESTIL is not liable for any injury or property damage resulting from failure to apply either: a) Instructions in this manual; or b) Information provided on labels affixed to the product.
  • Page 2: Jib Specifications

     DO NOT use a damaged or malfunctioning jib! Restore the crane to normal operating condition before returning it to service. Copyright 2016 Vestil Manufacturing Co. Page 2 of 10...
  • Page 3: Function Tests

     DO NOT use the crane if any label is unreadable, damaged, or missing (see “Labeling diagram” on p. 9). Contact Vestil for replacement labels whenever necessary.  DO NOT modify the crane! Modifications automatically void the limited warranty (see p. 10) and might make the crane unsafe to use.
  • Page 4 ” SAE flat washer, zinc-plated 37048 Nylock nut, zinc-plated, 1 ” – 7, grade 2 65078 Extended prong cotter pin, zinc finish, ” x 1 ” 36266 ” – 20, hex jam nut, zinc-plated Copyright 2016 Vestil Manufacturing Co. Page 4 of 10...
  • Page 5: Assembly Instructions

    NOTE: Position the Steel column axles so that equal numbers of thread Flat washer (33098) ” stick out above and ” on either side of Lock nut (37048) below the brackets. center line) Copyright 2016 Vestil Manufacturing Co. Page 5 of 10...
  • Page 6 Jam nut (36266 or 28-145-003) 36260) Mounting tab Cotter pin Mounting tab Clevis pin Mounting tab Clevis pin Yoke Jam nut Cotter pin (bend the arms of the cotter pin around the clevis pin) Copyright 2016 Vestil Manufacturing Co. Page 6 of 10...
  • Page 7: Use Instructions

    Connect the load to the hoist chain/cable, using appropriate rigging. Then, raise the load only as high as necessary. Slowly direct the load to the desired location. Once the I-beam and hoist are properly centered above the work location, lower the load and disconnect it from the hoist. Copyright 2016 Vestil Manufacturing Co. Page 7 of 10...
  • Page 8: Inspections & Maintenance

     A crane which has been idle for a period of over 6 months shall be given a “Complete inspection” before placing in service.  Standby cranes shall be given a “Frequent inspection” at least semi-annually (twice per year; 1 inspection each 6 months). Copyright 2016 Vestil Manufacturing Co. Page 8 of 10...
  • Page 9: Labeling Diagram

    B: Label 560, 561, or 562 (both sides of jib; applied to black rectangle of label 391) C: Label 586 (on other side of jib) – Hazards of use D: Label 287 – Product data label. Copyright 2016 Vestil Manufacturing Co. Page 9 of 10...
  • Page 10: Limited Warranty

    (you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid.

This manual is also suitable for:

Jib-hc-3Jib-hc-6Jib-hc-10Jib-hc-20

Table of Contents