Texecom Premier Elite Series Installation Manual page 94

UDL & Digi Options
The plug-on communicator can be programmed to dial up to 3 sets
of Alarm Receiving Centre (ARC) information. Each 'Set' consists of the
following options:
Protocol
This is the reporting protocol that is used to communicate with the
Alarm Receiving Centre. The following protocols are supported:
•
Fast Format: The panel will report using Fast Format. If this
option is selected the
programmed (see below)
•
Contact ID: The panel will report using Contact ID. If this option
is selected, the 'Reporting Areas' must be programmed (see
below)
•
SIA Level II: The panel will report using SIA Level II
•
EasyCom Pager: The panel will report to an EasyCom type pager
•
SMS Messaging: The panel will send Short Message Service
(SMS) text messages to a mobile phone
•
Speech Module: The panel will use the speech module and play
recorded voice messages to the programmed numbers.
•
Texecom Connect: The panel will be compatible with the Texecom
Connect app. The SmartCom IP should be programmed before the
Connect protocol is enabled.
other changes will be made to the panel.
Primary & Secondary IP addresses and Port Numbers will
o
be programmed for the Connect servers. Port numbers are
assigned based on Country Code to enable additional
features such as local Time synchronisation.
Dial attempts will be set at 9
o
Connect Via IP will be enabled
o
The comport that a ComIP or ComWiFi is connected to,
o
programmed and enabled will be selected.
Add Push Message will be enabled
o
Reporting options will be enabled and selected. (these may
o
be altered, however Priority Alarms, Alarms and Open/Close
MUST be selected to allow the app to correctly function.)
All areas will be selected for Reporting
o
The "Poll IP every" Timer will be set to 15 Minutes.
o
Primary Telephone Number
This is the first telephone number that the communicator will dial for
the Alarm Receiving Centre or the first mobile telephone number to
send SMS to. Each telephone number can be up to 24 digits.
Secondary Telephone Number
This is the second telephone number that the communicator will dial
for the Alarm Receiving Centre or the second mobile telephone
number to send SMS to. Each telephone number can be up to 24
digits.
Account Number
This is the account number that will be reported to the Alarm Receiving
Centre. Each account number can be up to 6 digits. (Not Required for
Texecom Connect)

Each area can also have its own account number (see page
96 & 81 for details).
Dialling Attempts
This is the number of times the communicator will try to dial the Alarm
Receiving Centre or Pager telephone number.

The number of dialling attempts is limited to 9. If this value is set
to 0, the communicator will never dial out.
94
'Reporting Channels' must
When selected for an ARC several
The following option is only displayed if the
Fast Format protocol is selected
R eporting on
2 B 2 B 2 B
This option defines which channels report to the selected Alarm
Receiving Centre.
R estoring on
3 B 3 B 3 B
This option defines which channels report a restore to the selected
Alarm Receiving Centre.
be
O pen/Close on
4 B 4 B 4 B
This option defines which channels report Open/Close to the selected
Alarm Receiving Centre.
The following option is only displayed if Contact ID
or SIA Level II protocols are selected
R eporting Areas
5 B 5 B 5 B
This option defines which areas report events to the selected
Alarm Receiving Centre.
The following option is only displayed if Contact ID, SIA
Level II or EasyCom Pager protocols are selected
R eports
6 B 6 B 6 B
This option defines which events report to the Alarm Receiving
Centre when using Contact ID or SIA Level II.
P - Priority Alarm and Cancel Events
7 B 7 B 7 B
The system will report Priority alarm and cancel events to the
selected Alarm Receiving Centre.
A - Normal Alarm and Cancel Events
8 B 8 B 8 B
The system will report alarm and cancel events to the selected
Alarm Receiving Centre.
O - Open and Close Events
9 B 9 B 9 B
The system will report open and close events to the selected
Alarm Receiving Centre.
B - Omit and Reinstate Events
1 0 B 1 0 B 1 0 B
The system will report omit and reinstate events to the selected
Alarm Receiving Centre.
M - Maintenance Alarm Events
1 1 B 1 1 B 1 1 B
The system will report maintenance alarm events to the selected
Alarm Receiving Centre.
T - Tamper Alarm Events
1 2 B 1 2 B 1 2 B
The system will report tamper alarm events to the selected Alarm
Receiving Centre.
C - Test Call Events
1 3 B 1 3 B 1 3 B
The system will report test call events to the selected Alarm
Receiving Centre.
R - Restore Events
1 4 B 1 4 B 1 4 B
The system will report restore events to the selected Alarm
Receiving Centre.
Protocol Options
Not available if EasyCom Pager is selected
Config.
This option defines which secondary options are enabled.
A - Area Account
1 6 B 1 6 B 1 6 B
Events are reported to the Alarm Receiving Centre using the area
account numbers (see page 96 for details).
S - SIA Level I / UCP
1 7 B 1 7 B 1 7 B
Events are reported to the Alarm Receiving Centre using SIA Level I
or or to an SMS Messaging Server using UCP.
R - Enable Radio-Pad
1 8 B 1 8 B 1 8 B
The system will use the Paknet radio-pad to report events to the
selected Alarm Receiving Centre.
Premier Elite Series Installation Manual
INS176-15