Unit Position - Connection Diagram - Intec MGC2-12 User Manual

PolyGard Multi-Point Controller
®
User Manual - MGC2-12
4.2 Unit position – Connection diagram
Green/Ye G
Gray X
Gray H
120 VAC
Blue N
Input Power
Green/Ye G
(see ill. 1)
R01
1
1 2
X1
Fault Fault
X10
1 2 3 4 5 6 7 8 9 101112
Sensor
Inputs
(see ill. 4)
(see ill. 2)
Binary - Relay Outputs
R06 R07 R08 R09 R10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2
X1 X2
EP-02-1
X10 X11
1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112
(see ill. 4)
Sensor
Inputs
Terminal 1 24 VDC
block "X1" 2 Output
Circuit breaker
1F1
(see ill. 3)
Power Unit
Top
120 VAC Input Power Supply
AC hot
AC neutral
Earth ground
H N G
Terminal block
Polygard® is a registered trademark of MSR
Customer Services (858) 578-7887 & (888) GO INTEC
INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064
(see ill. 2)
Binary - Relay Outputs
R02 R03 R04 R05
2 3 4 5 6 7 8 9 10 11 12 13 14 15
X2
Alarm Alarm
INTEC Controls
0 5 . 0 7 . 1 0 1 0 : 2 8 a m
DIN Rail
X11
1 2 3 4 5 6 7 8 9 101112
Optional:
Modbus Interface
Digital Analog
(see ill. 8)
Inputs Outputs
(see ill. 5) (see ill. 6) (see ill. 2)
Binary - Relay Outputs
R11 R12 R13 R14 R15
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
1 2
X1 X2
EP-02-2
X10 X11
1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112
Analog Sensor Analog
Outputs Inputs Outputs
(see ill. 6) (see ill. 4) (see ill. 6)
Horn
Bottom
120 VAC (90...230 VAC), 50/60 Hz
• "Min wire size 16 AWG (1.5 mm
• Resettable breaker, max 10 A,
rated current approx. 2 A
Fax (858) 578-4633 & (888) FX INTEC
1 2 3 4 5 6 7 8
X2
C5 Comm.
Coupler
Optional:
BACnet
X1
1 2 3 4
(see ill. 7)
DIN Rail
ill. 8
Modbus Interface, optional
(Located at Controller module)
)"
2
ill. 1
www.inteccontrols.com
Page 25
C5 BACnet Communication
Coupler, optional
RJ45
Upwards BACnet
communication
to BAS
ill. 7
1 2 3 4 5 6 7 8 9 10 11 12
Specification subject to change without notice.
Printed in USA 131119
X11
MGC2-12