Packet Operation; Packet Setup (Including Subcarrier Frequency); Basic Setup - Yaesu FTDX5000 Series Operating Manual

P O
ACKET
Packet operation is easily accomplished on the FT
transceiver, as in the illustration. "Packet" operation also applies to SSB-based AFSK data modes, such as PSK31, etc.
PACKET
P
ACKET
Before operation can com-
mence, some basic setup proce-
dures must be performed, using
the Menu, to configure your ra-
dio for the desired data mode.
1. Press the [ PKT ] button.
A :
DVICE
 For HF operation, SSB-based data operation is gen-
erally used. One brief press of the [ PKT ] button
will engage packet operation in the "LSB" mode
(by default). Both the "
will appear in the display.
 To operate FM-based 1200-baud packet on the 29/
50 MHz bands, press the [ PKT ] button repeatedly
to illuminate the "
gage the "PKT-FM" mode.
 To engaged Packet operation in the "USB" mode,
repeat pressing the [ PKT ] button until both the
" " and "
2. When the "transmit" command is received from the
TNC, the FT 5000 transmitter will automatically be
DX
engaged. Likewise, the command to return to receive
will cause the radio to revert to the receive mode.
Page 110
PERATION
DX
②
④ ⑤
PACKET JACK
① ③
Pin 3
Pin 4
( I
S
ETUP NCLUDING
M I
ENU TEM
069 DATA DATA IN
070 DATA DT GAIN
071 DATA DT OUT
072 DATA OUT LVL
073 DATA VOX DLY
074 DATA VOX GAIN
B
ASIC
" and " " icons
" and " " icons, to en-
" icons are appear.
5000 by connecting your TNC (Terminal Node Controller) to the
TNC
Pin 1 ( DATA IN ) DATA OUT
Pin 2 ( GND ) GND
( PACKET PTT ) PTT
( DATA OUT ) DATA IN
( BUSY ) (SQL Control)
Pin 5
S
UBCARRIER
A V
VAILABLE ALUES
DATA or PC 083 PKT
0 ~ 100 084 PKT
VFO-A or VFO-B 085 PKT
0 ~ 100 086 PKT
30 ~ 3000 ms 087 PKT
0 ~ 100 088 PKT
S
ETUP
A :
DVICE
 If you need to adjust the output level from the "DATA
OUT" pin of the PACKET jack (pin 4) on the radio,
use Menu item "072 DATA OUT LVL". For the input
level from the TNC, as applied to the DATA IN pin of
the PACKET jack (pin 1), use Menu item "070 DATA
DT GAIN".
 During Packet operation via the rear panel PACKET
jack, the front panel MIC jack is cut off, so you won't
have a "live microphone" problem during data opera-
tion.
N :
OTE
If you anticipate making data transmissions of longer than
a few minutes, we recommend that you use the [ RF PWR ]
knob to reduce the transmitter power to 1/3 ~ 1/2 of its
normal maximum.
Q P :
UICK OINT
PACKET Jack Specifications
 DATA IN (Pin 1)
Input Level: 50 mVp-p
Input Impedance: 10 k-Ohms
 DATA OUT (Pin 4)
Output Level: 100 mVp-p max.
Output Impedance: 10 k-Ohms
FT
DATA
PTT OUT
)
F
REQUENCY
M I A
ENU TEM VAILABLE
LCUT FRQ OFF/100 ~ 1000 Hz
LCUT SLP 18dB/oct or 6dB/oct
HCUT FRQ OFF/700 ~ 4000 Hz
HCUT SLP 18dB/oct or 6dB/oct
PKT DISP –3000 ~ +3000 Hz
PKT SFT –3000 ~ +3000 Hz
5000 O
DX PERATING
DATA
IN
V
ALUES
M
ANUAL