Download Print this page
Vestil JIB-HC Owner's Manual

Vestil JIB-HC Owner's Manual

Tie rod, wall & floor mounted jibs

Advertisement

Quick Links

Vestil Manufacturing Company
2999 N. Wayne Street, P.O. Box 507
Angola, IN 46703 USA
Phone (260) 665-7586 • Fax (260) 665-1339
sales@vestil.com • www.vestil.com
Contents
Warnings and Safety Instructions.................... 1
Receiving Instructions ..................................... 1
Warranty .......................................................... 1
Inspection Instructions .................................... 2
JIB-HC Installation Instructions ....................... 3
WARNINGS & SAFETY INSTRUCTIONS
Read owner's manual completely before operating unit!
• Keep clear when operating.
• Never go under unit if there is weight on unit.
• Remove weight before working on unit.
• Always inspect unit before each use.
• Never use if unit is damaged.
• Never lift more than the rated capacity.
• Never mount unit near electrical lines.
• When mounting this unit be sure supporting surface
is sufficient.
• Make sure all operator safety labels are in place.
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected
prior to shipment. However, it is possible that the
unit may incur damage during transit. If you see
damage when unloading make a note of it on the
SHIPPER RECEIVER.
Remove all packing and strapping material,
inspect for damage. IF DAMAGE IS EVIDENT,
FILE
A
CLAIM
IMMEDIATELY! Also, check the platform size, type
of power unit, etc., to see that the unit is correct for
the intended application.
WITH
THE
CARRIER
Revised 09-10
A company dedicated to solving ergonomic and material
handling problems since 1955.
OWNER'S
MANUAL
TIE ROD, WALL & FLOOR MOUNTED JIBS
Model JIB-HC, JIB-LC, JIB-FM
JIB-LC Installation Instructions ........................ 4
JIB-FM Installation Instructions ..................... 5-9
Labeling diagrams .......................................... 10
Limited Warranty............................................. 11
WARRANTY
This product is warranted for 90 DAYS from
date of purchase to be free of manufacturing defects
in material and workmanship. The manufacturer's
obligation hereunder is limited to repairing such
products during the warranty period, provided the
product is sent prepaid back to the factory.
This warranty does not cover normal wear of
parts or damage resulting from any of the following:
negligent use or misuse of the product, use or
application contrary to
installation instructions, or disassembly, repair or
alteration by any person prior to authorization from
a factory representative.
JIB-HC
TIE ROD, WALL & FLOOR MOUNTED JIBS
JIB-FM
JIB-LC
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the JIB-HC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vestil JIB-HC

  • Page 1 Receiving Instructions ........1 Labeling diagrams .......... 10 Warranty ............1 Limited Warranty..........11 Inspection Instructions ........2 JIB-HC Installation Instructions ....... 3 WARRANTY WARNINGS & SAFETY INSTRUCTIONS This product is warranted for 90 DAYS from Read owner's manual completely before operating unit! date of purchase to be free of manufacturing defects •...
  • Page 2: Inspection Instructions

    INSPECTION INSTRUCTIONS Per OSHA Regulations 1910.179 all gantry cranes/jibs should have an: 1910.179(j)(1)(i) Initial inspection - Prior to initial use all new and altered cranes shall be inspected to insure compliance. Besides that, for gantry cranes in regular service, there are two general classifications of inspections based upon the intervals at which the inspection should be performed.
  • Page 3 TIE ROD JIB ( FOR HIGH CEILINGS Model JIB-HC-3-89, JIB-HC-6-89, JIB-HC-10-89 & JIB-HC-20-89 1-11/16" 1-11/16" BOOM ASSEMBLY, UPPER SUPPORT ASSEMBLY & TIE ROD ASSEMBLY FOR HIGH CEILING JIBS (SHIPPED IN 3 SECTIONS) 1) Drill holes at desired height on a steel column using the dimensions as shown.
  • Page 4 WALL JIB ( FOR LOW CEILINGS Model JIB-LC-3-92, JIB-LC-6-92, JIB-LC-10-92 & JIB-LC-20-92 1-11/16" LOW CEILING JIB CRANE IS SHIPPED IN 2 SECTIONS, FRAME ASSEMBLY & PIVOT BRACKETS 1-11/16" 1) Drill holes at desired height on a steel column using the dimensions as shown.
  • Page 5: Specifications

    FLOOR MOUNTED JIBS Model JIB-FM-3-80 ROLLER JIB CRANE IS SHIPPED IN 3 SECTIONS, HEAD ASSEMBLY, BEARING BOOM ASSEMBLY, MAST ASSEMBLY, AND A BOX CONE MAST CONTAINING BOLTS AND INSTRUCTIONS ASSEMBLY 1) After foundation has hardened with anchor bolts set, install leveling nuts (jam nuts) on anchor bolts and level across nuts.
  • Page 6 FLOOR MOUNTED JIBS Model JIB-FM-6-80 ROLLER JIB CRANE IS SHIPPED IN 3 SECTIONS, HEAD ASSEMBLY, BEARING BOOM ASSEMBLY, MAST ASSEMBLY, AND A BOX CONE MAST CONTAINING BOLTS AND INSTRUCTIONS ASSEMBLY 1) After foundation has hardened with anchor bolts set, install leveling nuts (jam nuts) on anchor bolts and level across nuts.
  • Page 7 FLOOR MOUNTED JIBS Model JIB-FM-10-80 ROLLER JIB CRANE IS SHIPPED IN 3 SECTIONS, HEAD ASSEMBLY, BEARING BOOM ASSEMBLY, MAST ASSEMBLY, AND A BOX CONE MAST CONTAINING BOLTS AND INSTRUCTIONS ASSEMBLY 1) After foundation has hardened with anchor bolts set, install leveling nuts (jam nuts) on anchor bolts and level across nuts.
  • Page 8 FLOOR MOUNTED JIBS Model JIB-FM-20-80 ROLLER JIB CRANE IS SHIPPED IN 3 SECTIONS, HEAD ASSEMBLY, BEARING BOOM ASSEMBLY, MAST ASSEMBLY, AND A BOX CONE MAST CONTAINING BOLTS AND INSTRUCTIONS ASSEMBLY 1) After foundation has hardened with anchor bolts set, install leveling nuts (jam nuts) on anchor bolts and level across nuts.
  • Page 9 FLOOR MOUNTED JIBS Model JIB-FM-40-80 ROLLER JIB CRANE IS SHIPPED IN 3 SECTIONS, HEAD ASSEMBLY, BEARING BOOM ASSEMBLY, MAST ASSEMBLY, AND A BOX CONE MAST CONTAINING BOLTS AND INSTRUCTIONS ASSEMBLY 1) After foundation has hardened with anchor bolts set, install leveling nuts (jam nuts) on anchor bolts and level across nuts.
  • Page 10   A: Label 391 + 562, 561, 560, 397, or 398 JIB-FM:   Label 561: Label 562:   Label 560: Label 397:   Label 398: B: Label 586 C: Label 287   JIB-HC: JIB-LC: A (on opposite side of beam)
  • Page 11: Limited Warranty

    (you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid. What is an “original part”? An original part is a part used to make the product as shipped to the warrantee.

This manual is also suitable for:

Jib-fmJib-lc