Page 1
Mini Round Baler SRB-870 Owner’s Manual 10/12/21...
Page 2
Mini Round Baler SRB-870 Page left blank intentionally...
Page 3
Mini Round Baler SRB-870 TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Tar River dealer. Read manual in- structions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Owner’s/Operator’s Manual are completed before releasing equipment to the owner.
Mini Round Baler SRB-870 Table of Contents Introduction …………………………………………………………………………………………….. 5 Technical Specifications ……………………………………………………………………………….. 5 Safety …………………………………………………………………………………………………… 6 Safety Signal Words ……………………………………………………………………………………. 6 General Safety Guidelines ……………………………………………………………………………… 7 Safety Decal Care ………………………………………………………………………………………. 7 Before Operation ……………………………………………………………………………………….. 8 During Operation ……………………………………………………………………………………….. 9 Highway And Transport Operations ……………………………………………………………………...
Mini Round Baler SRB-870 Important Safety Information Safety It is important that you read the entire manual and to become familiar with this product before you begin using it. This product is designed for certain applications only. The manufacturer cannot be responsible for issues arising from modification.
Mini Round Baler SRB-870 Important Safety Information General Safety Guidelines Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. De- signers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
Mini Round Baler SRB-870 Important Safety Information How to install Safety Signs: Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper.
Mini Round Baler SRB-870 Important Safety Information During Operation Children should not be allowed on the machine. • Clear the area of small children and bystanders before moving the machine. • If using a towing unit, securely attach feeder by using a hardened 3/4” pin, a metal retainer, and safety •...
Mini Round Baler SRB-870 Important Safety Information Highway and Transport Operations Adopt safe driving practices. • Keep the brake pedals latched together at all times. Never use independent braking with machine in tow • as loss of control and/or upset of unit can result.
Page 10
Mini Round Baler SRB-870 Important Safety Information Highway and Transport Operations Maneuver the tractor or towing vehicle at safe speeds. • Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or death. • Avoid loose fill, rocks and holes, they can be dangerous for equipment operation or movement.
Mini Round Baler SRB-870 Assembly The PTO shaft, twine and electrical connections are located in the twine storage compartment (under the lid at front of the baler). The wheels are located inside the bale opener door (at rear of the baler). See “Attaching Wheels”...
Page 12
Mini Round Baler SRB-870 Assembly Attaching wheels: The baler wheels are stored inside the baler rolling chamber at the rear of the baler for shipping purposes. The rear door is opened by the baler hydraulics. Opening rear door: Press and hold the red button on the controller to activate the hydraulic cylinder to raise the door. Cau- •...
Page 13
Mini Round Baler SRB-870 Assembly Attaching wheels: Remove the wheels from the baling chamber, unlock the flow control valve and close the rear door. Cau- • tion: Before closing the rear door make sure no one is standing near the rear of the baler.
Page 14
Mini Round Baler SRB-870 Assembly Attaching the PTO shaft: Before installing the PTO shaft make sure that the RPM rating and the direction of rotation match those of the tractor. Carefully read the PTO shaft and tractor instructions. Before operation, make sure that the guards are installed on the power take off of the tractor and PTO shaft.
Page 15
Mini Round Baler SRB-870 Assembly Threading the twine: The twine is located in the twine storage compartment of the baler (located in the front of the baler). This baler can handle up to two rolls of twine at a time.
Page 16
Mini Round Baler SRB-870 Assembly Step 3: Once the twine is thru the RH storage compartment wall, feed twine thru the tensioner and front twine guide. Wrap the twine around the pulley once as shown in the small or large slot depending on application. See “Bale Density”...
Mini Round Baler SRB-870 Operating Instructions Initial Preparation for Baling: The pick-up handle must be moved to the “Operation” position prior to baling. This will lower the pick-up. Pull down on handle, move the latch to the right and allow the handle to move up. NOTE: Only lower the pick -up when ready to begin baling.
Page 18
Mini Round Baler SRB-870 Operating Instructions Baling: Line up tractor with the first windrow. Engage the tractor’s PTO and begin baling. • Slowly drive over the windrow. It is recommended to drive the tractor 2-3 miles per hour for best results.
Mini Round Baler SRB-870 Adjustments Bale Density: Adjust bale density according to the tractor size, field conditions and type of material baled. • To change positions of the Connecting Rod, remove the hairpin clip and move to next hole up or down.
Page 20
Mini Round Baler SRB-870 Adjustments Number of Wraps per Bale: The number of wraps per bale is controlled by the pulley located under the front RH side cover of the ma- • chine. There are two positions on the pulley. The large slot will wrap the bale approximately 11 times. The small •...
Page 21
Mini Round Baler SRB-870 Adjustments Rear Door Closing Rate: If the flow control valve handle is parallel to the control valve body it is fully open. There is no restriction • of flow. Note: In the fully open position, the rear door will close rapidly. Anyone standing under or near the door could be seriously injured.
Page 22
Mini Round Baler SRB-870 Adjustments After Operation: Follow the guidelines listed below after baling. Store the baler under a shelter or in a building out of the weather. • If left attached to the tractor, lower the baler so that the wheels are touching the ground. Never leave any •...
Page 23
Mini Round Baler SRB-870 Adjustments Roller Chain: Roller chains will stretch during normal usage, especially during initial use of the baler. This is normal for any type of roller chain and is to be expected. Performing regular maintenance will extend the life of the chains and sprockets.
Page 24
Mini Round Baler SRB-870 Adjustments Roller Chain continued: Pick-up drive chain Remove pick-up drive cover by removing the (3) threaded knobs. Adjust the pick-up drive chain tension by changing the position of the tension pulley. Chain deflection should be set at approximately 1/8”.
Page 25
Mini Round Baler SRB-870 Adjustments Pick-up Suspension: The pick-up suspension is supported by springs on both sides of the baler. Check the spring with the pick-up in the working position. The correct length of the spring is 1-7/8”. Be sure to check both springs. Adjustment to the springs is made by loosening or tightening the nuts on the rod.
Page 26
Mini Round Baler SRB-870 Adjustments Twine Cutting Blade: Replace the blade as needed. Loosen the hardware holding the blade. Remove blade, replace with new one and tighten hardware. Properly dispose of old blade. Caution: Blades are sharp. Handle with care when replacing and disposing of old blades.
Mini Round Baler SRB-870 Maintenance Maintenance Schedule: Safety: Any maintenance is to be done with tractor engine off, baler not running. • Wear protective gear when servicing the machine, gloves, eye protection, etc. • It is best to perform maintenance with the machine on level ground.
Page 28
Mini Round Baler SRB-870 Maintenance Lubrication Points Gearbox Fill Plug Hydraulic Reservoir Gearbox Drain Plug Hydraulic Pump Gearbox Grease Zerk Grease Zerks Binding Arm Actuator Arm - both sides Rear door pivot Binding Arm Gearbox...
Page 29
Mini Round Baler SRB-870 Maintenance Lubrication Points (continued) Link pivot Tension Arm Pivot Link pivot Grease Zerk Pivots and Roller Chain Shear Bolt NOTE: On some machines the drive pulley has two holes. If your machine has two holes, DO NOT USE TWO SHEAR BOLTS! Only one shear bolt is required to function properly.
Page 30
Mini Round Baler SRB-870 Notes: This chart is an approximate estimate of torque values. Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual.
Page 31
Mini Round Baler SRB-870 Page left blank intentionally...
Page 32
Mini Round Baler SRB-870 Parts Manual 10/12/21...
Mini Round Baler SRB-870 Warranty LIMITED WARRANTY Belco Resources Equipment warrants to the original purchaser of any new piece of machinery from Belco Re- sources Equipment, purchased from an authorized Belco Resources Equipment dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and mu- nicipalities’...
Page 68
Mini Round Baler SRB-870 Page left blank intentionally...
Page 69
Mini Round Baler SRB-870 Page left blank intentionally...