Dvs Group - Yaesu FTDX5000 Series Operating Manual

M M
ENU ODE
013 DISP S PK HLD
Function: Selects the peak hold time of the VFO-B
receiver's S-meter.
Available Values: OFF / 0.5s / 1.0s / 2.0s
Default Setting: OFF
014 DISP RTR STU
Function: Selects the starting point of your rotator
controller's indicator needle.
Available Values: 0° / 90° / 180° / 270°
Default Setting: 0°
015 DISP RTR ADJ
Function: Adjusts the indicator needle precisely to the
starting point set in menu item "014 DISP RTR STU".
Available Values: –30° ~ 0° (2°/step)
Default Setting: 0°
016 DISP QMB MKR
Function: Enables/Disables the QMB Marker (White ar-
row "") to display on the Spectrum Band Scope when
the optional DMU-2000 Data Management Unit is con-
nected.
Available Values: DISABLE / ENABLE
Default Setting: ENABLE
A :
DVICE
If the optional DMU-2000 Data Management Unit is not
connected, this adjustment has no effect.
017 DISP LVL IND
Function: Enables/Disables the Main Display to show the
frequency or value while each enabled knob is turned.
Available Values: PTCH (PITCH) / SPED (SPEED) /
CDLY (CW DELAY) / VDLY (VOX DEALAY) / RPWR
(RF POWER) / MICG (MIC GAIN) / PROC (PROCES-
SOR GAIN)
To disable the "function," rotate the ( VFO-B )[ SELECT ]
knob to recall the "function" to be disabled, then press the
[ ENT ] key (one of the [ BAND ] buttons) to change this
setting to "OFF". Repeat the same procedures to enable a
function (setting it to "ON").
018 DISP INDI
Function: Select the indicator location of the current value
when adjusting the following knobs
Available Values: VFD / OEL
Default Setting: VFD
VFD: The current value will show for 3-seconds in the
lower right corner of the Main Display when-
ever the following knob
OEL: The current value will show for 3-seconds in the
SUB DISPLAY-
lowing knob is turned.

: MIC, RF PWR, SPEED, PITCH, DELAY, and
PITCH knob
Page 122
DISPLAY G
.

is turned.

III window whenever the fol-
ROUP
019 DISP SELECT
Function: Selects the display pattern of the SUB DIS-
PLAY- II and SUB DISPLAY- III windows.
Available Values: PTN1 / PTN2 / PTN3
Default Setting: PTN2
PTN1: Generally, the current value is not indicated in
the window, only the graphic is depicted. When
the [ SELECT ] knob is rotated, the current
value will appear under the graphical display.
Three seconds after the turning of the [ SE-
LECT ] knob is stopped, the current value in-
dication disappears.
PTN2: Generally, the current value is indicated with
the small characters and graphical display.
When the [ SELECT ] knob is rotated, the cur-
rent value indication becomes large characters.
Three seconds after the turning of the [ SE-
LECT ] knob is stopped, the current value in-
dication returns to small characters.
PTN3: The current value always indicated with the
large characters and graphical display.
SUB DISPLAY E
XAMPLES
G
ENERAL
PTN1
PTN2
PTN3
DVS G
020 DVS RX LVL
Function: Sets the audio output level from the voice
memory.
Available Values: 0 ~ 100
Default: 50
021 DVS TX LVL
Function: Sets the microphone input level to the voice
memory
Available Values: 0 ~ 100
Default: 50
FT 5000 O
DX
( CONTOUR O )
PERATION
W A
HILE DJUSTING
ROUP
M
PERATING ANUAL