Introduction and Safety Information Introduction The Landoll Model 9630FH Field Cultivator is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.
5. Use a locking-style hitch pin that properly fits the The safety statements contained in this manual relate to tractor drawbar and the implement hitch. Lock the the operation of the Model 9630FH Field Cultivator. tractor drawbar in the center position to prevent loss of steering control.
INTRODUCTION AND SAFETY INFORMATION High Pressure Fluid Safety 6. Attach the safety chain to the tractor recommended drawbar support. Provide only enough slack in the 1. Escaping fluid under pressure can be nearly invisible chain for turning. Do not attach the safety chain to an and have enough force to penetrate the skin causing intermediate support.
INTRODUCTION AND SAFETY INFORMATION Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.
Chapter 2 Standard Specifications Model Specifications 9630FH Field Cultivator Model Number 9630FH-30 9630FH-32 9630FH-34 Working Width 30'-6” 32'-6” 34'-6” Transport Width 17’-2” 17’-2” 17’-2” Transport Height 13’-5” 14’-0” 14’-11” Number of Shanks Shanks per Section 17-27-17 19-27-19 21-27-21 3” Center Frame, 2-1/4”...
STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
Chapter 3 Assembly Instructions It is very important that your new 9630FH Field Cultivator WARNING be properly assembled, adjusted and lubricated before use. Illustrations in this section show proper assembly Do not attempt to lift heavy parts (such as the procedures.
ASSEMBLY INSTRUCTIONS Center Frame Assembly- 9630FH 9. Attach the bottom end of the cylinder lift arms to the outside of bearing housing mounts with 1 x 2-3/4 bolts and 1 locknuts. IMPORTANT 10. Connect the top end of the cylinder lift arms to the Read all safety precautions at the front of the section radius rod with 1 x 3-1/2 bolts and locknuts.
Page 47
ASSEMBLY INSTRUCTIONS HOSE CLAMP, CENTER FRAME 3/8 X 2-3/4 BOLT, RADIUS ROD ASSEMBLY RH 3/8 LOCK NUT ASSEMBLY DETAIL A MANIFOLD 8 PORT, CENTER FRAME 1/2 X 3-1/2 BOLT, ASSEMBLY LH 1/2 LOCK NUT 54” 1 X 3-1/2 BOLT, STAND 1 LOCK NUT 1-1/4 X 2-3/4 SHANK...
ASSEMBLY INSTRUCTIONS Center Frame Fold and Depth 3. Insert a slide pad into the bottom of the hole in the valve mount. Control Assembly 4. Install a 90 deg elbow in the back side (opposite the button) of the depth control valve. Fasten the valve IMPORTANT and fitting to the valve mount using 5/16x2-1/4 bolts and lock nuts.
Page 49
ASSEMBLY INSTRUCTIONS WING STABILIZER REAR FOLD ASSEMBLY 9650FH-46’-50’, CYLINDER MOUNT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 LOCK NUT 5/8 LOCK NUT DEPTH STOP TUBE ASSEMBLY, 5/8 X 2-1/2 BOLT, 5/8 LOCK NUT DETAIL A FRONT DEPTH CONTROL FRONT FOLD...
ASSEMBLY INSTRUCTIONS Gauge Wheel Assembly Center 1. Remove the shipping u-bolts and nuts from front of the gauge wheel extension mounts See Figure 3-3. 2. Attach the gauge wheel assemblies to the front of the IMPORTANT center frame with 3/4 x 5-1/2 bolts and 5/8 lock nuts. Read all safety precautions at the front of the section 3.
Page 51
ASSEMBLY INSTRUCTIONS RADIUS ROD ASSEMBLY 3/4 X 5-1/2 BOLTS & LOCK NUTS 1 X 7-1/2 BOLTS 21” & LOCK NUTS GAUGE WHEEL ASSEMBLIES GAUGE WHEEL EXTENSION MOUNT SHIPPING U-BOLTS & 5/8 NUTS 1 X 7-1/2 BOLTS & LOCK NUTS 6-BOLT TIRE/WHEEL ASSEMBLIES Figure 3-3: Gauge Wheel Assembly Center...
ASSEMBLY INSTRUCTIONS Hitch Assembly 3. Insert a 3/4-10 x 7 hex bolt into the hose holder tube on the hitch from the bottom side so the threads point upward. Hold in place with a 3/4-10 flange nut with IMPORTANT the flange pointing upward as well. Do not tighten this Read all safety precautions at the front of the section cap screw, so the hose holder bracket may pivot before attempting any of the following procedures.
Page 53
ASSEMBLY INSTRUCTIONS WING NUT HOSE HOLDER CLAMP 1/4-20 X 1 HEX BOLT 3/8-16 X 2 HOSE HOLDER BRACKET HEX NUT 3/4-10 FLANGE NUT STOR-A-WAY HARNESS 3/4-10 X 7 3/8-16 X 3-1/2 HEX BOLT ALL THREAD 1/4-20 LOCK NUT DETAIL A DETAIL A 1-7/16 X 7-1/4 HITCH PIN,...
ASSEMBLY INSTRUCTIONS Wing Frame Assembly Wing Gauge Wheel Installation 1. Attach wing frames to center frame using 1-1/4 1. Remove the shipping u-bolts and nuts from front of flange bearings, flat washers, 1-1/4 x 6-1/8 pin and the gauge wheel extension mounts See Figure 3-5.
Page 55
ASSEMBLY INSTRUCTIONS 1-1/4 X 6-1/8 PINS, FLAT WASHERS 5/16 X 2-1/2 SPRING SLOTTED PINS SHANK ASSEMBLY 1 X 7-1/2 BOLTS RADIUS ROD 21” & LOCKNUTS ASSEMBLY 3/4 X 5-1/2 BOLTS STAND & LOCKNUTS GAUGE WHEEL GAUGE WHEEL ASSEMBLIES EXTENSION MOUNT SHANK ASSEMBLY SHIPPING U-BOLTS...
ASSEMBLY INSTRUCTIONS Hydraulic Installation 4. Install a 6-1/4” long piece of black trim in the top hole of the lift bearing caps. Outer wing bearing caps do not require trim. Route rear fold and lift hydraulic NOTES hoses through bearing caps between frame sections See Figures 3-9 3-12 for hydraulic cylinder fittings...
Page 57
HOSE 3-3/4 X 10 3/4-16 MALE CYLINDER COUPLER 90° #8 BLUE HOSE WRAP ADAPTER FRONT OF 16 PORT MACHINE MANIFOLD 16 PORT #8 TO #8 LIFT/FOLD ADAPTER MANIFOLD ASSEMBLY DETAIL A 3/4-16 PLUG Figure 3-9: Hydraulic Lift Installation 9630FH 3-13...
Page 58
NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-10: Hydraulic Lift Layout 9630FH LH 3-14 F-1105-1120...
Page 59
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-11: Hydraulic Lift Layout 9630FH RH 3-15...
Page 60
90° #8 ADAPTER 16 PORT MANIFOLD #8 TO #8 #8 TO #8 16 PORT ADAPTER ADAPTER LIFT/FOLD MANIFOLD ASSEMBLY 8 PORT FOLD MANIFOLD 8 PORT 3/4-16 PLUG ASSEMBLY MANIFOLD DETAIL B DETAIL A Figure 3-12: Hydraulic Fold Installation 9630FH 3-16 F-1105-1120...
Page 61
ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-13: Hydraulic Fold Layout 9630FH 3-17...
Page 62
ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-18 F-1105-1120...
Page 63
ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART 2-PIN 3-PIN 6-PIN...
See Figures 3-15 Detail A. and lock nuts. 10. install the Landoll decal to the rear of the cylinder 5. Attach the ag red single LED lamps and reflector mount rear. assembly to tail light mounts using 1/4 x 1-1/2 bolts 11.
Page 65
SIS 20 MPH DECAL, FRONT BOLTS SMV EMBLEM & LOCK NUT 1/4 X 1 BOLTS, RED AG LOCK NUTS LAMP REFLECTOR ASSEMBLY, INCLUDES MOUNT, LANDOLL RED & ORANGE REFLECTOR DECAL TAIL LIGHT DETAIL A LED AMBER MOUNT CYLINDER LIGHT MOUNT ASSEMBLY RH...
Page 66
ASSEMBLY INSTRUCTIONS NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE CLAMPS ALONG HYDRAULIC HOSES NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE LOOPS ALONG HYDRAULIC NOTE: SECURE HOSES LIGHT HARNESSES WITH TIES STRAPS AS NEDDED TO KEEP CLEAR OF ANY MOVING PARTS NOTE: RUN LIGHT HARNESS THROUGH HOSE...
Page 67
ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-23...
ASSEMBLY INSTRUCTIONS Shank Installation NOTE See Figure 2-2 through for shank placement Spring shank assemblies with frame extensions (front dimensions. Verify that all shank clamps and extensions bar) are mounted reversed for narrower shipment. These are properly installed. shanks must be removed and turned forward for proper 1.
Page 69
ASSEMBLY INSTRUCTIONS SPRING SHANK ASSEMBLY 5/8 X 4-11/16 X 5-1/2 U-BOLT, 5/8 FLANGE LOCK NUT 1/2 X 3-1/4 BOLT, 1/2 LOCK NUT 5/8 X 4-11/16 X 4-3/4 U-BOLT, 5/8 FLANGE LOCK NUT 5/8 X 1-3/4 ROUND SPRING SHANK SHANK HEAD SQUARE NECK EXTENSION BOLT, 5/8 FLANGE LOCK NUT...
ASSEMBLY INSTRUCTIONS 4 Row Coil Tine Harrow 2. Assemble the coil tine assemblies to the harrow arms. Installation 3. Front row tines are assembled with the tines above Refer to See Figures 2-7 through 2-18 for 4 row coil tine the stop bolts to prevent damage when shipping harrow placement.
Page 71
ASSEMBLY INSTRUCTIONS ANGLE ADJUSTMENT HARROW ADJUSTMENT PIN PLATE GANG BAR MORE LESS PLATE AGGRRESIVE AGGRRESIVE 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (INSTALL BOLT IN INNER BOTTOM HOLE) NOTE: REMVOVE STOP BOLTS AND ROTATE DOWN WITH STOP BOLTS ABOVE TINES 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (INSTALL BOLT IN INNER TOP HOLE)
ASSEMBLY INSTRUCTIONS 3 Row Coil Tine and Reel Harrow 2. Attach the harrow tine assemblies in correct location with 5/8 u-bolts and 5/8 flange lock nuts. Installation 3. Attach reel assemblies to the reel arm assemblies See Figures 2-19 through 2-30 for 3 Row Coil Tine using 5/8 x 3-11/16 x 4-5/8 u-bolts and 5/8 lock nuts.
ASSEMBLY INSTRUCTIONS 5 Row Spike Harrow Installation 4. Attach spike bars to 5 row spike harrow arm assemblies per placement drawings using bar clamp See Figures 2-15 through 2-20 for 5 Row Spike Harrow plates, spike bar clamp plates, harrow bar mounts, placement dimensions.
Page 75
ASSEMBLY INSTRUCTIONS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 5 ROW SPIKE HARROW ARM 3/4-10 X 9 HEX BOLT, 3/4 LOCK NUT, HARROW ARM CLAMP PLATE, 3/4-10 X 5 HEX BOLT, 3/4 LOCK NUT 1/2-13 X 3 HEX BOLT, LYNCH PIN 1/2 FLANGE LOCK NUT PULL CHAIN BRACKET...
ASSEMBLY INSTRUCTIONS 3 Row Spike and Reel Harrow 7. Attach flat bar reels with angled blades as shown See Figure 3-22. Installation See Figures 2-43 2-54 for 3 Row Spike and Reel Harrow or See Figures 2-55 2-66 3RSD & flat reel for placement dimensions in “Standard Specification”...
Page 77
ASSEMBLY INSTRUCTIONS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3 RSD ARM ASSEMBLY 3 RSD ARM W/O SPRING ASSEMBLY 3 RSD ARM W/SPRING ASSEMBLY W/SPRING 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT 3/4 X 5-1/2 BOLT, 3/4 LOCK NUT HARROW BAR MOUNT W/TABS...
ASSEMBLY INSTRUCTIONS Rear Tow Hitch (Option) 7. Attach the front of the tow hitch assembly to the cultivator frame cross tubes using 5/8-11 x 3-11/16 x 1. Unfold and lower the field cultivator to the ground. 5-1/2 u-bolts and 5/8-11 lock nut. 2.
Page 79
ASSEMBLY INSTRUCTIONS NOTE: ROUTE HOSES HOSE CLAMP NOTE: WEIGHT HITCH ALONG OTHER HOSES, PLATE BOLTS TO TOP TRUOUGH HOSE CLAMPS, OF WEIGHT PLATES 3/8-16 X 2-3/4 ALONG CENTER FRAME, ON HITCH, USE HEX BOLT & AND HITCH TO FRONT EXISTING NUTS 3/8-16 LOCK OF MACHINE &...
Page 80
ASSEMBLY INSTRUCTIONS 26” 26” NOTE: CENTER REAR TOW HITCH RIGHT REAR TANDEM LIGHT ON CENTER FRAME TAIL LIGHT MOUNT HARNESS MAIN WIRING HARNESS LIGHTING MODULE NOTE: ROUTING OF TANDEM LIGHT HARNESS REAR TOW HITCH ASSEMBLY NOTE: ROUTING OF HYDRAULIC HYDRAULIC HOSES HOSES TANDEM LIGHT HARNESS...
DANGER DANGER Never allow anyone to ride on the 9630FH Field When transporting the unit, place cylinder Cultivator at any time. Allowing a person to ride lockouts in the transport lock position after fully on the machine can inflict serious personal injury extending the cylinders.
OPERATION AND MAINTENANCE Hydraulic Lift System 1. The rephasing hydraulic lift system contains smaller wing frame cylinders plumbed in series with larger The Field Cultivator is equipped with a rephasing center frame cylinders. It is important that the hydraulic lift system to raise and lower the unit in the field. cylinders be connected in the proper series for the lift system to operate correctly.
Page 83
OPERATION AND MAINTENANCE Table provided for general use. NOTES:...
OPERATION AND MAINTENANCE Hydraulic Fold System 5. The hydraulic fold system is equipped with restrictors in the cylinders to prevent uncontrolled falling of wing The Field Cultivator is equipped with a hydraulic fold frames when folding/unfolding. Removal or improper system to raise and lower the wing frames for narrow assembly of these restrictors can cause the machine transport.
Page 85
OPERATION AND MAINTENANCE NOTE: BOTH SIDES ARE EITHER FOLDED OR UNFOLDED DEPENDENT ON OPERATION DETAIL A DETAIL B WING STABILIZER BRACKET MOUNT WING STABILIZER BRACKET MOUNT DETAIL B TRANSPORT LOCK PIN STORAGE LOCATION WHEN FOLDED DETAIL A TRANSPORT LOCK PIN STORAGE LOCATION WHEN UNFOLDED Figure 4-4: Wing Stabilizer Bracket Locks...
OPERATION AND MAINTENANCE Transporting 3. When towing in combination, the maximum equipment ground speed shall be limited to the 1. Check and follow all federal, state, and local lowest specified ground speed of any of the towed requirements before transporting the Field Cultivator. implements.
OPERATION AND MAINTENANCE Tractor Preparation Leveling (Side to Side) The Landoll 9630FH Field Cultivator is designed to be 1. Leveling the Field Cultivator side-to-side involves pulled by tractor equipped with a double lip or clevis type leveling the center frame then leveling the wing hitch.
Page 88
RADIUS TUBE Figure 4-6: Leveling from Side to Side 9630FH Gauge Wheels Measure the distance from the top of the wing frame to the top of the walking beam spindle. Lay a 1. The front gauge wheels of the floating hitch cultivator...
Page 89
OPERATION AND MAINTENANCE RH & LH LOCKING NUTS 1/2” LOCKING SET SCREW 21” MEASURE RADIUS ROD 1-1/2” LESS TUBE WALKING BEAM GAUGE WHEEL SPINDLE (TOP) SPINDLE (TOP) Figure 4-7: Gauge Wheel Adjustment To adjust the gauge wheel radius rod, loosen both the right and left-hand threaded locking nuts.
OPERATION AND MAINTENANCE Depth Stop Adjustment LED Light Operation 1. The operating depth of the Field Cultivator is 1. Attach the seven-pin plug to the socket at the rear of controlled by a single-point depth stop. The stop is the tractor. The socket must be in good working located at the center front of the machine order, and free of dirt, grease, and corrosion.
OPERATION AND MAINTENANCE Spring Shank 5/8 X 3 BOLT 1. The Field Cultivator may be equipped with spring 1/8” shanks. The spring shanks feature a 185 lb. point SPRING PLATE load and a 10” trip height to clear field obstructions. Shanks are 5/8 x 1-3/4 heat treated steel.
OPERATION AND MAINTENANCE Wheel Bearing Maintenance – Wheel Bearing Maintenance -- Non Triple-Lip Triple-Lip Wheel bearing maintenance should be performed at the Transport tires use a self-contained seal with multiple beginning of every season of use. Check the wheel lips. The seal fits tight on both the spindle and wheel hub. bearings periodically for excessive end play.
OPERATION AND MAINTENANCE Lubrication 3. Wheel seals, when properly installed, will allow grease to pass without harm to seals. Regular 1. A proper maintenance schedule will insure a long lubrication will extend service life, particularly in operating life and peak performance. Performing the severe operating conditions.
Page 94
OPERATION AND MAINTENANCE Figure 4-12: Lubrication Points LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Gauge Wheel Radius Rod 1 each Gauge Wheel Hubs 1 each Gauge Wheel Weldment Hubs 1 each Walking Beam 1 each Lift Hubs 1 each Lift Radius Rod...
Page 95
OPERATION AND MAINTENANCE Table provided for general use. NOTES: 4-15...
OPERATION AND MAINTENANCE 4 Row Coil Tine Harrow 2. In general tine harrows have better capabilities for handling more residue and wetter conditions. When Adjustments operating the coil tine harrow, a more vertical tine tooth angle will make the harrow more aggressive. A 1.
Page 97
OPERATION AND MAINTENANCE 1-8 HEX NUTS ANGLE ADJUSTMENT PLATE SPRING HARROW ADJUSTMENT PIN ASSEMBLY MORE LESS AGGRRESIVE AGGRRESIVE 1-1/32” 22” 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (PLACE BOLT IN INNER BOTTOM HOLE) 1/2 X 1-1/4 RD HEAD SQ GANG BAR NECK SCREW (PLACE BOLT IN INNER PLATE...
OPERATION AND MAINTENANCE 3 Row Coil Tine and Reel 4. Each coil tine harrow may be adjusted for spring pressure as well See Figure 4-14. Raise the tine Adjustments harrow off the ground. Remove the clevis pin from the spring tube and install in a heavy or light setting 1.
Page 99
OPERATION AND MAINTENANCE SPRING ASSEMBLY MORE LESS 1-8 HEX NUTS AGGRRESIVE AGGRRESIVE 1/2” 21-3/4” REEL ASSEMBLY HEAVY CLEVIS PIN LIGHT HARROW ADJUSTMENT PIN CLEVIS PIN HARROW ADJUSTMENT PIN REEL 3 ROW COIL TINE ASSEMBLY ASSEMBLY HARROW ADJUSTMENT HOLES Figure 4-14: 3 Row Coil Tine and Reel Adjustments 4-19...
OPERATION AND MAINTENANCE 5 Row Spike Harrow 2. For the most aggressive spike to action, install the harrow adjustment pin in the forward mounting hole Adjustments over each bar clamp for each spike bar Figure 4-15. This will position the spike teeth to be in 1.
Page 101
OPERATION AND MAINTENANCE LEAST MIDDLE MOST CARRYING CHAIN TOOTH ANGLE TOOTH ANGLE TOOTH ANGLE CLEVIS PIN FORWARD PULL CHAIN SPIKE BAR ASSEMBLY BAR CLAMP W/TABS CLEVIS PIN BAR CLAMP Figure 4-15: 5 Row Spike Harrow Adjustments 4-21...
OPERATION AND MAINTENANCE 3 Row Spike and Reel 5. The 12” diameter reel consists of nine 3/4” diameter round bars with a chevron shape for smoother Adjustments rotation. The reels have no inner shaft to reduce plugging in wetter conditions. The reels operate 1.
Page 103
OPERATION AND MAINTENANCE LEAST TOOTH ANGLE MIDDLE TOOTH ANGLE SPRING SPRING CARRYING CHAIN MOST TOOTH ANGLE ASSEMBLY ASSEMBLY 1-8 HEX NUTS 21-3/4” REEL ASSEMBLY FORWARD PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP BAR CLAMP W/TABS FLAT REEL ASSEMBLY SPIKE BAR ASSEMBLY CLEVIS PIN REEL...
OPERATION AND MAINTENANCE Storage 1. The service life of the Field Cultivator will be extended by proper off-season storage practices. Prior to storing the unit, complete the following procedures: a. Completely clean the unit. b. Inspect the machine for worn or defective parts. Replace as needed.
Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 9630FH Field Cultivator. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM...
Page 106
TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION SWEEPS NOT CUTTING, LEAVING Shanks not positioned correctly Check for proper shank placement SKIPS Sweeps not wide enough Use wider sweeps Sweeps set too shallow Increase operating depth Incorrect sweep angle Use 47 degree sweeps Incorrect shank spring adjustment Adjust spring shank.
Page 107
Document Control Revision Log: Date Form # Improvement(s): Description and Comments 11/20/2020 F-1105 New Manual 12/17/2020 F-1105-1220 Initial Release...
Page 108
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 9630FH Field Cultivator Operator’s Manual Re-Order Part Number F-1105-1220 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...