H3C S5130S-EI Series Installation Manual
  1. Manuals
  2. Brands
  3. H3C Manuals
  4. Switch
  5. S5130S-EI series
  6. Installation manual

H3C S5130S-EI Series Installation Manual

Hide thumbs Also See for S5130S-EI Series:
Table of Contents

Advertisement

Quick Links

Download this manual
H3C S5130S-EI Switch Series
Installation Guide
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W108-20210427

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S5130S-EI Series and is the answer not in the manual?

Questions and answers

Related Manuals for H3C S5130S-EI Series

Summary of Contents for H3C S5130S-EI Series

  • Page 1 H3C S5130S-EI Switch Series Installation Guide New H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6W108-20210427...
  • Page 2 The information in this document is subject to change without notice. All contents in this document, including statements, information, and recommendations, are believed to be accurate, but they are presented without warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions contained herein.
  • Page 3 Preface H3C S5130S-EI Switch Series Installation Guide describes the appearance, installation, power-on, maintenance, and troubleshooting of the H3C S5130S-EI Switch Series. This preface includes the following topics about the documentation: • Audience. • Conventions. • Documentation feedback. Audience This documentation is intended for: •...
  • Page 4 Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury. An alert that calls attention to important information that if not understood or followed CAUTION: can result in data loss, data corruption, or damage to hardware or software. An alert that calls attention to essential information.
  • Page 5 Documentation feedback You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments.

  • Page 6: Table Of Contents

    Contents 1 Preparing for installation ·········································································· 1-1 Safety recommendations ································································································································ 1-3 Examining the installation site ························································································································· 1-3 Temperature/humidity ····························································································································· 1-3 Cleanliness ·············································································································································· 1-4 Corrosive gas limit ··································································································································· 1-4 EMI ·························································································································································· 1-5 Laser safety ············································································································································· 1-6 Installation tools ·············································································································································· 1-6 2 Installing the switch ·················································································· 2-7 Installing the switch in a 19-inch rack··············································································································...
  • Page 7 Symptom ··············································································································································· 5-41 Solution ················································································································································· 5-41 Fan tray failure ·············································································································································· 5-42 Symptom ··············································································································································· 5-42 Solution ················································································································································· 5-42 Configuration terminal issues ························································································································ 5-42 No display on the configuration terminal ······························································································· 5-42 Garbled display on the configuration terminal ······················································································· 5-42...

  • Page 8: Preparing For Installation

    Preparing for installation This document is applicable to the S5130S-EI switch series. Table1-1 describes the S5130S-EI switch series models. Table1-1 S5130S-EI switch series models Model Product code (PID) Non-PoE switch models LS-5130S-10P-EI S5130S-10P-EI LS-5130S-10P-EI-GL LS-5130S-12TP-EI S5130S-12TP-EI LS-5130S-12TP-EI-GL LS-5130S-20P-EI S5130S-20P-EI LS-5130S-20P-EI-GL LS-5130S-20P-EI-H1 LS-5130S-28P-EI S5130S-28P-EI...
  • Page 9 Model Product code (PID) LS-5130S-28MP-EI S5130S-28MP-EI LS-5130S-28MP-EI-GL LS-5130S-52MP-EI S5130S-52MP-EI LS-5130S-52MP-EI-GL S5130S-28PS-EI LS-5130S-28PS-EI LS-5130S-28ST-EI S5130S-28ST-EI LS-5130S-28ST-EI-GL LS-5130S-52ST-EI S5130S-52ST-EI LS-5130S-52ST-EI-GL PoE switch models LS-5130S-10P-HPWR-EI S5130S-10P-HPWR-EI LS-5130S-10P-HPWR-EI-GL LS-5130S-12TP-HPWR-EI S5130S-12TP-HPWR-EI LS-5130S-12TP-HPWR-EI-GL LS-5130S-20P-PWR-EI S5130S-20P-PWR-EI LS-5130S-20P-PWR-EI-GL LS-5130S-28P-PWR-EI LS-5130S-28P-PWR-EI-GL S5130S-28P-PWR-EI LS-5130S-28P-PWR-EI-H1 LS-5130S-28P-HPWR-EI S5130S-28P-HPWR-EI LS-5130S-28P-HPWR-EI-GL LS-5130S-52P-PWR-EI S5130S-52P-PWR-EI LS-5130S-52P-PWR-EI-GL LS-5130S-16S-PWR-EI S5130S-16S-PWR-EI LS-5130S-16S-PWR-EI-GL...

  • Page 10: Safety Recommendations

    Model Product code (PID) LS-5130S-10MS-UPWR-EI-GL LS-5130S-28ST-PWR-EI S5130S-28ST-PWR-EI LS-5130S-28ST-PWR-EI-GL LS-5130S-52ST-PWR-EI S5130S-52ST-PWR-EI LS-5130S-52ST-PWR-EI-GL NOTE: Switches of the same model but different PIDs might differ in hardware and software features. You can view the PID of a switch on the label located on its rear panel or top panel. Safety recommendations To avoid equipment damage or bodily injury, read the following safety recommendations before installation.

  • Page 11: Cleanliness

    • Lasting low relative humidity can cause washer contraction and ESD and cause problems including loose mounting screws and circuit failure. • High temperature can accelerate the aging of insulation materials and significantly lower the reliability and lifespan of the switch. For the temperature and humidity requirements of different switch models, see technical specifications in Hardware Information and Specifications.

  • Page 12: Emi

    Average concentration (mg/m Maximum concentration (mg/m 0.05 CAUTION: As a best practice, control the corrosive gas concentrations in the equipment room at their average values. Make sure the corrosive gas concentrations do not exceed 30 minutes per day at their maximum values.

  • Page 13: Laser Safety

    Laser safety WARNING! Disconnected optical fibers or transceiver modules might emit invisible laser light. Do not stare into beams or view directly with optical instruments when the switch is operating. The switch is a Class 1 laser device. Installation tools No installation tools are provided with the switch.

  • Page 14: Installing The Switch

    CAUTION: Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence. Figure2-1 Hardware installation flow Start...

  • Page 15: Installing The Switch In A 19-Inch Rack

    Installing the switch in a 19-inch rack Mounting brackets Table2-2 describes the mounting brackets applicable to the switch. Table2-2 Mounting brackets applicable to the switch Switch model Mounting brackets Views S5130S-28P-EI S5130S-28P-EI-M S5130S-28TP-EI S5130S-52P-EI S5130S-52P-EI-M S5130S-52TP-EI S5130S-28S-EI S5130S-28S-EI-M S5130S-28S-EI-DP S5130S-52S-EI S5130S-52S-EI-M S5130S-28P-PWR-EI Mounting brackets A (provided)

  • Page 16: Attaching The Mounting Brackets To The Switch

    Switch model Mounting brackets Views S5130S-10MS-UPWR-EI S5130S-10P-EI Mounting brackets E with product code See E in Figure2-2. SOHO-SWITCH-FL-01 (optional) S5130S-12TP-EI Figure2-2 Mounting brackets (1) Screw hole for attaching the bracket to the switch (2 ) Screw hole for attaching the bracket to the rack post Attaching the mounting brackets to the switch Determine the installation position for the mounting brackets.
  • Page 17 Align one mounting bracket with the screw holes at the mounting position. Use M4 screws to attach the mounting bracket to the chassis. See Figure2-3 for installing mounting bracket A, Figure2-4 Figure2-5 for installing mounting bracket B, and Figure2-6 for installing mounting bracket C, D, and E (C as an example).

  • Page 18: Rack-Mounting The Switch

    Figure2-6 Attaching mounting bracket C (S5130S-20P-PWR-EI switch) Rack-mounting the switch This task requires two people. To mount the switch in the rack: Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded. Verify that the mounting brackets have been securely attached to the switch chassis. Install cage nuts in the mounting holes in the rack posts.

  • Page 19: Mounting The Switch On A Workbench

    Figure2-8 Mounting an S5130S-52F-EI switch in the rack (power supply side mounting position for the mounting brackets) Figure2-9 Mounting an S5130S-20P-PWR-EI switch in the rack Mounting the switch on a workbench IMPORTANT: • Ensure 10 cm (3.9 in) of clearance around the chassis for heat dissipation. •...

  • Page 20: Mounting The Switch On A Wall

    Mounting the switch on a wall CAUTION: • Before drilling holes in a wall, make sure no electrical lines exist in the wall. • Leave a minimum clearance of 10 mm (0.39 in) around the chassis for heat dissipation. Table2-2 describes the switch models that support wall mounting and installation holes distances required for wall-mounting the switch.
  • Page 21 Table2-2 for the distance requirement between the two holes. Figure2-11 Installing the switch on a wall (1) Drill two holes with a diameter of 6 mm (0.24 in) (7 mm/0.28 in for an S5130S-16S-PWR-EI switch) and a depth of 25 mm (0.98 in) at the marked locations. Hammer the screw anchors into the wall and use a Phillips screwdriver to fasten the screw into the screw anchor.

  • Page 22: Grounding The Switch

    Grounding the switch WARNING! Correctly connecting the switch grounding cable is crucial to lightning protection and EMI protection. The power input end of the switch has a noise filter, whose central ground is directly connected to the chassis to form the chassis ground (commonly known as PGND). You must securely connect this chassis ground to the earth to minimize the potential for system damage, maximize the safety at the site, and minimize EMI susceptibility of the system.

  • Page 23: Grounding The Switch With A Grounding Conductor Buried In The Earth Ground

    Figure2-14 Attaching the grounding cable to the grounding hole of the switch (S5130S-28P-HPWR-EI switch) (1) Grounding screw (2) Ring terminal (3) Grounding sign (4) Grounding hole (5) Grounding cable Connect the other end of the grounding cable to the grounding strip. a.

  • Page 24: Installing And Removing Power Supplies

    Weld the yellow-green grounding cable to the angel iron or steel tube and treat the joint for corrosion protection. Figure2-16 Grounding the switch by burying the grounding conductor into the earth ground (1) Grounding screw (2) Grounding cable (3) Earth (4) Joint (5) Grounding conductor (6) Chassis rear panel...

  • Page 25: Installing A Power Supply

    Installing a power supply Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded. Unpack the power supply and verify that the power supply model is as required. Remove the filler panel (if any) from the target slot. If you require only one power supply, install it in power supply slot 1 and make sure a filler panel is installed in power supply slot 2.

  • Page 26: Connecting The Power Cord

    S5130S-28F-EI S5130S-52F-EI –48 VDC power source in the Connecting the power cord for a equipment room PSR150-D1 power supply H3C RPS800-A or Connecting the power cord for a RPS1600-A PSR150-D1 power supply S5130S-16S-PWR-EI S5130S-16S-UPWR-EI-Q Connecting the AC power cord for the fixed...

  • Page 27: Connecting The Ac Power Cord For The Fixed Ac Power Supply (Method 1)

    Switch model Available power source Connection procedure reference equipment room DC power supply (method 2) Connecting the AC power cord for the fixed Other S5130S-EI switches AC power source AC power supply (method 1) The S5130S-28F-EI and S5130S-52F-EI switches use removable power supplies. The PSR75-12A, PSR150-A1, and PSR150-D1 power supplies are available for the switch.

  • Page 28: Connecting The Ac Power Cord For The Fixed Ac Power Supply (Method 2)

    (method 1) CAUTION: • To connect the switch to a –48 VDC power source, use the DC power cord provided by H3C. To avoid connection mistakes, identify the positive (+) and negative (-) marks on the two wires of the DC power cord before connection.

  • Page 29: Connecting The Dc Power Cord For The Fixed Dc Power Supply (Method 2)

    To connect the DC power cord for the fixed DC power supply: Correctly orient the DC power cord plug and insert the plug into the power receptacle on the power supply. If you orient the DC power cord plug upside down, you cannot insert the plug into the power receptacle.
  • Page 30 Figure2-26 Attaching the terminal block to the fixed DC power supply Figure2-27 Securing the DC power cord to the terminal block Connecting the power cord for a PSR75-12A/PSR150-A1 power supply Pull the bail latch leftward, as shown in Figure2-28. Connect the plug of the power cord to the power receptacle on the switch. See Figure2-29. Pull the bail latch rightward to secure the plug to the power receptacle.

  • Page 31: Connecting The Power Cord For A Psr75-12A/Psr150-A1 Power Supply

    (– or L–) to the negative terminal (–) and the positive wire (+ or M/N) to the positive terminal (+). • To use an H3C RPS to supply power to the power supply, use a compatible RPS power cord to connect the RPS to the power supply.

  • Page 32: Verifying The Installation

    Figure2-30 Connecting the DC power cord for a PSR150-D1 power supply (S5130S-52F-EI) Verifying the installation After you complete the installation, verify that: • There is enough space for heat dissipation around the switch, and the rack or workbench is stable. •...

  • Page 33: Accessing The Switch For The First Time

    Accessing the switch for the first time Connecting the switch to a configuration terminal The following switch models each provide a serial console port and a micro USB console port. You can access the switch from either port. If you connect both ports, only the micro USB console port is available.

  • Page 34: Connecting A Db9-To-Rj45 Console Cable

    As a best practice, use a serial console cable for connection. The switch is not provided with a serial console cable or a micro USB console cable. Prepare an H3C console cable or prepare a micro USB console cable yourself.

  • Page 35: Connecting A Usb-To-Rj45 Console Cable

    Figure3-2 DB9-to-RJ45 console cable Table3-2 DB9-to-RJ45 console cable signal pinout RJ-45 Signal DB-9 Signal To connect the switch to a configuration terminal (for example, a PC) by using a DB9-to-RJ45 console cable: Plug the DB-9 female connector of the DB9-to-RJ45 console cable to the serial port on the PC. Connect the RJ-45 connector to the serial console port on the switch.
  • Page 36 Click the following link, or copy it to the address bar on your browser and download the USB-to-RJ45 console driver. http://www.h3c.com/en/home/USB_to_RJ45_Console/ View the TXT file Read me in the Windows folder to check whether the Windows system of the configuration terminal supports the driver.

  • Page 37: Connecting A Micro Usb Console Cable

    Figure3-5 Finishing the driver installation Connect the standard USB connector of the cable to the USB port of the configuration terminal. Connect the RJ-45 connector of the cable to the console port of the switch. Connecting a micro USB console cable A micro USB console cable has a micro USB connector at one end to connect to the micro USB console port of the switch, and a standard USB connector at the other end to connect to the USB port on the configuration terminal.
  • Page 38 Click the following link, or copy it to the address bar on the browser to log in to download and install the USB console driver on the configuration terminal. http://www.h3c.com/en/home/USB_Console/ Select a driver program according to the operating system you use: XR21V1410_XR21B1411_Windows_Ver1840_x86_Installer.EXE—32-bit operating...

  • Page 39: Setting Terminal Parameters

    Figure3-8 Software Installation Click Finish. Figure3-9 Completing the device driver installation wizard Setting terminal parameters To configure and manage the switch through the console port, you must run a terminal emulator program, such as TeraTermPro, on your configuration terminal. You can use the emulator program to 3-32...

  • Page 40: Powering On The Switch

    connect a network device, a Telnet site, or an SSH site. For more information about the terminal emulator programs, see the user guides for these programs. Configure the terminal parameters as follows: • Bits per second—9,600. • Data bits—8. • Stop bits—1.

  • Page 41: Setting Up An Irf Fabric

    Setting up an IRF fabric You can use H3C IRF technology to connect and virtualize the switches into a large virtual switch called an "IRF fabric" for flattened network topology, and high availability, scalability, and manageability. IRF fabric setup flowchart...

  • Page 42: Planning Irf Fabric Setup

    Step Description "Installing the switch in a 19-inch rack" or "Mounting the switch Install IRF member switches. on a workbench." Connect grounding cables and "Grounding the switch" and "Connecting the power cord." power cords. Power on the switches. See the IRF configuration guide or virtual technologies Configure basic IRF settings.

  • Page 43: Identifying Irf Physical Ports On The Member Switches

    The switch can form an IRF fabric only with switches from the same switch series. For the physical ports that can be used for IRF connections and the restrictions for using the ports, see Table4-1. The IRF physical ports can set up IRF connections only when operating at their highest speeds. For example, a 10-GE port must operate at 10 Gbps.
  • Page 44 Table4-1 IRF physical ports and use restrictions Candidate IRF physical Restrictions for using the ports for Device model ports IRF connections S5130S-16S-PWR-EI S5130S-16S-UPWR-EI-Q S5130S-28S-EI All physical ports to be bound to an IRF port must have the same data rate. S5130S-28PS-EI The port must operate at its highest speed.

  • Page 45: Planning The Cabling Scheme

    Candidate IRF physical Restrictions for using the ports for Device model ports IRF connections the other group. To bind multiple ports to an IRF port, make sure the ports are in the same group. Ports in one group can be bound to different IRF ports. The port must operate at 1 Gbps.

  • Page 46: Configuring Basic Irf Settings

    Use twisted pair cables, SFP/SFP+ cables, or SFP/SFP+ transceiver modules and fibers to connect the IRF member switches as planned. Wear an ESD wrist strap when you connect twisted pair cables, SFP/SFP+ cables, or SFP/SFP+ transceiver modules and fibers. For how to connect them, see H3C Transceiver Modules User Guide. 4-39...

  • Page 47: Verifying The Irf Fabric Setup

    Verifying the IRF fabric setup To verify the basic functionality of the IRF fabric after you finish configuring basic IRF settings and connecting IRF ports: Log in to the IRF fabric through the console port of any member switch. Create a Layer 3 interface, assign it an IP address, and make sure the IRF fabric and the remote network management station can reach each other.

  • Page 48: Symptom

    Verify that the operating temperature of the switch is in the acceptable range, and the power supply has good ventilation. Overtemperature can cause the power supply to stop working and enter protection mode. If the issue persists, contact H3C Support. Removable power supply failure The S5130S-28F-EI and S5130S-52F-EI switches use removable power supplies. You can determine the power supply operating status by examining the power supply LEDs PWR1 and PWR2 on the switch front panel.
  • Page 49 Fan tray failure Symptom The system status LED on the switch indicates a fan tray failure. Solution When a fan tray issue occurs, contact H3C Support. Configuration terminal issues No display on the configuration terminal Symptom The configuration terminal does not have display when the switch is powered on.
  • Page 50 Stop bits—1.  Flow control—None.  If the issue persists, contact H3C Support. 5-43...
  • Page 51 Contents 1 Product models and technical specifications ············································ 1-3 Product models ··············································································································································· 1-3 Technical specifications ·································································································································· 1-5 Non-PoE switch models ·························································································································· 1-5 PoE switch models ································································································································ 1-12 2 Chassis views ························································································ 2-19 S5130S-10P-EI ············································································································································· 2-19 S5130S-12TP-EI ··········································································································································· 2-19 S5130S-20P-EI ············································································································································· 2-20 S5130S-28P-EI/S5130S-28P-EI-M ···············································································································...
  • Page 52 LEDs ····························································································································································· 4-57 System status LED ································································································································ 4-57 Management Ethernet port LED ··········································································································· 4-57 Power supply status LED ······················································································································ 4-57 RPS status LED ···································································································································· 4-58 Mode LED (MODE) ······························································································································· 4-58 SFP/SFP+ port LED ······························································································································ 4-58 Ethernet port LEDs ································································································································ 4-58...

  • Page 53: Product Models And Technical Specifications

    Product models and technical specifications Product models This document is applicable to the S5130S-EI switch series. Table1-1 describes the S5130S-EI switch series models. Table1-1 S5130S-EI switch series models Model Product code (PID) Non-PoE switch models LS-5130S-10P-EI S5130S-10P-EI LS-5130S-10P-EI-GL LS-5130S-12TP-EI S5130S-12TP-EI LS-5130S-12TP-EI-GL LS-5130S-20P-EI S5130S-20P-EI...
  • Page 54 Model Product code (PID) LS-5130S-28F-EI S5130S-28F-EI LS-5130S-28F-EI-GL LS-5130S-52F-EI S5130S-52F-EI LS-5130S-52F-EI-GL LS-5130S-28MP-EI S5130S-28MP-EI LS-5130S-28MP-EI-GL LS-5130S-52MP-EI S5130S-52MP-EI LS-5130S-52MP-EI-GL S5130S-28PS-EI LS-5130S-28PS-EI LS-5130S-28ST-EI S5130S-28ST-EI LS-5130S-28ST-EI-GL LS-5130S-52ST-EI S5130S-52ST-EI LS-5130S-52ST-EI-GL PoE switch models LS-5130S-10P-HPWR-EI S5130S-10P-HPWR-EI LS-5130S-10P-HPWR-EI-GL LS-5130S-12TP-HPWR-EI S5130S-12TP-HPWR-EI LS-5130S-12TP-HPWR-EI-GL LS-5130S-20P-PWR-EI S5130S-20P-PWR-EI LS-5130S-20P-PWR-EI-GL LS-5130S-28P-PWR-EI S5130S-28P-PWR-EI LS-5130S-28P-PWR-EI-GL LS-5130S-28P-PWR-EI-H1 LS-5130S-28P-HPWR-EI S5130S-28P-HPWR-EI LS-5130S-28P-HPWR-EI-GL...

  • Page 55: Technical Specifications

    Model Product code (PID) S5130S-52S-PWR-EI-AC LS-5130S-52S-PWR-EI-AC LS-5130S-28MP-HPWR-EI S5130S-28MP-HPWR-EI LS-5130S-28MP-HPWR-EI-GL LS-5130S-10MS-UPWR-EI S5130S-10MS-UPWR-EI LS-5130S-10MS-UPWR-EI-GL LS-5130S-28ST-PWR-EI S5130S-28ST-PWR-EI LS-5130S-28ST-PWR-EI-GL LS-5130S-52ST-PWR-EI S5130S-52ST-PWR-EI LS-5130S-52ST-PWR-EI-GL NOTE: Switches of the same model but different PIDs might differ in hardware and software features. You can view the PID of a switch on the label located on its rear panel or top panel. Technical specifications Non-PoE switch models Table1-2 Technical specifications for non-PoE switch models (1)
  • Page 56 Item S5130S-10P-EI S5130S-12TP-EI S5130S-20P-EI compliance Melting current of 2 A/250 V 2 A/250 V 2 A/250 V power supply fuse Natural cooling without Natural cooling without fan Natural cooling without Cooling system fan trays trays fan trays Operating –5°C to +45°C (23°F to 113°F) temperature Operating 5% to 95%, noncondensing...
  • Page 57 Table1-4 Technical specifications for non-PoE switch models (3) S5130S-28S-EI S5130S-52S-EI Item S5130S-28TP-EI S5130S-52TP-EI S5130S-28S-EI-M S5130S-52S-EI-M 43.6 × 440 × 160 43.6 × 440 × 260 43.6 × 440 × 160 43.6 × 440 × 230 mm Dimensions mm (1.72 × 17.32 × mm (1.72 ×...
  • Page 58 S5130S-28S-EI S5130S-52S-EI Item S5130S-28TP-EI S5130S-52TP-EI S5130S-28S-EI-M S5130S-52S-EI-M of the chassis and -PWR-EI-H1: exhaust heated air out exhaust heated air Natural cooling from the right side and power supply side. out from the right without fan trays. side and the power supply side.
  • Page 59 Rated voltage: –48 VDC to –60 VDC • Max voltage: –36 VDC to –72 VDC DC power source for the PSR150-D1 power supply: –48 VDC power source in the equipment room or an RPS (H3C RPS800-A or RPS1600-A) • • 1 × PSR75-12A: 15 W 1 ×...
  • Page 60 Item S5130S-28MP-EI S5130S-52MP-EI • 1 × serial console port • 1 × micro USB console port Console port When both ports are connected, only the micro USB console port is available. 10/100/1000BASE-T autosensing Ethernet port 5G/2.5G/1000BASE-T autosensing Ethernet port SFP port •...
  • Page 61 S5130S-28ST- S5130S-28PS- Item S5130S-28S-EI-DP S5130S-52ST-EI form combo interfaces with their corresponding SFP ports, respectively.) 10/5/2.5/1GBA SE-T autosensing Ethernet port 8 (The eight SFP ports form combo interfaces with their SFP port corresponding 10/100/1000BAS E-T autosensing Ethernet ports, respectively.) SFP+ port AC power source: •...

  • Page 62: Poe Switch Models

    PoE switch models Table1-8 Technical specifications for PoE switch models (1) Item S5130S-10P-HPWR-EI S5130S-12TP-HPWR-EI S5130S-20P-PWR-EI Dimensions (H × W 43.6 × 330 × 230 mm 43.6 × 330 × 230 mm (1.72 × 43.6 × 330 × 230 mm × D) (1.72 ×...
  • Page 63 Item S5130S-10P-HPWR-EI S5130S-12TP-HPWR-EI S5130S-20P-PWR-EI compliance 60950-1/GB4943.1 Table1-9 Technical specifications for PoE switch models (2) Item S5130S-28ST-PWR-EI S5130S-52ST-PWR-EI Dimensions (H × W × 43.6 × 440 × 320 mm (1.72 × 17.32 × 43.6 × 440 × 320 mm (1.72 × 17.32 × 12.60 in) 12.60 in) ≤...
  • Page 64 Max voltage: 90 VAC to 264 VAC @ 100 VAC to 240 VAC to 240 47 to 63 Hz VAC @ 50 or 60 VAC @ 50 or DC power source: H3C RPS1600-A 60 Hz Input voltage • Rated voltage: –54 VDC to –57 VDC •...
  • Page 65 of power supply fuse Using fixed fan trays Using fixed fan Using fixed fan trays Using fixed fan to draw ambient air in trays to draw to draw ambient air trays to draw from the left side and ambient air in from in from the left side ambient air in from Cooling system...
  • Page 66 • Rated voltage: 100 VAC to 240 VAC @ 50 or 60 Hz • Max voltage: 90 VAC to 264 VAC @ 47 to 63 Hz DC power source: H3C RPS1600-A (supported only by S5130S-52S-PWR-EI and Input S5130S-28S-HPWR-EI switches) voltage •...
  • Page 67 S5130S-28 S5130S-5 S5130S-16 S5130S-28 S5130S-52 S5130S-28 Item S-HPWR- 2S-PWR- S-PWR-EI S-PWR-EI S-PWR-EI S-HPWR-EI EI-Q EI-AC power supply fuse Using fixed Using fixed Using fixed Using fixed fan trays to fan trays to fan trays to fan trays to draw draw ambient draw ambient draw ambient ambient air...
  • Page 68 S5130S-28MP-HP S5130S-10MS- Item R-EI-Q R-EI-Q WR-EI UPWR-EI DC power source: H3C RPS1600-A (supported only by the S5130S-28MP-UPWR-EI and S5130S-10MS-UPWR-EI switches) • Rated voltage: –54 VDC to –57 VDC • Max voltage: Single DC input: –44 VDC to –60 VDC ...

  • Page 69: Chassis Views

    Chassis views S5130S-10P-EI Figure2-1 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP port LED (4) System status LED (SYS) (5) Console port (CONSOLE) (6) SFP port Figure2-2 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-12TP-EI Figure2-3 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port...

  • Page 70: S5130S-20P-Ei

    Figure2-4 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-20P-EI Figure2-5 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP port LED (4) System status LED (SYS) (5) Console port (CONSOLE) (6) SFP port Figure2-6 Rear panel (1) AC-input power receptacle (2) Grounding screw...

  • Page 71: S5130S-28P-Ei/S5130S-28P-Ei-M

    S5130S-28P-EI/S5130S-28P-EI-M Figure2-7 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP port LED (4) System status LED (SYS) (5) Console port (CONSOLE) (6) SFP port Figure2-8 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-28TP-EI Figure2-9 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port...

  • Page 72: S5130S-52P-Ei/S5130S-52P-Ei-M

    Figure2-10 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-52P-EI/S5130S-52P-EI-M Figure2-11 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) SFP port LED (5) System status LED (SYS) (6) SFP port Figure2-12 Rear panel (1) Grounding screw (2) AC-input power receptacle...

  • Page 73: S5130S-52Tp-Ei

    S5130S-52TP-EI Figure2-13 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) Micro USB console port (5) System status LED (SYS) (6) SFP port LED (7) SFP port Figure2-14 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-28S-EI/S5130S-28S-EI-M Figure2-15 Front panel...

  • Page 74: S5130S-28S-Ei-Dp

    Figure2-16 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-28S-EI-DP Figure2-17 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) Console port (CONSOLE) (3) 10/100/1000BASE-T autosensing Ethernet port LED (4) System status LED (SYS) (5) SFP+ port LED (6) Micro USB console port (7) SFP+ port Figure2-18 Rear panel (1) Grounding screw...

  • Page 75: S5130S-52S-Ei/S5130S-52S-Ei-M

    S5130S-52S-EI/S5130S-52S-EI-M Figure2-19 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) Micro USB console port (5) SFP+ port LED (6) System status LED (SYS) (7) SFP+ port Figure2-20 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-28F-EI Figure2-21 Front panel...

  • Page 76: S5130S-52F-Ei

    (9) Power supply 2 status LED (PWR2) (10) Power supply 1 status LED (PWR1) (11) SFP+ port LED (12) Management Ethernet port status LED (ACT/LINK) (13) SFP+ port Figure2-22 Rear panel (1) Grounding screw (2) Power supply 1 (PWR1) (3) Power supply 2 (PWR2) The S5130S-28F-EI switch comes with power supply 1 empty and power supply slot 2 installed with a filler panel.

  • Page 77: S5130S-28Mp-Ei

    (1) Grounding screw (2) Power supply 1 (PWR1) (3) Power supply 2 (PWR2) The S5130S-52F-EI switch comes with power supply slot 1 empty and power supply slot 2 installed with a filler panel. You can install one or two power supplies for the switch as needed. In Figure2-24, two PSR150-A1 AC power supplies are installed.

  • Page 78: S5130S-52Mp-Ei

    S5130S-52MP-EI Figure2-27 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) 5G/2.5G/1000BASE-T autosensing Ethernet port (5GBASE-T) (4) Console port (CONSOLE) (5) Micro USB console port (6) System status LED (SYS) (7) SFP port (8) SFP port LED (9) 5G/2.5G/1000BASE-T autosensing Ethernet port LED Figure2-28 Rear panel (1) Grounding screw...

  • Page 79: S5130S-28St-Ei

    (1) 10/100/1000BASE-T autosensing Ethernet port (3) SFP port (4) Management Ethernet port (5) Console port (CONSOLE) (6) System status LED (SYS) (7) SFP+ port (8) SFP+ port LED (9) Management Ethernet port status LED (ACT/LINK) (10) SFP port LED Figure2-30 Rear panel (1) Grounding screw (2) AC-input power receptacle (3) DC-input power receptacle...

  • Page 80: S5130S-52St-Ei

    S5130S-52ST-EI Figure2-33 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP+ port (4) Console port (CONSOLE) (5) 10/5/2.5/1GBASE-T autosensing Ethernet port (6) System status LED (SYS) (7) 10/5/2.5/1GBASE-T autosensing Ethernet port LED (8) SFP+ port LED Figure2-34 Rear panel (1) AC-input power receptacle (2) Grounding screw...

  • Page 81: S5130S-12Tp-Hpwr-Ei

    Figure2-36 Rear panel (1) AC-input power receptacle (2) Grounding screw S5130S-12TP-HPWR-EI Figure2-37 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP port LED (4) System status LED (SYS) (5) Mode LED (MODE) (6) Port LED mode switching button (7) Console port (CONSOLE) (8) SFP port Figure2-38 Rear panel...

  • Page 82: S5130S-20P-Pwr-Ei

    S5130S-20P-PWR-EI Figure2-39 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP port LED (4) System status LED (SYS) (5) Mode LED (MODE) (6) Port LED mode switching button (7) Console port (CONSOLE) (8) SFP port Figure2-40 Rear panel (1) AC-input power receptacle (2) Grounding screw...

  • Page 83: S5130S-28P-Hpwr-Ei

    Figure2-42 Rear panel (product code LS-5130S-28P-PWR-EI) (1) Grounding screw (2) AC-input power receptacle Figure2-43 Rear panel (product code LS-5130S-28P-PWR-EI-H1) (1) Grounding screw (2) AC-input power receptacle S5130S-28P-HPWR-EI Figure2-44 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) Console port (CONSOLE) (3) Port LED mode switching button (4) 10/100/1000BASE-T autosensing Ethernet port LED (5) System status LED (SYS) (6) RPS status LED (RPS)

  • Page 84: S5130S-52P-Pwr-Ei

    Figure2-45 Rear panel (1) Grounding screw (2) AC-input power receptacle (3) DC-input power receptacle S5130S-52P-PWR-EI Figure2-46 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) Port LED mode switching button (5) System status LED (SYS) (6) RPS status LED (RPS) (7) Mode LED (MODE) (8) SFP port...

  • Page 85: S5130S-16S-Pwr-Ei

    S5130S-16S-PWR-EI Figure2-48 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) Port LED mode switching button (3) 10/100/1000BASE-T autosensing Ethernet port LED (4) SFP+ port LED (5) System status LED (SYS) (6) Mode LED (MODE) (7) Micro USB console port (8) Console port (CONSOLE) (9) SFP+ port Figure2-49 Rear panel (1) AC-input power receptacle...

  • Page 86: S5130S-28S-Pwr-Ei

    Figure2-51 Rear panel (1) AC-input power receptacle (2) Heat sink (3) Grounding screw S5130S-28S-PWR-EI Figure2-52 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) Port LED mode switching button (3) 10/100/1000BASE-T autosensing Ethernet port LED (4) SFP+ port LED (5) System status LED (SYS) (6) Mode LED (MODE) (7) Micro USB console port (8) Console port (CONSOLE)

  • Page 87: S5130S-28S-Hpwr-Ei

    Figure2-54 Rear panel (product code LS-5130S-28S-PWR-EI-H1) (1) Grounding screw (2) AC-input power receptacle S5130S-28S-HPWR-EI Figure2-55 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) SFP port (3) Console port (CONSOLE) (4) Port LED mode switching button (5) 10/100/1000BASE-T autosensing Ethernet port LED (6) System status LED (SYS) (7) RPS status LED (RPS) (8) Mode LED (MODE)

  • Page 88: S5130S-28S-Hpwr-Ei-Q

    S5130S-28S-HPWR-EI-Q Figure2-57 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) Port LED mode switching button (3) 10/100/1000BASE-T autosensing Ethernet port LED (4) SFP+ port LED (5) System status LED (SYS) (6) Mode LED (MODE) (7) Micro USB console port (8) Console port (CONSOLE) (9) SFP+ port Figure2-58 Rear panel (1) AC-input power receptacle...

  • Page 89: S5130S-52S-Pwr-Ei

    (1) 10/100/1000BASE-T autosensing Ethernet port (2) Console port (CONSOLE) (4) 10/100/1000BASE-T autosensing Ethernet port LED (5) System status LED (SYS) (6) Mode LED (MODE) (7) SFP+ port LED (8) Micro USB console port (9) SFP+ port Figure2-60 Rear panel (1) Grounding screw (2) AC-input power receptacle (3) Heat sink S5130S-52S-PWR-EI...

  • Page 90: S5130S-28Mp-Hpwr-Ei

    S5130S-28MP-HPWR-EI Figure2-63 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 5G/2.5G/1000BASE-T autosensing Ethernet port (5GBASE-T) (3) Console port (CONSOLE) (4) Port LED mode switching button (5) 10/100/1000BASE-T autosensing Ethernet port LED (6) System status LED (SYS) (7) RPS status LED (RPS) (8) Mode LED (MODE) (9) SFP port LED (10) 5G/2.5G/1000BASE-T autosensing Ethernet port LED...

  • Page 91: S5130S-28St-Pwr-Ei

    (1) 2.5G/1000/100BASE-T autosensing Ethernet port (2) SFP+ port (3) Console port (CONSOLE) (4) Port LED mode switching button (5) 2.5G/1000/100BASE-T autosensing Ethernet port LED (6) System status LED (SYS) (7) RPS status LED (RPS) (8) SFP+ port LED (9) Mode LED (MODE) (10) Micro USB console port Figure2-66 Rear panel (1) Grounding screw...

  • Page 92: S5130S-52St-Pwr-Ei

    Figure2-68 Rear panel (1) Grounding screw (2) AC-input power receptacle S5130S-52ST-PWR-EI Figure2-69 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) SFP+ port (4) Console port (CONSOLE) (5) Port LED mode switching button (6) Mode LED (MODE) (7) System status LED (SYS) (8) 10/5/2.5/1GBASE-T autosensing Ethernet port (9) 10/5/2.5/1GBASE-T autosensing Ethernet port LED...

  • Page 93: S5130S-52P-Pwr-Ei-Ac

    S5130S-52P-PWR-EI-AC Figure2-71 Front panel (1) 10/100/1000BASE-T autosensing Ethernet port (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) Port LED mode switching button (5) System status LED (SYS) (6) Mode LED (MODE) (7) SFP port LED (8) SFP port Figure2-72 Rear panel (1) Grounding screw (2) AC-input power receptacle...
  • Page 94 (2) 10/100/1000BASE-T autosensing Ethernet port LED (3) Console port (CONSOLE) (4) Port LED mode switching button (5) System status LED (SYS) (6) Mode LED (MODE) (7) Micro USB console port (8) SFP+ port (9) SFP+ port LED Figure2-74 Rear panel (1) Grounding screw (2) AC-input power receptacle 2-44...

  • Page 95: Removable Components

    AC: 100 VAC to 240 VAC @ 50 Hz or 60 Hz Rated input voltage DC: 240 VDC For more information about the power supply, see H3C PSR75-12A AC: 90 VAC to 290 VAC @ PSR75-12A Power Module User 47 Hz to 63 Hz Max input voltage Manual.

  • Page 96: Ports And Leds

    Ports and LEDs Ports Console port Table4-1 Console port specifications Item Serial console port Micro USB console port Connector type RJ-45 Micro USB Type B Compliant standard EIA/TIA-232 USB 2.0 Transmission baud rate 9600 bps (default) to 115200 bps • Provides connection to an •...

  • Page 97: Management Ethernet Port

    Management Ethernet port The S5130S-28F-EI and S5130S-28PS-EI switches each have one management Ethernet port. You can connect the port to a local PC for software loading and debugging or to a remote management station for remote management. Table4-2 Management Ethernet port specifications Item Specification Connector type...

  • Page 98: 2.5G/1000/100Base-T Autosensing Ethernet Port

    Item Specification • 5 Gbps, full duplex • MDI/MDI-X autosensing • 5G mode: 100 m (328.08 ft) over Category-5e or above twisted pair • 2.5G mode: 200 m (656.17 ft) over Category-5e or above Max transmission distance twisted pair • 1G mode: 200 m (656.17 ft) over Category-5e or above twisted pair Transmission medium...

  • Page 99: Sfp Port

    Item Specification • 10G mode: 100 m (328.08 ft) over Category-6 shielded twisted pair or  above twisted pair 60 m (196.85 ft) over Category-5e twisted pair or  Category-6 unshielded twisted pair • Max transmission distance 5G mode: 100 m (328.08 ft) over Category-5e or above twisted pair •...
  • Page 100 SFP port support for SFP Model Restrictions transceiver modules and cables S5130S-10P-HPWR-EI S5130S-28MP-HPWR-EI S5130S-52P-EI S5130S-52P-EI-M S5130S-20P-PWR-EI S5130S-28P-PWR-EI S5130S-52P-PWR-EI S5130S-52P-PWR-EI-AC • SFP ports 9 and 10: GE SFP To use GE transceiver modules transceiver module and cables in with a maximum transmission Table4-8 and FE SFP transceiver S5130S-12TP-EI...
  • Page 101 Table4-8 GE SFP transceiver modules and cables GE SFP Modal Central Cable transceiver Connector bandwidth transmission wavelength specifications module/cable (MHz*km) distance Copper SFP transceiver module Twisted pair SFP-GE-T RJ-45 100 m (328.09 ft) cable Twisted pair SFP-GE-T-D RJ-45 100 m (328.09 ft) cable Fiber SFP transceiver module 550 m (1804.46...
  • Page 102 GE SFP Modal Central Cable Connector transceiver bandwidth transmission wavelength specifications module/cable (MHz*km) distance 9/125 µm SFP-GE-LH40-SM 40 km (24.86 1310 nm single-mode 1310-D miles) optical fiber 9/125 µm SFP-GE-LH40-SM 40 km (24.86 1550 nm single-mode 1550 miles) optical fiber 9/125 µm SFP-GE-LH80-SM 80 km (49.71...
  • Page 103 GE SFP Modal Central Cable Connector transceiver bandwidth transmission wavelength specifications module/cable (MHz*km) distance 9/125 µm SFP-GE-LH80-SM 80 km (49.71 1550 nm single-mode 1550-D miles) optical fiber 9/125 µm SFP-GE-LH100-S 100 km (62.14 1550 nm single-mode M1550 miles) optical fiber TX: 1310 nm SFP-GE-LX-SM13 Single-mode,...

  • Page 104: Sfp+ Port

    • As a best practice, use H3C SFP transceiver modules and cables for the SFP ports. • The H3C SFP transceiver modules and cables available for the SFP ports are subject to change over time. For the most up-to-date list of H3C SFP transceiver modules and cables available for the SFP ports, contact your H3C sales representative or technical support engineer.
  • Page 105 82 m (269.03 ft) 66 m (216.54 ft) 62.5/125 µm 33 m (108.27 ft) multi-mode 26 m (85.30 ft) optical fiber 9/125 µm SFP-XG-LX-SM131 1310 nm single-mode 10 km (6.21 miles) optical fiber 9/125 µm SFP-XG-LX-SM131 1310 nm 10 km (6.21 miles) single-mode optical fiber 9/125 µm...

  • Page 106: Combo Interface

    (2) Pull latch NOTE: • As a best practice, use H3C SFP/SFP+ transceiver modules or SFP+ cables for the SFP+ ports. • The H3C SFP/SFP+ transceiver modules and SFP+ cables available for the SFP+ ports are subject to change over time. For the most up-to-date list of H3C SFP/SFP+ transceiver modules and SFP+ cables available for the SFP+ ports, contact your H3C sales representative or technical support engineer.
  • Page 107 port and a 10/100/1000BASE-T autosensing Ethernet port. Only one of these two ports operates at a time. LEDs System status LED The system status LED shows the operating status of the switch. Table4-13 System status LED description LED mark Status Description Steady yellow Boot ROM booting stage.
  • Page 108 RPS status LED S5130S-28P-HPWR-EI, S5130S-52P-PWR-EI, S5130S-10MS-UPWR-EI, S5130S-28S-HPWR-EI, S5130S-52S-PWR-EI, and S5130S-28MP-HPWR-EI switches support RPS input and each provide an RPS status LED on the front panel to indicate the RPS operating status. Table4-16 RPS status LED description LED mark Status Description Steady green Both the RPS DC input and the AC input are normal.
  • Page 109 • 2.5G/1000/100BASE-T autosensing Ethernet port LEDs • 5G/2.5G/1000BASE-T autosensing Ethernet port LEDs • 10/5/2.5/1GBASE-T autosensing Ethernet port LEDs Table4-20 describes the Ethernet port LEDs on a non-PoE switch. Table4-19 Ethernet port LED description for PoE switch models Mode LED Ethernet port LED Description status status...

Table of Contents