Table of Contents
Advertisement
ASSEMBLY INSTRUCTIONS
Hydraulic Installation
NOTES
See Figures 3-10
through
fittings (factory installed and those installed during
setup.)
Refer to Figures
3-10
and
diagrams for 9650-38' and 9650-42' models.
Refer to Figures
3-16
and
diagrams for 9650-46' and 9650-50' models.
Refer to Figure
3-9
for hydraulic cylinder installation
models 38' 9650FH 38'/42'.
1. Attach the base end of each 4-1/2 x 30 hydraulic
cylinder to the fold cylinder mount on the center
frame with clevis and roll pins provided with each
cylinder as shown in 3-9. Position the cylinders so
the hydraulic ports point to rear on front cylinders and
to front on the rear cylinders.
NOTE
Rod ends of fold cylinders need to be left
unassembled until fold hydraulic system is fully
charged with oil to prevent machine damage.
2. Using 1-1/4 x 6-1/8 fold pin, 1-1/4N flat washers, and
5/16 x 2-1/2 spring slotted pins, attach the rod end of
the 4-1/2 x 30 cylinders to the slotted mounts on the
inner wing frames
See Figure 3-9
3. Using a 1-1/4-7 x 7 hex head cap screw, flat washers,
wing extension roller, and hex lock nut, attach the rod
end of the 4 x 16 hydraulic cylinders to the fold links
on the double hinge
over-tighten screws. Fold links should pivot freely
without binding or dragging. Tighten screws to
remove excess slack, but still allow fold links to flex,
and rotate bolt by hand.
Restrictors are installed in the rod end of wing
fold cylinders to prevent uncontrolled dropping
of wings. Removal of these restrictors, or
improper installation can result in serious
damage to the implement.
3-19
for proper restrictor fitting identification and
location.
3-14
3-21
for hydraulic cylinder
3-15
for lift and fold hydraulic
3-21
for lift and fold hydraulic
See Figure 3-9
Do not
CAUTION
See Figures 3-13
4. Install 90 degree regular adapter fittings in both ends
of all lift cylinders (4 x 10, 3-3/4 x 10, and 3-1/2 x 10)
See Figures 3-10
downward, rod fittings point upward.
5. Attach the 8 port manifold assembly to the front
manifold bracket on the implement using 1/2-13 x
3-1/2 hex head cap screws and hex lock nuts.
6. Attach hose clamps to the hitch using 3/8-16 x 2-1/2
hex head cap screws and hex lock nuts.
7. Install a 6-1/4" long piece of black trim in the top hole
of the lift bearing caps. Outer wing bearing caps do
not require trim. Route rear fold and lift hydraulic
hoses through bearing caps between frame sections
See Figure
8. Install lift system hoses per Figure
and 9650-42) or Figure
9650-50.) Wrap lift system hoses with blue hose
wrap.
9. Install fold system hoses per Figure
and 9650-42) or Figure
9650-50.) Wrap fold system hoses with yellow hose
wrap.
10. Attach hose clamps to the center and wing frames
See Figures 3-8
screws and 3/4 lock nuts.
and
Figure 3-8: Hose Clamp Installation
and 3-16. Base fittings point
3-7.
6-1/4" LONG BLACK TRIM
LIFT BEARING CAP
Figure 3-7: Trim Installation
3-16
(9650-46 and
3-19
(9650-46 and
using 3/8 x 2-3/4 hex head cap
3/8 X 2-3/4 BOLT,
3/8 LOCK NUT
3-10
(9650-38
3-14
(9650-38
F-1090-1120
Advertisement
Table of Contents
