Replace The Hotend - CraftBot FLOW GENERATION IDEX User Manual

Table of Contents

Advertisement

7.9. Replace the hotend

Assembly instructions:
1.
Items 14 and 15 are placed in block 3 until they stop,
2.
Fasten plate part number 5 to part number 3 with screw number 6.
3.
Slide item number 4 onto item number 3 until it stops.
4.
Wring Nozzle part 1 into block number 3 until it stops.
5.
Screw Heatbreak number 2 onto Nozzle number 1 protruding from block 3 until it stops. (Figure 2)
6.
Tighten Heatsink No. 8 on part number 2 and secure
with screws 7. Make sure that the lower plane of
block 8 coincides with the easing of item number 2
and that the two lows are parallel. (Figure 2)
7.
Assemble the sensor separately: Use screw 11 to
secure item 10 to the FMS sensor 9. (Figure 1)
8.
Tighten spring 13 to screw 12 to then secure item 9 to
part number 8.
9.
In all cases, check under light that no dirt has
entered the assembled parts.
eleket belehelyezzük a 3-mas számú blockba ütközésik,
ítjük az 5-ös számú lemezalkatrészt a 3-mas
ztatjuk a 3-as tételszámú alkatrészre ütközésig.
tekerjük a 3-mas számú blockba ütközésig.
11
tételszámú Nozzle-ra rácsavarjuk a 2-es számú
10
ábra)
e ráhúzzuk a 8-as számú Heatsinket, majd a 7-es
jünk arra, hogy a 8-as block alsó síkja egybeessen a 2-es
és a két lelalpolás párhuzamos legyen. (2 ábra)
rt: A 11-es csavarral rögzítjük a 10-es tételt a 9-es FMS
2-es csavarra, majd ezzel rögzítjük a 9-es tételt a 8-as
sgáljuk meg, hogy szennyeződés nem került az
Figure 1
5
6
1
2. ábra
özésik állítjuk az elemeket!
11
9
Figure 1
14
15
Ütközésik állítjuk az elemeket!
4
ITEM
PART NUMBER
NO.
1
CB4D-PA-124 Nozzle 0.4
2
CBP-PA-101 heatbreak
3
CBP-PA-102 Heatblock
4
CBP-MO-101 Silicone stock
5
CBP-SM-103 Cartridge fixer
6
DIN 912 M2.5 x 6 --- 6N
7
DIN 912 M3 x 6 --- 6N
8
CB4D-PA-123 Extruder heatsink
10
9
14
5
6
1
7
8
2
ITEM
NO.
3
1
CB4D-PA-124 Nozzle 0.4
2
CBP-PA-101 heatbreak
3
CBP-PA-102 Heatblock
4
CBP-MO-101 Silicone stock
5
CBP-SM-103 Cartridge fixer
6
DIN 912 M2.5 x 6 --- 6N
7
DIN 912 M3 x 6 --- 6N
8
CB4D-PA-123 Extruder heatsink
9
CB4D-PCB-004 PAT FMS
10
F623zz
11
DIN EN ISO 7046-1 - M2.5 x 10 - Z - 10N
Name
12
DIN 912 M3 x 12 --- 12N
Nozzle 0.4
13
AC450-4200-6.000-MW-10.000-C-N-MM
Heatbreak
14
24V40W Heater Cartridge 105mm cable
Heatblock
15
PT 100 Temperature sensor 105mm length
Silicone sock
Designed by:
Cartridge fixer
Skorka Olivér
Drawn by:
Screw
Bartók Viktória
Approved by:
Screw
Nagy Gergely
Date of approval:
Extruder heatsink
IDEX USER MANUAL
Figure 2
13
15
12
11
8
2
9
3
10
4
PART NUMBER
Extruder heatsink
QTY.
1
Compression Spring
1
24V40W Heater Cartridge 105mm cable
1
Temperature sensor 105 mm length
1
Title:
1
1
Material:
Heat Treatment:
-
2
Surface Treatment:
Colour:
1
-
Do not push the heatbreak
against the heatsink!
13
12
11
9
10
7
Name
QTY.
Nozzle 0.4
1
Heatbreak
1
Heatblock
1
Silicone sock
1
Cartridge fixer
1
Screw
1
Screw
2
1
PAT FMS
1
Bearing
1
Screw
1
Screw
1
1
1
1
Drawing Number:
Revision:
2.
CB4D-AS-118
40
Weight:
Page No.:
1/1
74.21 g
Scale:
Sheet Size:
M1:2
A2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FLOW GENERATION IDEX and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents