Connecting A Composite Video Source To Port 1; Connecting A S-Video Or Video Source To Port 2 - Barco R9000901 Owner's Manual

Connecting a Composite Video source to port 1.

Composite video signals from a VCR, OFF air signal decoder, etc..
Video input selection :
with the RCU or the build in RCU : press digit button 1
* Note : if using the loop-through Video output, then set the
Termination Switch to the "OFF" position.

Connecting a S-Video or Video source to port 2.

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp 3dB
Pin 4: chrominance signal(C)
300mVpp 3dB
Input selection
with the RCU or the build in RCU : press digit button 2
Depending on the priority setting in the Picture Tuning
menu, Video or S-Video can be displayed.
If the setting is not correct, start up the adjustment mode by
pushing on th ADJUST key.
Select 'Random Access' and press ENTER .
Select 'Selected source' and press ENTER .
Highlight 'Picture Tuning' and press ENTER .
Highlight Port 2 : Video and press ENTER to toggle between VIDEO
or S-VIDEO.
Press EXIT to return.
Press ADJUST to return to operational mode.
* Note: When using the Port 2 loop-through output, set the Termina-
tion Switch in the "OFF" position.
5975007 BARCOGRAPHICS 808S 051196
For video:
Pin 1: earth(ground) video
Pin 2: not connected
3
1
Pin 3: video signal
Pin 4: not connected
2
4
See installation instructions b efore connecting to the supply.
Voir la not ice d'in stallat ion ava nt de r accorder au rés eau.
12 0/2 30 V
7/5 Amp
50/60 Hz
PORT 4/5
Composite
video
TV tuner, e.g. TVDM40 stereo
VCR
See installation instructions before connectin g to the supply.
Voir la no tice d' instal lation avant de rac corder au rés eau.
12 0/2 30 V
7/5 Amp
50/60 Hz
PORT 4/5
Luma/Chroma
VCR S-VHS
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 02
Choose a setup pattern
Select with
from below :
then <ENTER>
<EXIT> to return.
75 Ohm 7 5 Ohm
PORT 2
Audio amplifier
7 5 Ohm 7 5 Ohm
PORT 2
to next projector or
to a monitor
Audio amplifier
or
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 02
RANDOM ACCESS
ADJUSTMENT MODE
Select with or
PICTURE TUNING
then <ENTER>
GEOMETRY
<EXIT> to return.
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
PICTURE TUNING
SOFT EDGE
Select with or
COLOR BALANCE
then <ENTER>
SYNC : FAST
<EXIT> to return.
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with
<ENTER> to accept
<EXIT> to return.
Connections
This device complies with part 15 of
the FCC rules. Operation is subje ct to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this dev ice must
accept any interference received
including inte rference that may cause
undesire d operation"
to next projector or
to a monitor
358
This device complies with part 15 of
the FCC rules. Operation is subje ct to
following two conditions (1). This
device may not cause harmful inter-
ference, and (2) this dev ice must
accept any interference received
including inte rference that may cause
undesire d operation"
359
or
3-3