Model 15000-18000 Installation, Operation and Maintenance ERTICAL LEARANCE EAD ENTIRE MANUAL BEFORE ASSEMBLING INSTALLING OPERATING OR SERVICING THIS Check the height of the area where the lift is to be EQUIPMENT installed. Clearance should be calculated based on ROPER MAINTENANCE AND INSPECTION IS NECESSARY the full raised height of the lift.
Model 15000-18000 Installation, Operation and Maintenance ECEIVING MPORTANT Always wear safety glasses while installing lift. OOLS MINIMUM REQUIRED The shipment should be thoroughly inspected as soon as it is received. The signed bill of lading is a. Tape measure, 16ft acknowledgement by the carrier of receipt in good b.
Page 5
Model 15000-18000 Installation, Operation and Maintenance VERHEAD NCHORING 12) Before raising overhead into position install 4 5) The anchor bolts must be installed at least 8” each (2 per column) hex flange bolts and nuts in from any crack, edge, or expansion joint.
Page 6
Model 15000-18000 Installation, Operation and Maintenance 14) Install Overhead Limit Switch to the Overhead 16) Assemble the cable trapping hardware with a Beam using the rear set of holes on the Power 3/8”-16 x 3” Lg bolt with (2) 3/8”-16 flange nuts at Side of the lift.
Page 7
Model 15000-18000 Installation, Operation and Maintenance & H YNCHRONIZER ABLES OWER YDRAULIC INES 17) Manually raise the carriages to a common lock 19) Mount Power Unit to power column as shown in position, to gain access to the top of the Fig.
Page 8
Model 15000-18000 Installation, Operation and Maintenance 21) Thread 9/16”-18 O-ring elbow ( ) into 23) Hoses should connect to cylinders with a 90 in hardware box power unit. Attach free end of power unit hose degree elbow rotated 25 degrees upward and to elbow.
Page 9
Model 15000-18000 Installation, Operation and Maintenance 30) Make sure all the arm bolts are tight using a 3/8” hex key. Slide all the arms out so they are fully extended making sure that the male is retained in the female.
Page 10
Model 15000-18000 Installation, Operation and Maintenance 45) Return all provided literature (including this INAL DJUSTMENTS YDRAULICS manual) to the literature pack envelope and 36) Lower the lift to the floor and raise the lift deliver the envelope to the approximately one foot.
Page 11
Model 15000-18000 Installation, Operation and Maintenance Wiring Diagram FOR SINGLE PHASE FIELD CONECTIONS (Normally Open) FIELD CONECTIONS FOR THREE PHASE FACTORY WIRED FOR 208−240V RECONNECTIONS FOR 440−480V Fig 17 – Electrical Wiring Diagram Page 11 Rev. 2/14/19 15-18000-IOM-A.doc...
Model 15000-18000 Installation, Operation and Maintenance Maintenance; and in the case of frame engaging lift, PERATION ROCEDURE ALI/LP-GUIDE, Vehicle Lifting Points/Quick AFETY OTICES AND ECALS Reference Guide for Frame Engaging Lifts; in a conspicuous location in the lift area convenient to This product is furnished with graphic safety the operator.
Page 13
Test the stability of the vehicle by Check adapters for damage or excessive wear. attempting to rock the vehicle. Check adapters for Replace as required with genuine Challenger Lifts secure contact with vehicle lift points. If the vehicle parts.
12117H COLUMN EXTENSION PACK (16’-6” O.A. Ht.) Items (2, 50, 64, 65, 66, 67) Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.
Page 15
Model 15000-18000 Installation, Operation and Maintenance PARTS BREAKDOWN (continued) Fig B. Lock-Power/Idler Page 15 Rev. 2/14/19 15-18000-IOM-A.doc...
Page 16
SNAP ON LOCK COVER 37032 1/8” UNION TEE PUSH-LOCK Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.
Page 17
3/8” -16 x 3/4” LG. HEX FLANGE BOLT A1154 3/8” -16 HEX FLANGE NUT Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.
Page 18
12019 SYNC. CABLE ASSEMBLY (16’-6” O.A. Ht.) Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.
Page 19
ARM ASSEMBLY – 15/18K Items (42, 77, 78, 79, 80, 81, 82,88) Replace all worn, damaged, or broken parts with parts approved by Challenger Lifts Inc. or with parts meeting Challenger Lifts Inc. specifications. Contact your local Challenger Lifts Parts Distributor for pricing and availability.