H3C S5130S-EI Series Installation Manual page 44

Table4-1 IRF physical ports and use restrictions
Device model
S5130S-16S-PWR-EI
S5130S-16S-UPWR-EI-Q
S5130S-28S-EI
S5130S-28PS-EI
S5130S-28S-EI-M
S5130S-28S-EI-DP
S5130S-28S-PWR-EI
S5130S-28S-HPWR-EI
S5130S-28S-HPWR-EI-Q
S5130S-28S-UPWR-EI-Q
S5130S-28F-EI
S5130S-52S-EI
S5130S-52S-EI-M
S5130S-52S-PWR-EI
S5130S-52S-PWR-EI-AC
S5130S-52F-EI
S5130S-28MP-EI
S5130S-28MP-HPWR-EI
S5130S-52MP-EI
S5130S-10MS-UPWR-EI
S5130S-28ST-EI
S5130S-52ST-EI
S5130S-28ST-PWR-EI
S5130S-52ST-PWR-EI
Candidate IRF physical
ports
All the following ports on the
front panel:
•
SFP+ ports
•
10/100/1000BASE-T
autosensing ports
(supported only in
F6304 and later)
•
SFP ports (supported
only in F6304 and later)
All the following ports on the
front panel:
•
5G/2.5G/1000BASE-T
autosensing Ethernet
ports
•
10/100/1000BASE-T
autosensing Ethernet
ports
•
SFP ports
All the following ports on the
front panel:
•
2.5G/1000/100BASE-T
autosensing Ethernet
ports
•
SFP+ ports
All the following ports on the
front panel:
•
10/5/2.5/1GBASE-T
autosensing Ethernet
ports
•
10/100/1000BASE-T
autosensing Ethernet
ports
•
SFP+ ports
4-37
Restrictions for using the ports for
IRF connections
All physical ports to be bound to an IRF port
must have the same data rate.
The port must operate at its highest speed.
•
SFP+ port—10 Gbps
•
10/100/1000BASE-T autosensing
port—1 Gbps
•
SFP port—1 Gbps
For a 52-port switch model, the 52 ports are
divided into two groups: ports 1 to 24, port 51,
and port 52 in one group and ports 25 to 50 in
the other group.
To bind multiple ports to an IRF port, make
sure the ports are in the same group. Ports in
one group can be bound to different IRF ports.
All physical ports to be bound to an IRF port
must have the same data rate.
The port must operate at its highest speed.
•
5G/2.5G/1000BASE-T autosensing
port—5 Gbps
•
10/100/1000BASE-T autosensing
port—1 Gbps
•
SFP port—1 Gbps
For a 52-port switch model, the 52 ports are
divided into two groups: ports 1 to 24, port 51,
and port 52 in one group and ports 25 to 50 in
the other group.
To bind multiple ports to an IRF port, make
sure the ports are in the same group. Ports in
one group can be bound to different IRF ports.
All physical ports to be bound to an IRF port
must have the same data rate.
The port must operate at its highest speed.
•
2.5G/1000/100BASE-T autosensing
port—2.5 Gbps
•
SFP+ port—10 Gbps
All physical ports to be bound to an IRF port
must have the same data rate.
The port must operate at its highest speed.
•
10/5/2.5/1GBASE-T autosensing
port—10 Gbps
•
10/100/1000BASE-T autosensing
port—1 Gbps
•
SFP+ port—10 Gbps
For a 52-port switch model, the 52 ports are
divided into two groups: ports 1 to 24, port 51,
and port 52 in one group and ports 25 to 50 in