Nokia ONT Product Manual
  1. Manuals
  2. Brands
  3. Nokia Manuals
  4. Network Router
  5. ONT
  6. Product manual

Nokia ONT Product Manual

Hide thumbs Also See for ONT:
Table of Contents

Advertisement

Quick Links

Nokia ONT
XS-2426G-A Product Guide
3FE-49348-AAAA-TCZZA
Issue 1
December 2020
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements

Advertisement

Table of Contents
loading

Related Manuals for Nokia ONT

Summary of Contents for Nokia ONT

  • Page 1 Nokia ONT XS-2426G-A Product Guide 3FE-49348-AAAA-TCZZA Issue 1 December 2020 Nokia – Proprietary and Confidential Use pursuant to applicable agreements...
  • Page 2 The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2020 Nokia. Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization.

  • Page 3: Table Of Contents

    Nokia ONT Contents About this document............................12 What’s new..............................17 Overview ............................17 What’s new in BBD Release 20.04, Issue 1..................17 ETSI ONT safety guidelines ........................19 Safety instructions..........................19 Safety standards compliance ......................21 Electrical safety guidelines........................21 ESD safety guidelines ........................22 Laser safety guidelines ........................22 Environmental requirements ......................26...
  • Page 4 Install a XS-2426G-A indoor ONT........................61 Overview ............................61 Purpose.............................61 General .............................61 Prerequisites .............................61 Recommended tools .........................61 Safety information ..........................62 Procedure............................62 Replace a XS-2426G-A indoor ONT ......................67 Overview ............................67 Purpose.............................67 General .............................67 Prerequisites .............................67 Recommended tools .........................67 Safety information ..........................68 Procedure............................68 Configure a XS-2426G-A indoor ONT ......................73 Overview ............................73...
  • Page 5 Configuring NTP..........................142 8.43 Configuring USB ..........................143 8.44 Configuring UPnP and DLNA ......................144 8.45 Configuring voice ..........................145 Maintenance ...............................148 8.46 Overview ............................148 8.47 Configuring the password .......................148 Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...
  • Page 6 Viewing log files ..........................159 RG Troubleshooting Counters........................161 8.58 Overview ............................161 8.59 Viewing Residential Gateway (RG) troubleshooting counters............161 ONT configuration file over OMCI ......................165 Overview ............................165 Purpose............................165 Supported configuration file types....................165 ONT configuration file over OMCI ....................167 Nokia – Proprietary and Confidential...
  • Page 7 XS-2426G-A indoor ONT power consumption specifications............53 Table 5-9 XS-2426G-A indoor ONT environmental specifications ..............53 Table 5-10 XS-2426G-A indoor ONT capacity for GEM ports and T-CONTs ...........53 Table 5-11 Package S ONTs ONTENET performance monitoring statistics............54 Table 5-12 Package S ONTs ONTL2UNI performance monitoring statistics ...........54...
  • Page 8 SLID Configuration parameters....................151 Table 8-42 Device Management parameters ....................152 Table 8-43 RG Troubleshooting Counters parameters ..................162 Table 9-1 Supported configuration files......................166 Table 9-2 Download configuration files ......................167 Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...
  • Page 9 Figure 4-3 Laser product label ...........................36 Figure 4-4 Laser classification label........................36 Figure 4-5 Laser warning labels.........................37 Figure 4-6 Sample laser product safety label on the ONT equipment ...............38 Figure 5-1 XS-2426G-A ONT ..........................43 Figure 5-2 XS-2426G-A indoor ONT physical connections (back)..............48 Figure 5-3 XS-2426G-A indoor ONT with fiber optic connector .................49...
  • Page 10 Figure 8-40 DDNS page ..........................141 Figure 8-41 NTP page............................142 Figure 8-42 USB page .............................143 Figure 8-43 UPnP and DLNA page ........................145 Figure 8-44 Voice Setting page........................146 Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...
  • Page 11 Figure 8-52 Reboot Device page ........................156 Figure 8-53 Factory Default page ........................157 Figure 8-54 Diagnostics page ..........................158 Figure 8-55 Log page............................159 Figure 8-56 RG Troubleshooting Counters page .....................162 Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...

  • Page 12: About This Document

    About this document Purpose This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures of this ONT for the current release. Intended audience This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs.
  • Page 13 About this document Nokia ONT Nokia quality processes Nokia’s ONT manufacturing, testing, and inspecting practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ- 30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
  • Page 14 If you are a new user and require access to this service, please contact your Nokia sales representative. Select Products. Type your product name in the Find and select a product field and click the search icon.
  • Page 15 Click Search. Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol. ND OF STEPS Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...
  • Page 16 For details, refer to the Nokia Support portal (https://customer.nokia.com/support/s/). For ordering information, contact your Nokia sales representative. How to comment Note to reviewers: The following "How to comment" text will appear in the final document when it is published. However, the feedback method described below is for use only on final documents.

  • Page 17: What's New

    The Product guide is a new guide in BBD Release 20.04. In future releases, this chapter will provide tables of the feature and document changes applicable to this guide. Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020...
  • Page 18 What’s new Nokia ONT What’s new in BBD Release 20.04, Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 19: Etsi Ont Safety Guidelines

    This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 2.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation.

  • Page 20: Table 2-1 Safety Labels

    Safety-related labels The ONT equipment is labeled with the specific safety instructions and compliance information that is related to a variant of the ONT. Observe the instructions on the safety labels. Table 2-1, “Safety labels” (p. 19) provides sample safety labels on the ONT equipment.

  • Page 21: Safety Standards Compliance

    2.2.4 Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products. If there is an exception to this compliance regulation, you can find this information in the standards compliance section of the unit data sheet in this Product Guide.

  • Page 22: Esd Safety Guidelines

    The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property.

  • Page 23: Figure 2-2 Laser Product Label

    Possibility of equipment damage. Risk of eye damage by laser radiation. 2.5.1 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. Laser warning labels The following figures show the labels related to laser product, classification and warning.

  • Page 24: Figure 2-4 Laser Warning Labels

    ETSI ONT safety guidelines Nokia ONT Laser safety guidelines Figure 2-3 Laser classification label CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1 CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 2-4, “Laser warning labels” (p. 25) shows a laser warning label and an explanatory label for laser products.
  • Page 25 Laser Warning Label 18993 2.5.2 Transmit optical output The maximum transmit optical output of an ONT is +5 dBm. 2.5.3 Normal laser operation In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card.

  • Page 26: Environmental Requirements

    • The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized. • If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.

  • Page 27: Etsi Environmental And Crohs Guidelines

    This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest.

  • Page 28: Figure 3-2 Products Above Mcv Value Label

    The label may be found in this documentation or on the product. Figure 3-2 Products above MCV value label Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.

  • Page 29: Hazardous Substances Table (Hst)

    ONT environmental requirements See the ONT technical specification documentation for more information about temperature ranges. 3.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of ONT equipment must be in Class 1.1, weather-protected, temperature-controlled locations. 3.3.3 Transportation According to EN 300-019-1-2 - Class 2.3, transportation of the ONT equipment must be in packed, public transportation with no rain on packing allowed.

  • Page 30: Figure 3-3 Recycling/Take Back/Disposal Of Product Symbol

    13 August 2005. Figure 3-3 Recycling/take back/disposal of product symbol At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE).

  • Page 31: Ansi Ont Safety Guidelines

    (ONTs or ONUs) in the North American or ANSI market. Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 4.1.1 Safety instruction boxes in customer documentation The safety instruction boxes are provided in the ONT customer documentation.

  • Page 32: Table 4-1 Safety Labels

    4.1.2 Safety-related labels The ONT equipment is labeled with specific safety compliance information and instructions that are related to a variant of the ONT. Observe the instructions on the safety labels. Table 4-1, “Safety labels” (p. 31) provides examples of the text in the various ONT safety labels.

  • Page 33: Safety Standards Compliance

    ANSI ONT safety guidelines Nokia ONT Safety standards compliance Figure 4-1, “Sample safety label on the ONT equipment” (p. 32) shows a sample safety label on the ONT equipment. Figure 4-1 Sample safety label on the ONT equipment Tested to Comply...

  • Page 34: Figure 4-2 Sample Laser Product Label Showing Cdrh 21 Cfr Compliance

    42 for ONTs containing Class 1 Laser modules certified by original manufactures. Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.

  • Page 35: Laser Safety Guidelines

    Possibility of equipment damage. Risk of eye damage by laser radiation. Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.

  • Page 36: Figure 4-3 Laser Product Label

    ANSI ONT safety guidelines Nokia ONT Laser safety guidelines b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.” 4.3.1 Laser warning labels The following figures show sample labels related to laser product, classification and warning.

  • Page 37: Figure 4-6 Sample Laser Product Safety Label On The Ont Equipment

    4.3.2 Laser classification The ONT is classified as a Class 1 laser product based on its transmit optical output. For Class 1 laser products, lasers are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing.

  • Page 38: Electrical Safety Guidelines

    ANSI ONT safety guidelines Nokia ONT Electrical safety guidelines Figure 4-6 Sample laser product safety label on the ONT equipment Model: 3FE55851ABAA MFG: MONTH: XX YEAR: XXXX MAC:XXXXXXXXXXXX ICS: XX MRev: XX SN:ALCLXXXXXXXX I.T.E Intertek CLASS 1 LASER PRODUCT FCC ID: XXXXXXXXXXX...

  • Page 39: Esd Safety Guidelines

    • The door of the ONT not be opened until temperature inside and outside the enclosure has stabilized. • If the door of the ONT must be opened after a rapid change in temperature or humidity, use a dry cloth to wipe down the metal interior to prevent the risk of condensation.
  • Page 40 ANSI ONT safety guidelines Nokia ONT Environmental requirements • When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened. Nokia – Proprietary and Confidential Use pursuant to applicable agreements...

  • Page 41: Xs-2426G-A Unit Data Sheet

    5.12 XS-2426G-A special considerations XS-2426G-A part numbers and identification Table 5-1, “Identification of XS-2426G-A indoor ONTs” (p. 41) provides part numbers and identification information for the XS-2426G-A indoor ONT. Table 5-1 Identification of XS-2426G-A indoor ONTs Ordering kit Provisioning Description...

  • Page 42: Xs-2426G-A General Description

    Table 5-2, “XS-2426G-A power supply ordering information” (p. 42) provides the power supply information for the XS-2426G-A ONT. For more information on power supplies, see the Nokia ONT Power Supply and UPS Guide. Table 5-2 XS-2426G-A power supply ordering information...

  • Page 43: Figure 5-1 Xs-2426G-A Ont

    XS-2426G-A unit data sheet Nokia ONT XS-2426G-A general description Figure 5-1 XS-2426G-A ONT POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WLAN2.4G WLAN5G TEL1 TEL2 VOIP INTERNET USB 36550 XS-2426G-A indoor ONTs provide the following functions: • Dual-band concurrent 2x2 802.11b/g/n/ax 2.4 GHz and 2x2 802.11ac/ax MU-MIMO 5 GHz •...
  • Page 44 • Caller ID, call waiting, call hold, 3-way calling, call transfer, message waiting • Forward Error Correction (FEC) • support for multiple SSIDs (private and public instances); contact your Nokia representative for further details. • Conductive power: 250mW/24dBm (2.4GHz); 500mW/27dBm (5GHz) •...
  • Page 45 • Statistics and troubleshooting • Diagnostic parameters Host object support The ONT provides host object support for: InternetGatewayDeviceLANDevice.Hosts.Host. Port forwarding support The ONT supports the port forwarding of objects via TR-069: • Application Name • WAN Port • LAN Port • Internal Client •...
  • Page 46 “Optics Module Status parameters” (p. 91) Chapter 8, “Configure a XS-2426G-A indoor ONT”. Object support for WiFi parameters The ONT supports the status retrieval and configuration of the following Wi-Fi parameters via TR- 069: • channel • SSID • password for WPA and WEP •...

  • Page 47: Xs-2426G-A Software And Installation Feature Support

    The vendor specific attribute is: X_ALU-COM_XML_File_Name_Path. 5.3.4 TR-104 voice-related alarms The XS-2426G-A ONT supports the following four TR-104 voice-related alarms on a per FXS port basis. These alarms all represent SIP registration failures with an alarm level of MAJOR. • SIPREGDNS: domain name could not be resolved •...

  • Page 48: Xs-2426G-A Interfaces And Interface Capacity

    • SLID entry via Ethernet port • ONT management using an ONT interface XS-2426G-A interfaces and interface capacity Table 5-3, “XS-2426G-A indoor ONT interface connection capacity” (p. 47) describes the supported interfaces and interface capacity for XS-2426G-A indoor ONTs. Table 5-3 XS-2426G-A indoor ONT interface connection capacity...

  • Page 49: Table 5-4 Xs-2426G-A Indoor Ont Physical Connections

    Reset button RESET Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID. WLAN button WLAN Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using the WLAN button.

  • Page 50: Xs-2426G-A Leds

    This connection is provided through 1 USB port on the side of the ONT. The ONT supports external USB hard drives that can be made accessible to all LAN devices. Fiber optic port The SC/APC fiber optic port is located at the back of the ONT and provides the connection for the fiber optic cable. Notes: 1.
  • Page 51 ONT is in the process of ranging or synchronizing over the OLT ONT is ranged but not configured on the OLT ONT is configured on OLT but admin is down and the ONT is out of service ONT is in service and subsequently un-configured on the OLT...

  • Page 52: Xs-2426G-A Detailed Specifications

    IP address; c) the session has been dropped for reasons other than idle timeout. XS-2426G-A detailed specifications Table 5-6, “XS-2426G-A indoor ONT physical specifications” (p. 52) lists the physical specifications for XS-2426G-A indoor ONTs. Table 5-6 XS-2426G-A indoor ONT physical specifications...

  • Page 53: Xs-2426G-A Gem Ports And T-Conts

    Storage: -4°F to 158°F (-20°C to 70°C) XS-2426G-A GEM ports and T-CONTs Table 5-10, “XS-2426G-A indoor ONT capacity for GEM ports and T-CONTs” (p. 53) lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices.

  • Page 54: Xs-2426G-A Performance Monitoring Statistics

    — — Notes: 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds 2. Only packets larger than 9 kB will be counted. Table 5-12 Package S ONTs ONTL2UNI performance monitoring statistics...

  • Page 55: Xs-2426G-A Functional Blocks

    Nokia ONT XS-2426G-A functional blocks Notes: 1. A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 5-13 Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics...

  • Page 56: Xs-2426G-A Standards Compliance

    • G.984.3 support for FEC in both upstream and downstream directions • G.984.3 support for multicast using a single GEM Port-ID for all video traffic • G.984.4 and G.983.2 support for ONT management and provisioning • IEEE 802.1p for traffic prioritization •...
  • Page 57 5.11.1 Energy-related products standby and off modes compliance Hereby, Nokia declares that the XS-2426G-A ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013.

  • Page 58: Xs-2426G-A Special Considerations

    XS-2426G-A indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology.
  • Page 59 • Enable Caller ID and Enable Caller Name ID • Digitmap and the associated Interdigit and Critical timers and Enter key parameters • Warmline timer is enabled per subscriber, but the warmline timer value is configured per ONT and must have a lower value than the Permanent time •...
  • Page 60 XS-2426G-A unit data sheet Nokia ONT XS-2426G-A special considerations Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 61: Install A Xs-2426G-A Indoor Ont

    Purpose This chapter provides the steps to install a XS-2426G-A indoor ONT. General The steps listed in this chapter describe mounting and cabling for a XS-2426G-A indoor ONT. Prerequisites You need the following items before beginning the installation: • all required cables...

  • Page 62: Safety Information

    Observe the following: • The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC.

  • Page 63: Figure 6-1 Xs-2426G-A Ont Connections

    Install a XS-2426G-A indoor ONT Nokia ONT Procedure Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note: The XS-2426G-A cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: •...
  • Page 64 WLAN button. b. Press the WLAN button to change the status of the Wi-Fi service. Verify the ONT LEDs, voltage status, and optical signal levels; see the Nokia ONT Hardware and Cabling Installation Guide. Activate and test the services; see the Nokia ONT Hardware and Cabling Installation Guide.
  • Page 65 Install a XS-2426G-A indoor ONT Nokia ONT Procedure b. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT. ND OF STEPS Nokia – Proprietary and Confidential...
  • Page 66 Install a XS-2426G-A indoor ONT Nokia ONT Procedure Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 67: Replace A Xs-2426G-A Indoor Ont

    Purpose This chapter provides the steps to replace a XS-2426G-A indoor ONT. General The steps listed in this chapter describe mounting and cabling for a XS-2426G-A indoor ONT. Prerequisites You need the following items before beginning the installation: • all required cables...

  • Page 68: Safety Information

    Observe the following: • The indoor ONT should be installed in accordance with the applicable requirements of the NEC or CEC. Local authorities and practices take precedent when there is conflict between the local standard and the NEC or CEC.

  • Page 69: Figure 7-1 Xs-2426G-A Indoor Ont Connections

    Procedure Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). a. Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.
  • Page 70 Attach a fiber dust cover to the end of the SC/APC connector. Replace the old ONT with a new ONT on a flat surface, such as a desk or shelf. Connect the Ethernet cables directly to the RJ-45 ports; see Figure 7-1, “XS-2426G-A indoor...
  • Page 71 If used, configure the SLID; see the Nokia ONT Configuration, Management, and Troubleshooting Guide for more information. Note: A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager.
  • Page 72 Replace a XS-2426G-A indoor ONT Nokia ONT Procedure Activate and test the services; see the Nokia ONT Hardware and Cabling Installation Guide. If necessary, reset the ONT. a. Locate the Reset button on a XS-2426G-A indoor ONT as shown in Figure 7-1, “XS-...

  • Page 73: Configure A Xs-2426G-A Indoor Ont

    Configure a XS-2426G-A indoor ONT Nokia ONT Overview 8 Configure a XS-2426G-A indoor ONT Overview 8.1.1 Purpose 8.1.2 Contents 8.1 Overview GUI configuration 8.2 General configuration 8.3 HGU mode GUI configuration 8.4 Log in to web-based GUI Viewing device information and connection status 8.5 Overview...
  • Page 74 Configure a XS-2426G-A indoor ONT Nokia ONT Overview 8.22 Configuring Wireless 5GHz 8.23 Configuring wireless scheduling 8.24 Configuring IP routing 8.25 Configuring DNS 8.26 Configuring TR-069 8.27 Configuring GRE tunnel 8.28 Configuring Upstream (US) Classifier 8.29 Configuring QoS Security configuration 8.30 Overview...
  • Page 75 Configure a XS-2426G-A indoor ONT Nokia ONT Overview 8.50 Managing the device 8.51 Backing up the configuration 8.52 Restoring the configuration 8.53 Upgrading firmware 8.54 Rebooting the device 8.55 Resetting to factory defaults 8.56 Diagnosing WAN connections 8.57 Viewing log files RG Troubleshooting Counters 8.58 Overview...

  • Page 76: Gui Configuration

    The default gateway IP address must be same as the one printed on the device label. You can connect to this IP address using your web browser after connecting your PC to one of Ethernet ports of the ONT. The static IP address of your PC must be in the same default gateway subnet as the ONT.

  • Page 77: Figure 8-1 Web Login Page

    Note: To help protect the security of your Internet connection, the application displays a pop-up reminder to change both the Wi-Fi password and the ONT password. To increase password security, use a minimum of 10 characters, consisting of a mix of numbers and upper and lower case letters.

  • Page 78: Viewing Device Information And Connection Status

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Overview Viewing device information and connection status Overview 8.5.1 Purpose This chapter describes procedures to view device information and connection status on the XS- 2426G-A. 8.5.2 Contents 8.5 Overview...

  • Page 79: Table 8-1 Device Information Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing device information Figure 8-2 Device Information page Note: Upon login, the 10G PON Home Gateway page displays the WAN status block on the bottom left part of each page. This block shows the WAN connection ID, the WAN status, and any WAN errors.

  • Page 80: Viewing Lan Status

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing LAN status Viewing LAN status Click Status LAN Status from the left pane in the 10G PON Home Gateway page. The LAN Status page displays the following information.

  • Page 81: Viewing Wan Status

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing WAN status Table 8-2 LAN Status parameters Field Description Wireless Information Wireless Status Indicates whether the wireless is on or off Wireless Channel Wireless channel number...

  • Page 82: Table 8-3 Wan Status Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing WAN status Figure 8-4 WAN Status page Table 8-3 WAN Status parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.

  • Page 83: Viewing Wan Ipv6 Status

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing WAN IPv6 status Table 8-3 WAN Status parameters (continued) Field Description Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server Manual DNS Manual Domain Name Server...

  • Page 84: Table 8-4 Wan Status Ipv6 Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing WAN IPv6 status Figure 8-5 WAN Status IPv6 page Table 8-4 WAN Status IPv6 parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.

  • Page 85: Viewing Sta Information

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing STA information Table 8-4 WAN Status IPv6 parameters (continued) Field Description PON Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection...

  • Page 86: Table 8-5 Sta Information Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing STA information Figure 8-6 STA Information page Table 8-5 STA information parameters Field Description MAC ADDRESS MAC address of the Ethernet connection SSID NAME Name of each SSID...

  • Page 87: Viewing Neighboring Access Points

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing Neighboring Access Points 8.11 Viewing Neighboring Access Points Click Status Neighboring AP from the left pane in the 10G PON Home Gateway page. The Neighboring Access Points page displays the following information.

  • Page 88: Viewing Home Networking Information

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing home networking information Table 8-6 Neighboring AP parameters (continued) Field Description Wi-Fi Mode Indicates the Wi-Fi mode Network Type Indicates the network type Click Scan. ND OF STEPS 8.12...

  • Page 89: Table 8-7 Home Networking Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing home networking information Figure 8-8 Home Networking page Table 8-7 Home Networking parameters Field Description Local Interface Ethernet Table displays the number of Ethernet connections and their settings Nokia –...

  • Page 90: Viewing Optics Module Status

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing optics module status Table 8-7 Home Networking parameters (continued) Field Description Wireless Table displays the number of wireless connections and their settings (2.4GHz and 5GHz) Wireless Settings (2.4GHz and 5GHz)

  • Page 91: Viewing Statistics

    Optics module voltage, measured in V Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module temperature, measured in C Rx Optics Signal Level at 1577 nm (ONT ANI-ONT-Side Optical Received optics signal level at 1577 nm, measured in Measurements) Tx Optics Signal Level at 1270nm (ONT ANI-ONT-Side Optical...

  • Page 92: Figure 8-10 Lan Statistics Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing statistics Figure 8-10 LAN Statistics page Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 93: Figure 8-11 Wan Statistics Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing statistics Figure 8-11 WAN Statistics page Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...

  • Page 94: Viewing Voice Information

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing voice information Figure 8-12 WLAN Statistics page You can click Refresh to display up-to-date information. ND OF STEPS 8.15 Viewing voice information Click Status Voice Information from the left pane in the 10G PON Home Gateway page. The Voice Information page displays the following information: Nokia –...

  • Page 95: Table 8-9 Voice Information Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing voice information Figure 8-13 Voice Information page Table 8-9 Voice Information parameters Field Description Line Select a line from the list. The default is Line 1.
  • Page 96 Configure a XS-2426G-A indoor ONT Nokia ONT Viewing device information and connection status Viewing voice information Table 8-9 Voice Information parameters (continued) Field Description Register Error Reason SIP standard error reason for the register status This field is blank if the register is set to OK...

  • Page 97: Network Configuration

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Overview Network configuration 8.16 Overview 8.16.1 Purpose This chapter describes the network configuration tasks supported by XS-2426G-A ONTs. 8.16.2 Contents 8.16 Overview 8.17 Configuring LAN 8.18 Configuring LAN IPv6 8.19 Configuring WAN 8.20 Configuring WAN DHCP...

  • Page 98: Figure 8-14 Lan Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring LAN Figure 8-14 LAN page Configure the following LAN parameters: Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 99: Configuring Lan Ipv6

    Select the port mode for each port and click Save. • Route Mode • Bridge Mode IPv4 Address Enter the IPv4 address of the ONT. Subnet Mask Enter the subnet mask of the ONT. DHCP enable Select this checkbox to enable DHCP.

  • Page 100: Table 8-11 Lan Ipv6 Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring LAN IPv6 Figure 8-15 LAN IPv6 page Configure the following parameters: Table 8-11 LAN IPv6 parameters Field Description IPv6 LAN Host Configuration DNS Server Select a DNS server from the list.

  • Page 101: Configuring Wan

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring WAN Table 8-11 LAN IPv6 parameters (continued) Field Description DHCPv6 Server Pool DHCP Start IP Address Enter the starting DHCP IP address. DHCP End IP Address Enter the ending DHCP IP address.

  • Page 102: Table 8-12 Wan Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring WAN Figure 8-16 WAN page Configure the following parameters: Table 8-12 WAN parameters Field Description WAN Connection List Select a WAN connection from the list to set the connection parameters.

  • Page 103: Configuring Wan Dhcp

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring WAN DHCP Table 8-12 WAN parameters (continued) Field Description VLAN PRI Enter the VLAN PRI. WAN IP Mode Select an IP mode from the list. Manual DNS Enter the manual Domain Name Server.

  • Page 104: Configuring Wireless 2.4Ghz

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 2.4GHz Table 8-13 WAN DHCP parameters Field Description WAN Connection List Select a WAN connection from the list. DHCP Option 50 Persistent Select this checkbox to enable DHCP Option 50 persistent.

  • Page 105: Figure 8-18 Wireless (2.4Ghz) Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 2.4GHz Figure 8-18 Wireless (2.4GHz) page Configure the following parameters: Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...

  • Page 106: Table 8-14 Wireless (2.4Ghz) Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 2.4GHz Table 8-14 Wireless (2.4GHz) parameters Field Description Enable Select this checkbox to enable Wi-Fi. Mode Select a Wi-Fi mode from the list: • auto (b/g/n/ax) • b • g •...

  • Page 107: Configuring Wireless 5Ghz

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 5GHz Table 8-14 Wireless (2.4GHz) parameters (continued) Field Description Encryption Mode Select an encryption mode from the list: • OPEN • WEP • WPA/WPA2 Personal • WPA/WPA2 Enterprise • WPA2/WPA3 Personal •...

  • Page 108: Table 8-15 Wireless (5Ghz) Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 5GHz Figure 8-19 Wireless (5GHz) page Configure the following parameters: Table 8-15 Wireless (5GHz) parameters Field Description Enable Select this checkbox to enable Wi-Fi. Nokia – Proprietary and Confidential...
  • Page 109 Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Wireless 5GHz Table 8-15 Wireless (5GHz) parameters (continued) Field Description Bandwidth Select the bandwidth range from the list: • 20 MHz • 40 MHz • 80 MHz Channel Select a channel from the list or select Auto to have the channel automatically assigned.

  • Page 110: Configuring Wireless Scheduling

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring wireless scheduling Click Save. You can click Refresh to update displayed information. ND OF STEPS 8.23 Configuring wireless scheduling Click Network Wireless Schedule from the left pane in the 10G PON Home Gateway page.

  • Page 111: Configuring Ip Routing

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring IP routing Enter a start time and end time for the period in which you want the wireless signal off. Select Everyday or Individual Days from the list. If you select Individual Days, select the checkboxes for the desired days.

  • Page 112: Table 8-16 Ip Routing Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring IP routing Figure 8-21 IP Routing page Configure the following parameters: Table 8-16 IP Routing parameters Field Description Enable Routing Select this checkbox to enable routing. Destination IP Address Enter the destination IP address.

  • Page 113: Configuring Dns

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring DNS You can click Refresh to update the displayed information. ND OF STEPS 8.25 Configuring DNS Click Network DNS from the left pane in the 10G PON Home Gateway page. The DNS page displays.

  • Page 114: Configuring Tr-069

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring TR-069 Table 8-17 DNS parameters (continued) Field Description Origin Domain Enter the origin domain name. New Domain Associate an origin domain with a new domain and click Add. You can click Delete to delete a particular Domain Name.

  • Page 115: Configuring Gre Tunnel

    Password Enter the password used to log in to the auto-configuration server. Connect Request Username Enter the username used to log in to the ONT. Connect Request Password Enter the password used to log in to the ONT. Click Save.

  • Page 116: Table 8-19 Gre Tunnel Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring GRE tunnel Figure 8-24 GRE Tunnel page Configure the following parameters: Table 8-19 GRE Tunnel parameters Field Description Tunnel Name Select Create new GRE Tunnel or select an existing tunnel from the list.

  • Page 117: Configuring Upstream (Us) Classifier

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Upstream (US) Classifier Click Save. You can click Delete to delete the entries. ND OF STEPS 8.28 Configuring Upstream (US) Classifier The US Classifier feature is used to create policies, classifiers, and classifier rules for upstream traffic handling.

  • Page 118: Table 8-20 Us Classifier Policy Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Upstream (US) Classifier Configure the following parameters: Table 8-20 US Classifier Policy parameters Field Description Tunnel Type The tunnel type is set to GRE and cannot be modified. Tunnel Interface Select a tunnel interface from the list: No Tunnel, GRE Tunnel, or LAN traffic.

  • Page 119: Table 8-21 Us Classifier Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Upstream (US) Classifier Figure 8-26 US Classifier page Configure the following parameters: At least one field must be selected to create a classifier. A maximum of four fields may be selected to create a classifier;...

  • Page 120: Figure 8-27 Us Classifier Rules Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring Upstream (US) Classifier Click Save. You can click Reset to reset the configured values. To delete a classifier, click Delete for the applicable classifier in the classifier table. A classifier can only be deleted if it is not associated with any classifier rules.

  • Page 121: Configuring Qos

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring QoS Table 8-22 US Classifier Rules parameters Field Description Policy Select a policy from the list. Classifier Select a classifier from the list. Interface Select an interface from the list; for example, None, LAN, 2.4G SSID, 5G SSID.

  • Page 122: Figure 8-28 Qos Config Page (L2 Packet Sizes)

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring QoS Figure 8-28 QoS Config page (L2 packet sizes) Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 123: Figure 8-29 Qos Config Page (L3 Packet Sizes)

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring QoS Figure 8-29 QoS Config page (L3 packet sizes) Configure the following parameters: Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 Issue 1 3FE-49348-AAAA-TCZZA...

  • Page 124: Table 8-23 Qos Config Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Network configuration Configuring QoS Table 8-23 QoS Config parameters Field Description QoS Setting Type Select a QoS service layer type from the list L2 Criteria or L3 Criteria. Classification Criteria Source MAC Enter the source MAC address.

  • Page 125: Security Configuration

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Overview Security configuration 8.30 Overview 8.30.1 Purpose This chapter describes the security configuration tasks supported by XS-2426G-A ONTs 8.30.2 Contents 8.30 Overview 8.31 Configuring the firewall 8.32 Configuring the MAC filter 8.33 Configuring the IP filter...

  • Page 126: Configuring The Mac Filter

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring the MAC filter Figure 8-30 Firewall page Configure the following parameters. Table 8-24 Firewall parameters Field Description Security level Select the security level from the list: High: Traffic denied inbound and minimally permit common services outbound...

  • Page 127: Table 8-25 Mac Filter Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring the MAC filter Figure 8-31 MAC Filter page Configure the following parameters: Table 8-25 MAC Filter parameters Field Description Ethernet Interface MAC Filter Mode Select the MAC filter mode from the list: Blocked or Allowed.

  • Page 128: Configuring The Ip Filter

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring the IP filter Table 8-25 MAC Filter parameters (continued) Field Description MAC Filter Mode Select the MAC filter mode from the list: Blocked or Allowed. SSID Select Select the SSID from the list.

  • Page 129: Configuring The Url Filter

    • Drop for downstream Internal Client Select an internal client from the list: • Custom settings: uses the IP address input below • IP: uses the connecting devices' IP to the ONT Local IP Address Enter the local IP address. Local Subnet Mask Enter the local subnet mask.

  • Page 130: Table 8-27 Url Filter Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring the URL filter Figure 8-33 URL Filter page Note: You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Configure the following parameters: Table 8-27 URL Filter parameters...

  • Page 131: Configuring Parental Control

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring parental control 8.35 Configuring parental control Click Security Parent Control from the left pane in the 10G PON Home Gateway page. The Parental Control page displays. Figure 8-34 Parental Control page You can click Delete to delete the group.

  • Page 132: Table 8-28 Parental Control Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring parental control Figure 8-35 Create new group page Click Add. You can click on each field such as Device, Access Internet, URL, Schedule, and Bed Time to configure the related parameters.

  • Page 133: Configuring Dmz And Alg

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring DMZ and ALG Table 8-28 Parental control parameters (continued) Field Description Group Name Displays the selected group name Device Device MAC Address Enter the MAC address and click Add Device.

  • Page 134: Table 8-29 Alg Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring DMZ and ALG Figure 8-36 DMZ and ALG page Configure the following parameters: Table 8-29 ALG parameters Field Description ALG Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP.

  • Page 135: Configuring Access Control

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring access control Click Save DMZ. ND OF STEPS 8.37 Configuring access control This procedure describes how to configure the access control level (ACL). Note: ACL takes precedence over the firewall policy.

  • Page 136: Table 8-31 Access Control Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Security configuration Configuring access control Table 8-31 Access Control parameters Field Description Select a connection from the list. Trusted Network Enable Click to enable or disable trusted network. ICMP, Telnet, SSH, HTTP, TR-069, HTTPS,...

  • Page 137: Configuring The Application

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Overview Configuring the Application 8.38 Overview 8.38.1 Purpose This chapter describes the application configuration tasks supported by the XS-2426G-A ONTs. 8.38.2 Contents 8.38 Overview 8.39 Configuring port forwarding 8.40 Configuring port triggering 8.41 Configuring DDNS...

  • Page 138: Table 8-33 Port Forwarding Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring port forwarding Figure 8-38 Port Forwarding page Configure the following parameters: Table 8-33 Port Forwarding parameters Field Description Application Name Select an application name from the list. The default is Custom settings.

  • Page 139: Configuring Port Triggering

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring port triggering Click Add. ND OF STEPS 8.40 Configuring port triggering Click Application Port Triggering from the left pane in the 10G PON Home Gateway page. The Port Triggering page displays.

  • Page 140: Configuring Ddns

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring DDNS Table 8-34 Port Triggering parameters (continued) Field Description Triggering Port Enter the triggering port range. Expire Time Enter the expiration time in seconds. Open Protocol Select the open port protocol from the list: •...

  • Page 141: Table 8-35 Ddns Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring DDNS Figure 8-40 DDNS page Configure the following parameters: Table 8-35 DDNS parameters Field Description WAN Connection List Select a WAN connection from the list. Enable DDNS Select this checkbox to enable DDNS on the selected WAN connection.

  • Page 142: Configuring Ntp

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring NTP 8.42 Configuring NTP Click Application NTP from the left pane in the 10G PON Home Gateway page. The NTP page displays. Figure 8-41 NTP page Configure the following parameters:...

  • Page 143: Configuring Usb

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring USB Click Save. You can click Refresh to update the displayed information. ND OF STEPS 8.43 Configuring USB You can connect USB storage devices and USB printers to the USB ports of the device. The USB menu enables you to configure FTP and SFTP for your USB storage devices.

  • Page 144: Configuring Upnp And Dlna

    Re-enter the password for the SFTP server. Connected USB Devices Table For each printer that is connected to the ONT, the following fields are displayed: • Host Number for example: Printer1, Printer2 • Device Name: name or identification for the USB device •...

  • Page 145: Configuring Voice

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring voice Figure 8-43 UPnP and DLNA page Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. Click Save/Apply. ND OF STEPS 8.45 Configuring voice Click Application Voice Setting from the left pane in the 10G PON Home Gateway page.

  • Page 146: Table 8-38 Voice Setting Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring voice Figure 8-44 Voice Setting page Configure the following parameters: Table 8-38 Voice Setting parameters Field Description Voice Setting Outbound Proxy Enter the SIP outbound proxy. Outbound Proxy Port Enter the outbound proxy port.
  • Page 147 Configure a XS-2426G-A indoor ONT Nokia ONT Configuring the Application Configuring voice Table 8-38 Voice Setting parameters (continued) Field Description Proxy Server Enter the proxy server. Proxy Server Port Enter the proxy server port. Registrar Server Enter the registrar server.

  • Page 148: Maintenance

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Overview Maintenance 8.46 Overview 8.46.1 Purpose This chapter describes the maintenance tasks supported by XS-2426G-A ONTs. 8.46.2 Contents 8.46 Overview 8.47 Configuring the password 8.48 Configuring LOID 8.49 Configuring SLID 8.50 Managing the device 8.51 Backing up the configuration...

  • Page 149: Table 8-39 Password Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Configuring the password • the first character cannot be a special character • there are not enough character classes Click Maintenance Password from the left pane in the 10G PON Home Gateway page. The Password page displays.

  • Page 150: Configuring Loid

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Configuring LOID 8.48 Configuring LOID Click Maintenance → LOID Config from the left pane in the 10G PON Home Gateway page. The LOID Config page displays. Figure 8-46 LOID Config page Configure the following parameters:...

  • Page 151: Table 8-41 Slid Configuration Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Configuring SLID Click Maintenance SLID Configuration from the left pane in the 10G PON Home Gateway page. The SLID Configuration page displays. Figure 8-47 SLID Configuration page Configure the following parameters: Table 8-41 SLID Configuration parameters...

  • Page 152: Managing The Device

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Managing the device 8.50 Managing the device Click Maintenance Device Management from the left pane in the 10G PON Home Gateway page. The Device Management page displays. Figure 8-48 Device Management page...

  • Page 153: Backing Up The Configuration

    Click Maintenance Backup and Restore from the left pane in the 10G PON Home Gateway page. The Backup and Restore page displays. Figure 8-49 Backup and Restore page Click Export to export the current ONT configuration to a backup file. ND OF STEPS 8.52...

  • Page 154: Upgrading Firmware

    Maintenance Upgrading firmware Figure 8-50 Backup and Restore page Click Choose file and select the backup file. Click Import to restore the ONT to the saved backup. ND OF STEPS 8.53 Upgrading firmware Click Maintenance Firmware Upgrade from the left pane in the 10G PON Home Gateway page.

  • Page 155: Rebooting The Device

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Rebooting the device Figure 8-51 Firmware Upgrade page Click Choose file and select the firmware file. Click Upgrade to upgrade the firmware. ND OF STEPS 8.54 Rebooting the device Click Maintenance Reboot Device from the left pane in the 10G PON Home Gateway page.

  • Page 156: Resetting To Factory Defaults

    Nokia ONT Maintenance Resetting to factory defaults Figure 8-52 Reboot Device page Click Reboot to reboot the ONT. ND OF STEPS 8.55 Resetting to factory defaults Click Maintenance Factory Default from the left pane in the 10G PON Home Gateway page.

  • Page 157: Diagnosing Wan Connections

    Nokia ONT Maintenance Diagnosing WAN connections Figure 8-53 Factory Default page Click Factory Default to reset the ONT to its factory default settings. ND OF STEPS 8.56 Diagnosing WAN connections Click Maintenance Diagnostics from the left pane in the 10G PON Home Gateway page.

  • Page 158: Figure 8-54 Diagnostics Page

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Diagnosing WAN connections Figure 8-54 Diagnostics page Select a WAN connection to diagnose from the list. Enter the IP address or domain name. Select the test type: ping, traceroute, or both. Enter the number of ping attempts to perform (1 - 1000); the default is 4.

  • Page 159: Viewing Log Files

    Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Viewing log files Click Start Test. The results will be displayed at the bottom of the page. Click Cancel to cancel the test. ND OF STEPS 8.57 Viewing log files Click Maintenance Log from the left pane in the 10G PON Home Gateway page. The Log page displays.
  • Page 160 Configure a XS-2426G-A indoor ONT Nokia ONT Maintenance Viewing log files • Warning • Notice • Informational • Debug Select a reading level from the list to determine which types of events to display from the log file: • Emergency •...

  • Page 161: Rg Troubleshooting Counters

    Configure a XS-2426G-A indoor ONT Nokia ONT RG Troubleshooting Counters Overview RG Troubleshooting Counters 8.58 Overview 8.58.1 Purpose This section describes the RG troubleshooting counters GUI procedures. 8.58.2 Contents 8.58 Overview 8.59 Viewing Residential Gateway (RG) troubleshooting counters 8.59 Viewing Residential Gateway (RG) troubleshooting counters The Troubleshooting Counters feature enables service providers and end users to monitor the performance of their broadband connection.

  • Page 162: Table 8-43 Rg Troubleshooting Counters Parameters

    Configure a XS-2426G-A indoor ONT Nokia ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Figure 8-56 RG Troubleshooting Counters page Configure the following parameters: Table 8-43 RG Troubleshooting Counters parameters Field Description WAN Connection List Select a WAN connection from the list.
  • Page 163 Configure a XS-2426G-A indoor ONT Nokia ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Table 8-43 RG Troubleshooting Counters parameters (continued) Field Description Internet Status Indicates whether the broadband connections is active (UP) or not (DOWN). Latency This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple times.
  • Page 164 Configure a XS-2426G-A indoor ONT Nokia ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020 3FE-49348-AAAA-TCZZA Issue 1...

  • Page 165: Ont Configuration File Over Omci

    This procedure describes how to use configuration files over OMCI to configure ONTs. Some advantages include: • flexibility to change the ONT default behavior by downloading configuration file • flexibility to update a deployed ONT by downloading updated parameters • ability to securely download any configuration file to an ONT •...
  • Page 166 XML file. Nokia recommends using this procedure, rather than embedded voice XML files. The Nokia defined index for the Voice XML file is: "XML" Nokia – Proprietary and Confidential Use pursuant to applicable agreements December 2020...

  • Page 167: Ont Configuration File Over Omci

    9.3.1 Filename conventions Nokia provides the raw configuration files, which must be saved by the operator in a TAR file to be uploaded. TAR file names must be unique. The filenames of the raw configuration files may not adhere to the naming conventions outlined below.
  • Page 168 The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl) ND OF STEPS The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Nokia defined index.
  • Page 169 If pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT. b. If pland-cfgfileX=FILENAME1 and dnload-cfgfileX= Disabled , FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required. c. If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 Nokia –...
  • Page 170 The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl) ND OF STEPS The ONT will distribute the configuration files to the different services based on the active indication from the OLT and on the Nokia defined index.

This manual is also suitable for:

Xs-2426g-a

Table of Contents

Save PDF