1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. 9650FH
  6. Operator's manual

Landoll 9650FH Operator's Manual

Field cultivator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model 9650FH
Field Cultivator
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-1090-1120
11/2020-Present

Advertisement

Table of Contents
loading

Related Manuals for Landoll 9650FH

Summary of Contents for Landoll 9650FH

  • Page 1 Model 9650FH Field Cultivator Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1090-1120 11/2020-Present...
  • Page 2 Manuals for the 9650FH FC MANUAL NUMBER MANUAL NAME F-1090 9650FH FC Operator’s Manual F-1091 9650FH FC Parts Manual...

  • Page 3: Table Of Contents

    Assembly Instructions Center Frame Assembly- 9650FH-38’, 42’, 46’ & 50’ ......3-2 Center Frame Fold and Depth Control Assembly .
  • Page 4 Wheel Bearing Maintenance ..........4-12 Lubrication .

  • Page 5: Introduction And Safety Information

    Introduction and Safety Information Introduction The Landoll Model 9650FH Field Cultivator is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.

  • Page 6: Understanding Safety Statements

    Never tow the implement with a motor (decals) before you attempt to operate or maintain vehicle. Tow the implement only with a properly this vehicle. ballasted tractor. The safety statements contained in this manual relate to the operation of the Model 9650FH Field Cultivator. F-1090-1120...

  • Page 7: Attaching, Detaching, And Storage

    INTRODUCTION AND SAFETY INFORMATION 5. Use a locking-style hitch pin that properly fits the 4. Block the implement so it will not roll when working tractor drawbar and the implement hitch. Lock the on or under it to prevent injury. tractor drawbar in the center position to prevent loss 5.

  • Page 8: Tire Safety

    INTRODUCTION AND SAFETY INFORMATION Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.

  • Page 9: Standard Specifications

    Chapter 2 Standard Specifications Model Specifications 9650FH Field Cultivator Model Number 9650.-38 9650-42 9650-46 9650-50 Working Width 38'-6” 42'-6” 44'-6” 50'-6” Transport Width 17'-11” 17'-4” 17'-4” 17'-4” Transport Height 12'-3” 12'-3” 13'-11” 13'-11” Number of Shanks Shanks per Section 10-15-27-15-10...

  • Page 10: General Torque Specifications (Rev. 4/97)

    STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).

  • Page 11: Hydraulic Fitting Torque Specifications

    STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
  • Page 12 14” 20” 8” 20” 2” 2” 42’ 14” 38’ 2” 2” 2” 8” 7-7/8” 14” 8” 8” 14” 8” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION NOTE: LOCATION OF 172714, 3” SHANK EXTENSION Figure 2-1: Shank Placement 9650FH-38’-42’ LH F-1090-1120...
  • Page 13 13-1/2” 13-1/2” 2” 2” 8” 8” 14” 2-1/2” 2” 14” 2” 8” 8” 20” 20” 20” 2” 2” 2” 2” 8-1/2” 8” 8” 14” 14” 8” 14” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION Figure 2-2: Shank Placement 9650FH-38’-42’ CENTER...
  • Page 14 14” 20” 20” 8” 2” 2” 42’ 14” 38’ 2” 2” 2” 8” 14” 8” 8” 14” 7-7/8” 8” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION NOTE: LOCATION OF 172714, 3” SHANK EXTENSION Figure 2-3: Shank Placement 9650FH-38-42’ RH F-1090-1120...
  • Page 15 STANDARD SPECIFICATIONS Table provided for general use. NOTES:...
  • Page 16 2” 2” 50’ 14” 46’ 2” 2” 2” 2” 26” 8” 8” 14” 8” 8” 8” 14” 14” 8” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION NOTE: LOCATION OF 172714, 3” SHANK EXTENSION Figure 2-4: Shank Placement 9650FH-46’-50’ LH F-1090-1120...
  • Page 17 14” 14” 2” 2” 8” 8” 2” 14” 14” 2-1/2” 2” 8” 8” 20” 20” 20” 2” 2” 2” 2” 8-1/2” 8” 8” 14” 14” 8” 8” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION Figure 2-5: Shank Placement 9650FH-46’-50’ CENTER...
  • Page 18 2” 50’ 14” 46’ 2” 2” 2” 26” 2” 8” 14” 14” 8” 8” 8” 14” 8” 8” NOTE: LOCATION OF 194616, 1/2” SHANK EXTENSION NOTE: LOCATION OF 172714, 3” SHANK EXTENSION Figure 2-6: Shank Placement 9650FH-46’-50’ RH 2-10 F-1090-1120...
  • Page 19 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-11...
  • Page 20 STANDARD SPECIFICATIONS 13” 3-1/4” 18” 4” 5-1/4” 14-13/16” 2-1/4” 9-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 8 INCH 6 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-7: 4 Row CT Harrow Placement 9650-38’FH LH 2-12 F-1090-1120...
  • Page 21 STANDARD SPECIFICATIONS 20” 20” 4-1/4” 7-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 9 TINE 8 INCH HARROW ASSEMBLY Figure 2-8: 4 Row CT Harrow Placement 9650-38’FH CENTER 2-13...
  • Page 22 STANDARD SPECIFICATIONS 4” 16” 3-1/4” 13” 3-7/16” 11-5/8” 8-7/16” 6-1/4” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 8 INCH 5 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-9: 4 Row CT Harrow Placement 9650-38’FH RH 2-14 F-1090-1120...
  • Page 23 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-15...
  • Page 24 STANDARD SPECIFICATIONS 5” 3-1/4” 13” 8” 9-1/4” 6-13/16” 5-1/4” 5-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 8 INCH 6 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-10: 4 Row CT Harrow Placement 9650-42’FH LH 2-16 F-1090-1120...
  • Page 25 STANDARD SPECIFICATIONS 13” 13” 5-1/4” 8-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 8 INCH HARROW ASSEMBLY Figure 2-11: 4 Row CT Harrow Placement 9650-42’FH CENTER 2-17...
  • Page 26 STANDARD SPECIFICATIONS 8” 13” 3-1/4” 5” 2-1/4” 8-7/16” 3-5/8” 12-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 8 INCH 6TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-12: 4 Row CT Harrow Placement 9650-42’FH RH 2-18 F-1090-1120...
  • Page 27 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-19...
  • Page 28 STANDARD SPECIFICATIONS 19” 5” 20” 8” 10-7/16” 4-1/4” 3-1/4” 5-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 8 INCH 7 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-13: 4 Row CT Harrow Placement 9650-46’FH LH 2-20 F-1090-1120...
  • Page 29 STANDARD SPECIFICATIONS 13” 13” 5-1/4” 8-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 8 INCH HARROW ASSEMBLY Figure 2-14: 4 Row CT Harrow Placement 9650-46’FH CENTER 2-21...
  • Page 30 STANDARD SPECIFICATIONS 8” 20” 5” 19” 2-1/4” 7-7/16” 7-1/4” 6-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 8 INCH 6 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-15: 4 Row CT Harrow Placement 9650-46’ FH RH 2-22 F-1090-1120...
  • Page 31 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-23...
  • Page 32 STANDARD SPECIFICATIONS 5” 5” 20” 8” 9-1/4” 10-7/16” 4-1/4” 5-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 8 TINE 8 INCH 7 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-16: 4 Row CT Harrow Placement 9650-50FH LH 2-24 F-1090-1120...
  • Page 33 STANDARD SPECIFICATIONS 8” 13” 13” 8” 5-7/16” 5-1/4” 8-7/16” 2-1/4” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 8 INCH HARROW ASSEMBLY Figure 2-17: 4 Row CT Harrow Placement 9650-50’FH CENTER 2-25...
  • Page 34 STANDARD SPECIFICATIONS 8” 20” 5” 5” 2-1/4” 7-7/16” 7-1/4” 12-7/16” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 8 INCH 8 TINE 8 INCH HARROW ASSEMBLY HARROW ASSEMBLY Figure 2-18: 4 Row CT Harrow Placement 9650-50’FH RH 2-26 F-1090-1120...
  • Page 35 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-27...
  • Page 36 STANDARD SPECIFICATIONS 12-7/8” 12-3/4” 3-1/4” 3-1/2” 6-5/8” 6-3/4” 5” 4-1/4” 19-5/8” 23-3/8” 13-7/8” 10-1/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 4 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 60” REEL ASSEMBLY 90”...
  • Page 37 STANDARD SPECIFICATIONS 3-1/4” 8-1/4” 8-1/4” 3-1/4” 7-1/2” 5” 4” 5-1/8” 11-3/4” 13-1/2” 13-5/8” 11-5/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 75”...
  • Page 38 STANDARD SPECIFICATIONS 3-1/2” 3-1/4” 12-3/4” 12-7/8” 4-3/8” 5-1/8” 6-5/8” 6-3/4” 10-1/4” 13-3/4” 23-1/2” 19-1/2” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 4 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 60”...
  • Page 39 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-31...
  • Page 40 STANDARD SPECIFICATIONS 3-1/4” 3-1/4” 19” 19” 13-1/4” 13” 4-3/4” 6-7/8” 32-1/2” 21-3/8” 22-1/8” 18-1/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 5 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 75”...
  • Page 41 STANDARD SPECIFICATIONS 3-1/4” 8-1/4” 8-1/4” 3-1/4” 7-1/2” 5” 4” 5-1/8” 19-1/4” 6” 21” 19-1/4” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90”...
  • Page 42 STANDARD SPECIFICATIONS 19” 19” 3-1/4” 3-1/4” 13-1/8” 4-7/8” 13-1/8” 6-3/4” 18-1/8” 22-1/8” 21-3/8” 32-1/2” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90”...
  • Page 43 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-35...
  • Page 44 STANDARD SPECIFICATIONS 3-1/4” 6” 19” 9” 6-5/8” 9-7/8” 4-3/4” 4-7/8” 7” 19-1/2” 20-5/8” 15-5/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 105”...
  • Page 45 STANDARD SPECIFICATIONS 13” 8-1/4” 8-1/4” 13” 6-3/4” 6-7/8” 21-1/2” 13-1/2” 13-1/2” 21-5/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 3 ROW HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-26: 3 Row Tine & Reel Placement 9650-46’FH CENTER 2-37...
  • Page 46 STANDARD SPECIFICATIONS 9” 19” 6” 3-1/4” 4-7/8” 4-3/4” 9-3/4” 6-1/2” 15-5/8” 20-5/8” 19-1/2” 7” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 90”...
  • Page 47 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-39...
  • Page 48 STANDARD SPECIFICATIONS 3-1/4” 9” 13” 19” 13” 4-7/8” 6-3/4” 6-7/8” 29-1/2” 15” 22-1/8” 18-1/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105”...
  • Page 49 STANDARD SPECIFICATIONS 3-1/4” 8-1/4” 8-1/4” 3-1/4” 5” 4” 7-1/2” 5-1/8” 19-1/4” 6” 21” 19-1/4” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90”...
  • Page 50 STANDARD SPECIFICATIONS 19” 13” 9” 3-1/4” 6-3/4” 6-7/8” 4-3/4” 13-1/8” 18-1/8” 22-1/8” 15” 29-1/2” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105”...
  • Page 51 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-43...
  • Page 52 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 3-5/8” 2-1/4” 2-3/4” 6” 11TH HOLE 9TH HOLE 10TH HOLE 10TH HOLE 9TH HOLE...
  • Page 53 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 9-13/16” 18-3/4” 3-1/4” 8TH HOLE 4TH HOLE 8TH HOLE 4TH HOLE 6TH HOLE 6TH HOLE 6TH HOLE 6TH HOLE...
  • Page 54 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 2-3/4” 2-1/4” 3-5/8” 14TH HOLE 6TH HOLE 13TH HOLE 7TH HOLE 12TH HOLE...
  • Page 55 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-47...
  • Page 56 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 8-13/16” 2-1/16” 2-3/4” 7-3/4” 13TH HOLE 9TH HOLE 10TH HOLE 11TH HOLE 11TH HOLE...
  • Page 57 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 8” 18-3/4” 3-1/4” 3-1/4” 8TH HOLE 5TH HOLE 8TH HOLE 4TH HOLE 6TH HOLE 7TH HOLE 6TH HOLE 6TH HOLE...
  • Page 58 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 7-3/4” 2-3/4” 2-1/16” 8-13/16” 15TH HOLE 6TH HOLE 13TH HOLE 9TH HOLE 13TH HOLE...
  • Page 59 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-51...
  • Page 60 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 3” 4” 3-3/8” 6” 9TH HOLE 10TH HOLE 7TH HOLE 10TH HOLE 5TH HOLE...
  • Page 61 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8” 18-3/4” 3-1/4” 8TH HOLE 5TH HOLE 8TH HOLE 4TH HOLE 6TH HOLE 7TH HOLE 6TH HOLE 6TH HOLE...
  • Page 62 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 3-3/8” 4” 3” 14TH HOLE 3RD HOLE 14TH HOLE 5TH HOLE 12TH HOLE...
  • Page 63 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-55...
  • Page 64 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 9-3/8” 4” 3-3/8” 6” 11TH HOLE 10TH HOLE 7TH HOLE 10TH HOLE 9TH HOLE...
  • Page 65 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8” 18-3/4” 3-1/4” 8TH HOLE 5TH HOLE 8TH HOLE 4TH HOLE 6TH HOLE 7TH HOLE 6TH HOLE 6TH HOLE...
  • Page 66 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 3-3/8” 4” 9-3/8” 14TH HOLE 3RD HOLE 14TH HOLE 7TH HOLE 12TH HOLE...
  • Page 67 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-59...
  • Page 68 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 3-1/4” 3-1/4” 3-1/4” 5-1/8” 8TH HOLE 7TH HOLE 13TH HOLE 7TH HOLE 6TH HOLE...
  • Page 69 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-7/8” 8-7/8” 3-1/4” 11TH HOLE 6TH HOLE 10TH HOLE 7TH HOLE 9TH HOLE 8TH HOLE 8TH HOLE 9TH HOLE...
  • Page 70 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 5-1/8” 3-1/4” 3-1/4” 3-1/4” 11TH HOLE 9TH HOLE 4TH HOLE 11TH HOLE 9TH HOLE...
  • Page 71 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-63...
  • Page 72 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 8-7/8” 3-1/4” 3-1/4” 6-1/4” 10TH HOLE 13TH HOLE 10TH HOLE 5TH HOLE 12TH HOLE...
  • Page 73 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8” 18-3/4” 3-1/4” 8TH HOLE 9TH HOLE 13TH HOLE 5TH HOLE 11TH HOLE 7TH HOLE 6TH HOLE 11TH HOLE...
  • Page 74 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 3-1/4” 3-1/4” 8-7/8” 9TH HOLE 6TH HOLE 14TH HOLE 9TH HOLE 7TH HOLE...
  • Page 75 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-67...
  • Page 76 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 12-7/8” 4-7/8” 13-1/4” 9-1/8” 6-7/8” 12TH HOLE 8TH HOLE 15TH HOLE 8TH HOLE...
  • Page 77 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-7/8” 8-7/8” 3-1/4” 10TH HOLE 7TH HOLE 11TH HOLE 6TH HOLE 8TH HOLE 9TH HOLE 9TH HOLE 8TH HOLE...
  • Page 78 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6-7/8” 9-1/8” 13-1/4” 4-7/8” 12-7/8” 12TH HOLE 11TH HOLE 12TH HOLE 8TH HOLE...
  • Page 79 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-71...
  • Page 80 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 5-3/4” 5-3/4” 5-3/4” 3-1/4” 8-3/16” 6” 13TH HOLE 6TH HOLE 12TH HOLE 5TH HOLE...
  • Page 81 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8” 18-3/4” 3-1/4” 13TH HOLE 5TH HOLE 8TH HOLE 9TH HOLE 11TH HOLE 7TH HOLE 6TH HOLE 11TH HOLE...
  • Page 82 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 8-7/16” 3-1/4” 5-3/4” 5-3/4” 9TH HOLE 8TH HOLE 10TH HOLE 9TH HOLE...
  • Page 83 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-75...
  • Page 84 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 3-1/8” 3-1/8” 3-1/4” 4-1/8” 12TH HOLE 7TH HOLE 7TH HOLE 8TH HOLE 10TH HOLE...
  • Page 85 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-7/8” 8-7/8” 3-1/4” 10TH HOLE 7TH HOLE 11TH HOLE 6TH HOLE 8TH HOLE 9TH HOLE 9TH HOLE 8TH HOLE...
  • Page 86 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 4-1/8” 3-1/4” 3-1/8” 3-1/8” 11TH HOLE 8TH HOLE 12TH HOLE 3RD HOLE 9TH HOLE...
  • Page 87 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-79...
  • Page 88 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 8-3/4” 3-1/8” 3” 6” 10TH HOLE 5TH HOLE 13TH HOLE 10TH HOLE 8TH HOLE...
  • Page 89 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-3/8” 8-3/8” 3-1/4” 13TH HOLE 5TH HOLE 14TH HOLE 9TH HOLE 11TH HOLE 7TH HOLE 12TH HOLE 11TH HOLE...
  • Page 90 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 6” 3” 3-1/8” 8-3/4” 14TH HOLE 9TH HOLE 9TH HOLE 6TH HOLE 12TH HOLE...
  • Page 91 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-83...
  • Page 92 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 13-1/8” 4-7/8” 14-1/4” 8-5/16” 5-7/8” 11TH HOLE 9TH HOLE 15TH HOLE 8TH HOLE...
  • Page 93 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-7/8” 8-7/8” 3-1/4” 10TH HOLE 7TH HOLE 11TH HOLE 6TH HOLE 8TH HOLE 9TH HOLE 9TH HOLE 8TH HOLE...
  • Page 94 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 5-7/8” 8-5/16” 14-1/4” 4-7/8” 13-1/8” 12TH HOLE 11TH HOLE 13TH HOLE 7TH HOLE...
  • Page 95 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-87...
  • Page 96 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 5-5/8” 5-5/8” 3-1/8” 9-3/16” 5” 11TH HOLE 5TH HOLE 12TH HOLE 7TH HOLE...
  • Page 97 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. 3-1/4” 8-3/8” 8-3/8” 3-1/4” 13TH HOLE 5TH HOLE 14TH HOLE 9TH HOLE 11TH HOLE 7TH HOLE 12TH HOLE 11TH HOLE...
  • Page 98 STANDARD SPECIFICATIONS DENOTES USE OF NOTE: FOR PROPER SPIKE HARROW PLACEMENT. BAR CLAMP W/TABS BE SURE TO COUNT BOTH ROUND AND SQUARE (P/N 186200) SPIKE HOLES. CATCH TRAYS POINT INWARD, HOOKS POINT OUTWARD. 5” 9-3/16” 3-1/8” 5-5/8” 5-5/8” 9TH HOLE 7TH HOLE 11TH HOLE 8TH HOLE...

  • Page 99: Assembly Instructions

    Chapter 3 Assembly Instructions It is very important that your new 9650FH Field Cultivator  WARNING be properly assembled, adjusted and lubricated before use. Illustrations in this section show proper assembly Do not attempt to lift heavy parts (such as the procedures.

  • Page 100: Center Frame Assembly- 9650Fh-38', 42', 46' & 50

    Center Frame Assembly- 8. Attach the bottom end of the cylinder lift arms to the oute side of bearing housing mounts with 1 x 2-3/4 9650FH-38’, 42’, 46’ & 50’ bolts and 1 locknuts. IMPORTANT 10. Connect the top end of the cylinder lift arms to the Read all safety precautions at the front of the section radius rod with 1 x 3-1/2 bolts and locknuts.
  • Page 101 5/8 X 2 BOLT, SPRING PIN, 5/8 LOCK NUT 1 LOCK NUT 2 HOLE PLATE GAUGE WHEEL MODELS RADIUS ROD 9650FH-38’-42’ LIFT TUBE ASSEMBLY CULTIVATOR MANIFOLD ASSEMBLY, 1/2 X 4 BOLT, 1/2 LOCK NUT TRANSPORT 4 X 10 LOCK, L-PIN,...

  • Page 102: Center Frame Fold And Depth Control Assembly

    See Figures 3-2. The rectangular hole in the front cylinder mount will be Location of rubber mount for models 9650FH-38’-42’ mounted to the left side of the center frame. and 9650FH-46’-50’ See Figures 3-2, Detail B.
  • Page 103 ASSEMBLY INSTRUCTIONS WING STABILIZER REAR FOLD ASSEMBLY 9650FH-46’-50’, CYLINDER MOUNT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 LOCK NUT 5/8 LOCK NUT DEPTH STOP TUBE ASSEMBLY, 5/8 X 2-1/2 BOLT, 5/8 LOCK NUT DETAIL B...

  • Page 104: Gauge Wheel Assembly Center

    ASSEMBLY INSTRUCTIONS Gauge Wheel Assembly Center 1. Remove the shipping u-bolts and nuts from front of the gauge wheel extension mounts See Figure 3-3. 2. Attach the gauge wheel assemblies to the front of the IMPORTANT center frame with 3/4 x 5-1/2 bolts and 5/8 locknuts. Read all safety precautions at the front of the section 3.
  • Page 105 ASSEMBLY INSTRUCTIONS RADIUS ROD ASSEMBLY 3/4 X 5-1/2 BOLTS & LOCKNUTS 1 X 7-1/2 BOLTS 21” & LOCKNUTS GAUGE WHEEL ASSEMBLIES GAUGE WHEEL EXTENSION MOUNT SHIPPING U-BOLTS & 5/8 NUTS 1 X 7-1/2 BOLTS & LOCKNUTS 6-BOLT TIRE/WHEEL ASSEMBLIES Figure 3-3: Gauge Wheel Assembly Center...

  • Page 106: Hitch Assembly

    ASSEMBLY INSTRUCTIONS Hitch Assembly 3. Insert a 3/4-10 x 7 hex bolt into the hose holder tube on the hitch from the bottom side so the threads point upward. Hold in place with a 3/4-10 flange nut with IMPORTANT the flange pointing upward as well. Do not tighten this Read all safety precautions at the front of the section cap screw, so the hose holder bracket may pivot before attempting any of the following procedures.
  • Page 107 ASSEMBLY INSTRUCTIONS WING NUT HOSE HOLDER CLAMP 1/4-20 X 1 HEX BOLT 3/8-16 X 2 HOSE HOLDER BRACKET HEX NUT 3/4-10 FLANGE NUT STOR-A-WAY HARNESS 3/4-10 X 7 3/8-16 X 3-1/2 HEX BOLT ALL THREAD 1/4-20 LOCK NUT DETAIL A DETAIL A 1-7/16 X 7-1/4 HITCH PIN,...

  • Page 108: Inner Wing Frames

    ASSEMBLY INSTRUCTIONS Inner Wing Frames Wing Gauge Wheel Installation 1. Attach inner wing frames to center frame using 1-1/4 1. Remove the shipping u-bolts and nuts from front of flange bearings, flat washers, 1-1/4 x 6-1/8 pin and the gauge wheel extension mounts See Figure 3-5.
  • Page 109 ASSEMBLY INSTRUCTIONS 1-1/4 X 6-1/8 PINS, FLAT WASHERS 5/16 X 2-1/2 SPRING SLOTTED PINS SHANK ASSEMBLY 1 X 7-1/2 BOLTS RADIUS ROD & LOCKNUTS 21” ASSEMBLY 3/4 X 5-1/2 BOLTS STAND & LOCKNUTS GAUGE WHEEL GAUGE WHEEL ASSEMBLIES EXTENSION MOUNT SHIPPING U-BOLTS &...

  • Page 110: Outer Wing Frames

    ASSEMBLY INSTRUCTIONS Outer Wing Frames NOTE 1. Install outer wing frames to inner wing frames using All tire/wheel assemblies are mounted with the valve 1-1/4-7 x 7 hex head cap screws, and hex lock nuts stem facing outward. See Figure 3-6 Note the direction of bolts as shown in Figure 3-6.
  • Page 111 ASSEMBLY INSTRUCTIONS 1-1/4 X 7 BOLTS, LOCK NUTS 1-1/4 X 7 BOLTS, FLAT WASHERS, LOCK NUTS 3/4 X 5-1/2 BOLTS & LOCKNUTS SHANK 21” 1 X 7-1/2 BOLTS ASSEMBLY & LOCKNUTS RADIUS ROD ASSEMBLY GAUGE WHEEL EXTENSION MOUNT STAND SHANK ASSEMBLY GAUGE WHEEL SHIPPING U-BOLTS...

  • Page 112: Hydraulic Installation

    Outer wing bearing caps do Refer to Figure for hydraulic cylinder installation not require trim. Route rear fold and lift hydraulic models 38’ 9650FH 38’/42’. hoses through bearing caps between frame sections See Figure 3-7.
  • Page 113 CLEVIS & ROLL PINS ROLLER & BUSHING PROVIDED W/CYLINDER CLEVIS & ROLL PINS PROVIDED W/CYLINDER 4 X 16 CYLINDER STOP CYLINDER USED ON MODELS 9650FH-38’-42’ ONLY 3-1/2 X 10 CYLINDER, CLEVIS & ROLL PINS PROVIDED W/CYLINDER Figure 3-9: Fold Cylinder Installation 3-15...
  • Page 114 1/2” X 306” SOCKET PLUG HOSE HOSE 3/8” X 105” 90° #8 3/4-16 MALE HOSE ADAPTER COUPLER 3-1/2 X 10 CYLINDER BLUE HOSE WRAP FRONT OF MACHINE CULTIVATOR MANIFOLD ASSEMBLY DETAIL A Figure 3-10: Hydraulic Lift Installation 9650FH-38’ - 42’ 3-16 F-1090-1120...
  • Page 115 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-17...
  • Page 116 NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-11: Hydraulic Lift Layout 9650FH-38’ - 42’ LH 3-18 F-1090-1120...
  • Page 117 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-12: Hydraulic Lift Layout 9650FH-38’ - 42’ RH 3-19...
  • Page 118 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-20 F-1090-1120...
  • Page 119 #8 TO #8 HOSE ADAPTER CULTIVATOR 8 PORT MANIFOLD MANIFOLD ASSEMBLY #8 TEE 8 PORT ADAPTER FOLD DETAIL B ADAPTER MANIFOLD #8 TEE ASSEMBLY FRONT OF 90° #8 DETAIL A MACHINE ADAPTER Figure 3-13: Hydraulic Fold Installation 9650FH-38’ - 42’ 3-21...
  • Page 120 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-14: Hydraulic Fold Layout 9650FH-38’ - 42’ LH 3-22 F-1090-1120...
  • Page 121 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-15: Hydraulic Fold Layout 9650FH-38’ - 42’ RH 3-23...
  • Page 122 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-24 F-1090-1120...
  • Page 123 ADAPTER COUPLER 3-1/2 X 10 CYLINDER BLUE HOSE WRAP 90° #8 FRONT OF ADAPTER MACHINE 16 PORT MANIFOLD 16 PORT #8 TO #8 LIFT/FOLD ADAPTER MANIFOLD ASSEMBLY DETAIL A 3/4-16 PLUG Figure 3-16: Hydraulic Lift Installation 9650FH-46’ - 50’ 3-25...
  • Page 124 NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-17: Hydraulic Lift Layout 9650FH-46’ - 50’ LH 3-26 F-1090-1120...
  • Page 125 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS AND HOLE OF BEARING CAP WELDMENTS Figure 3-18: Hydraulic Lift Layout 9650FH-46’ - 50’ RH 3-27...
  • Page 126 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-28 F-1090-1120...
  • Page 127 #8 TEE 16 PORT 8 PORT #8 TO #8 ADAPTER LIFT/FOLD FOLD ADAPTER DETAIL B MANIFOLD ADAPTER MANIFOLD ASSEMBLY #8 TEE ASSEMBLY 3/4-16 PLUG FRONT OF 90° #8 MACHINE DETAIL A ADAPTER Figure 3-19: Hydraulic Fold Installation 9650FH-46’ - 50’ 3-29...
  • Page 128 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-20: Hydraulic Fold Layout 9650FH-46’ - 50’’ LH 3-30 F-1090-1120...
  • Page 129 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-21: Hydraulic Fold Layout 9650FH-46’ - 50’’ RH 3-31...
  • Page 130 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-32 F-1090-1120...
  • Page 131 ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART 2-PIN 3-PIN 6-PIN...

  • Page 132: Led Light Installation

    See Figures 3-23 Detail A. 6. Attach the amber light assemblies to the center 12. install the Landoll decal to the rear of the cylinder frame using 1/2 x 2-1/4 u-bolts and lock nuts. The mount rear. amber reflectors should point forward on both 13.
  • Page 133 SIS 20 MPH DECAL, FRONT BOLTS SMV EMBLEM & LOCK NUT 1/4 X 1 BOLTS, RED AG LOCK NUTS LAMP REFLECTOR ASSEMBLY, INCLUDES MOUNT, LANDOLL RED & ORANGE REFLECTOR DECAL TAIL LIGHT DETAIL A LED AMBER MOUNT CYLINDER LIGHT MOUNT ASSEMBLY RH...
  • Page 134 ASSEMBLY INSTRUCTIONS NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE CLAMPS ALONG HYDRAULIC HOSES NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE LOOPS ALONG HYDRAULIC NOTE: SECURE HOSES LIGHT HARNESSES WITH TIES STRAPS AS NEDDED TO KEEP CLEAR OF ANY MOVING PARTS NOTE: RUN LIGHT HARNESS THROUGH HOSE...
  • Page 135 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-37...

  • Page 136: Shank Installation

    ASSEMBLY INSTRUCTIONS Shank Installation NOTE See Figure 2-2 through for shank placement Spring shank assemblies with frame extensions (front dimensions. Verify that all shank clamps and extensions bar) are mounted reversed for narrower shipment. These are properly installed. shanks must be removed and turned forward for proper 1.
  • Page 137 ASSEMBLY INSTRUCTIONS SPRING SHANK ASSEMBLY 5/8 X 4-11/16 X 5-1/2 U-BOLT, 5/8 FLANGE LOCK NUT SPRING SHANK 1/2 X 3-1/4 BOLT, EXTENSION 1/2 LOCK NUT 5/8 X 4-11/16 X 4-3/4 5/8 X 4-11/16 X 7-3/4 U-BOLT, 5/8 FLANGE U-BOLT, 5/8 FLANGE LOCK NUT LOCK NUT 5/8 X 1-3/4 ROUND...

  • Page 138: Row Coil Tine Harrow Installation

    ASSEMBLY INSTRUCTIONS 4 Row Coil Tine Harrow 2. Assemble the coil tine assemblies to the harrow arms. Installation 3. Front row tines are assembled with the tines above Refer to See Figures 2-7 through 2-18 for 4 ow coil tine the stop bolts to prevent damage when shipping harrow placement.
  • Page 139 ASSEMBLY INSTRUCTIONS ANGLE ADJUSTMENT HARROW ADJUSTMENT PIN PLATE GANG BAR MORE LESS PLATE AGGRRESIVE AGGRRESIVE 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (INSTALL BOLT IN INNER BOTTOM HOLE) NOTE: REMVOVE STOP BOLTS AND ROTATE DOWN WITH STOP BOLTS ABOVE TINES 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (INSTALL BOLT IN INNER TOP HOLE)

  • Page 140: Row Coil Tine And Reel Harrow Installation

    ASSEMBLY INSTRUCTIONS 3 Row Coil Tine and Reel Harrow 2. Attach the harrow tine assemblies in correct location with 5/8 spring u-bolts and 5/8 flange lock nuts. Installation 3. Attach reel assemblies to the reel arm assemblies See Figures 2-19 through 2-30 for 3 Row Coil Tine...
  • Page 141 ASSEMBLY INSTRUCTIONS 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT 3/4 X 5-1/2 BOLT, 3/4 LOCK NUT TINE & REEL ASSEMBLY REEL ASSEMBLY HARROW TINE ASSEMBLY 5/8 X 3-11/16 X 4-5/8 U-BOLT, 5/8 LOCK NUT Figure 3-28: 3 Row Coil Tine and Reel Harrow Installation 3-43...

  • Page 142: Row Spike Harrow Installation

    ASSEMBLY INSTRUCTIONS 5 Row Spike Harrow Installation NOTE See Figures 2-31 through 2-42 for 5 Row Spike Harrow See Figures 2-31 2-42 for 5 Row Spike Harrow placement dimensions. placement dimensions of spike harrow arms, spike bars, 1. Attach spike harrow arm assemblies and spike and usage of bar clamps or bar clamps w/ tabs.
  • Page 143 ASSEMBLY INSTRUCTIONS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN SPIKE HARROW ARM ASSEMBLY 3/4-10 X 9 HEX HEAD CAP SCREW CATCH TRAY 1/2-13 X 1-1/4 HEX CAP SCREW 3/4-10 X 5 HEX HEAD CAP SCREW BAR CLAMP W/TABS LYNCH PIN 1/2-13 X 3 HEX HEAD CAP SCREW PULL CHAIN BRACKET...

  • Page 144: Row Spike And Reel Harrow Installation

    “Standard Specification” section. 1. Attach the 3 RSD w/spring and 3 RSD w/o spring (Models 9650FH-38’-42’ only) arm assemblies to the rear tube of the center and wing frames using harrow mounting plates, 3/4-10x5-1/2 hex screws, clamp bushings and 3/4-10 lock hex nut...
  • Page 145 ASSEMBLY INSTRUCTIONS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3 RSD ARM ASSEMBLY 3 RSD ARM W/O SPRING ASSEMBLY 3/4 X 5-1/2 BOLT, W/SPRING HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT 3/4 X 5-1/2 BOLT, FLAT REEL 3/4 LOCK NUT ASSEMBLY CATCH TRAY HOOK...

  • Page 146: Rear Tow Hitch (Option)

    ASSEMBLY INSTRUCTIONS Rear Tow Hitch (Option) 7. Attach the front of the tow hitch assembly to the cultivator frame cross tubes using 5/8-11 x 3-11/16 x 1. Unfold and lower the field cultivator to the ground. 5-1/2 u-bolts and 5/8-11 lock nut. 2.
  • Page 147 ASSEMBLY INSTRUCTIONS NOTE: ROUTE HOSES HOSE CLAMP NOTE: WEIGHT HITCH ALONG OTHER HOSES, PLATE BOLTS TO TOP TRUOUGH HOSE CLAMPS, OF WEIGHT PLATES 3/8-16 X 2-3/4 ALONG CENTER FRAME, ON HITCH, USE HEX BOLT & AND HITCH TO FRONT EXISTING NUTS 3/8-16 LOCK OF MACHINE &...
  • Page 148 ASSEMBLY INSTRUCTIONS 26” 26” NOTE: CENTER REAR TOW HITCH RIGHT REAR TANDEM LIGHT ON CENTER FRAME TAIL LIGHT MOUNT HARNESS MAIN WIRING HARNESS LIGHTING MODULE NOTE: ROUTING OF TANDEM LIGHT HARNESS REAR TOW HITCH ASSEMBLY NOTE: ROUTING OF HYDRAULIC HYDRAULIC HOSES HOSES TANDEM LIGHT HARNESS...

  • Page 149: Operation And Maintenance

      DANGER DANGER Never allow anyone to ride on the 9650FH Field When transporting the unit, place cylinder Cultivator at any time. Allowing a person to ride lockouts in the transport lock position after fully on the machine can inflict serious personal injury extending the cylinders.

  • Page 150: Hydraulic Lift System

    OPERATION AND MAINTENANCE Hydraulic Lift System 1. The rephasing hydraulic lift system contains smaller wing frame cylinders plumbed in series with larger The Field Cultivator is equipped with a rephasing center frame cylinders. It is important that the hydraulic lift system to raise and lower the unit in the field. cylinders be connected in the proper series for the lift system to operate correctly.
  • Page 151 OPERATION AND MAINTENANCE Table provided for general use. NOTES:...

  • Page 152: Hydraulic Fold System

    OPERATION AND MAINTENANCE Hydraulic Fold System 3. The hydraulic fold system is equipped with restrictors in the cylinders to prevent uncontrolled falling of wing The Field Cultivator is equipped with a hydraulic fold frames when folding/unfolding. Removal or improper system to raise and lower the wing frames for narrow assembly of these restrictors can cause the machine transport.
  • Page 153 OPERATION AND MAINTENANCE NOTE: BOTH SIDES ARE EITHER FOLDED OR UNFOLDED DEPENDENT ON OPERATION DETAIL A DETAIL B DETAIL B WING STABILIZER BRACKET MOUNT WING STABILIZER BRACKET MOUNT DETAIL A TRANSPORT LOCK PIN TRANSPORT LOCK PIN STORAGE LOCATION STORAGE LOCATION WHEN UNFOLDED WHEN FOLDED Figure 4-4: Wing Stabilizer Bracket Locks...

  • Page 154: Transporting

    OPERATION AND MAINTENANCE Transporting 3. When towing in combination, the maximum equipment ground speed shall be limited to the 1. Check and follow all federal, state, and local lowest specified ground speed of any of the towed requirements before transporting the Field Cultivator. implements.

  • Page 155: Tractor Preparation

    OPERATION AND MAINTENANCE Tractor Preparation Leveling (Side to Side) The Landoll 9650FH Field Cultivator is designed to be 1. Leveling the Field Cultivator side-to-side involves pulled by tractor equipped with a double lip or clevis type leveling the center frame then leveling the wing hitch.
  • Page 156 RADIUS TUBE Figure 4-6: Leveling from Side to Side 9650FH Gauge Wheels Measure the distance from the top of the wing frame to the top of the walking beam spindle. Lay a 1. The front gauge wheels of the floating hitch cultivator...
  • Page 157 OPERATION AND MAINTENANCE RH & LH LOCKING NUTS 1/2” LOCKING SET SCREW 21” MEASURE RADIUS ROD 1-1/2” LESS TUBE WALKING BEAM GAUGE WHEEL SPINDLE (TOP) SPINDLE (TOP) Figure 4-7: Gauge Wheel Adjustment To adjust the gauge wheel radius rod, loosen both the rightand left-hand threaded locking nuts.

  • Page 158: Depth Stop Adjustment

    OPERATION AND MAINTENANCE Depth Stop Adjustment LED Light Operation 1. The operating depth of the Field Cultivator is 1. Attach the seven-pin plug to the socket at the rear of controlled by a single-point depth stop. The stop is the tractor. The socket must be in good working located at the center front of the machine order, and free of dirt, grease, and corrosion.

  • Page 159: Spring Shank

    OPERATION AND MAINTENANCE Spring Shank 5/8 X 3 BOLT 1. The Field Cultivator may be equipped with spring 1/8” shanks. The spring shanks feature a 185 lb. point SPRING PLATE load and a 10” trip height to clear field obstructions. Shanks are 5/8 x 1-3/4 heat treated steel.

  • Page 160: Wheel Bearing Maintenance

    OPERATION AND MAINTENANCE Wheel Bearing Maintenance NOTE Wheel bearing maintenance should be performed at the The triple-lip seals should point away from the hub to beginning of every season of use. Check the wheel keep contaminants out and allow grease to pass bearings periodically for excessive end play.

  • Page 161: Lubrication

    OPERATION AND MAINTENANCE Lubrication 1. A proper maintenance schedule will insure a long operating life and peak performance. Performing the following lubrication will ensure maximum operating life of the Field Cultivator See Table 4-1 Figure 4-11. 2. When lubricating the Field Cultivator, SAE multi-purpose EP grease, or EP grease with 3-5% molybdenum sulfide is recommended.
  • Page 162 OPERATION AND MAINTENANCE Figure 4-11: Lubrication Points LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Gauge Wheel Radius Rod 1 each Gauge Wheel Hubs 1 each Gauge Wheel Weldment Hubs 1 each Walking Beam 1 each Lift Hubs 1 each Lift Radius Rod...
  • Page 163 OPERATION AND MAINTENANCE Table provided for general use. NOTES: 4-15...

  • Page 164: Row Coil Tine Harrow Adjustments

    OPERATION AND MAINTENANCE 4 Row Coil Tine Harrow 2. In general tine harrows have better capabilities for handling more residue and wetter conditions. When Adjustments operating the coil tine harrow, a more vertical tine tooth angle will make the harrow more aggressive. A 1.
  • Page 165 OPERATION AND MAINTENANCE 1-8 HEX NUTS ANGLE ADJUSTMENT PLATE SPRING HARROW ADJUSTMENT PIN ASSEMBLY MORE LESS AGGRRESIVE AGGRRESIVE 1-1/32” 22” 1/2 X 1-1/4 RD HEAD SQ NECK SCREW (PLACE BOLT IN INNER BOTTOM HOLE) 1/2 X 1-1/4 RD HEAD SQ GANG BAR NECK SCREW (PLACE BOLT IN INNER PLATE...

  • Page 166: Row Coil Tine And Reel Adjustments

    OPERATION AND MAINTENANCE 3 Row Coil Tine and Reel 4. Each coil tine harrow may be adjusted for spring pressure as well See Figure 4-13. Raise the tine Adjustments harrow off the ground. Remove the clevis pin from the spring tube and install in a heavy or light setting 1.
  • Page 167 OPERATION AND MAINTENANCE SPRING ASSEMBLY MORE LESS 1-8 HEX NUTS AGGRRESIVE AGGRRESIVE 1/2” 21-3/4” REEL ASSEMBLY HEAVY CLEVIS PIN LIGHT HARROW ADJUSTMENT PIN CLEVIS PIN HARROW ADJUSTMENT PIN REEL 3 ROW COIL TINE ASSEMBLY ASSEMBLY HARROW ADJUSTMENT HOLES Figure 4-13: 3 Row Coil Tine and Reel Adjustments 4-19...

  • Page 168: Row Spike Harrow Adjustments

    OPERATION AND MAINTENANCE 5 Row Spike Harrow 2. For the most aggressive spike to action, install the harrow adjustment pin in the forward mounting hole Adjustments over each bar clamp for each spike bar Figure 4-14. This will position the spike teeth to be in 1.
  • Page 169 OPERATION AND MAINTENANCE LEAST MIDDLE MOST CARRYING CHAIN TOOTH ANGLE TOOTH ANGLE TOOTH ANGLE CLEVIS PIN FORWARD PULL CHAIN SPIKE BAR ASSEMBLY BAR CLAMP W/TABS CLEVIS PIN BAR CLAMP Figure 4-14: 5 Row Spike Harrow Adjustments 4-21...

  • Page 170: Row Spike And Reel Adjustments

    OPERATION AND MAINTENANCE 3 Row Spike and Reel 5. The 12” diameter reel consists of nine 3/4” diameter round bars with a chevron shape for smoother Adjustments rotation. The reels have no inner shaft to reduce plugging in wetter conditions. The reels operate 1.
  • Page 171 OPERATION AND MAINTENANCE STORAGE/LEAST TOOTH ANGLE MIDDLE TOOTH ANGLE SPRING SPRING CARRYING CHAIN MOST TOOTH ANGLE ASSEMBLY ASSEMBLY 1-8 HEX NUTS 21-3/4” REEL ASSEMBLY FORWARD PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP BAR CLAMP W/TABS FLAT REEL ASSEMBLY SPIKE BAR ASSEMBLY CLEVIS PIN REEL...

  • Page 172: Storage

    OPERATION AND MAINTENANCE Storage 1. The service life of the Field Cultivator will be extended by proper off-season storage practices. Prior to storing the unit, complete the following procedures: a. Completely clean the unit. b. Inspect the machine for worn or defective parts. Replace as needed.

  • Page 173: Troubleshooting Guide

    Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 9650FH Field Cultivator. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM...
  • Page 174 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION SWEEPS NOT CUTTING, LEAVING Shanks not positioned correctly Check for proper shank placement SKIPS Sweeps not wide enough Use wider sweeps Sweeps set too shallow Increase operating depth Incorrect sweep angle Use 47 degree sweeps Incorrect shank spring adjustment Adjust spring shank.
  • Page 175 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 06/09/2020 F-1090 New Manual 11/20/2020 F-1090-1120 Initial release...
  • Page 176 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 9650FH Field Cultivator Operator’s Manual Re-Order Part Number F-1090-1120 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

Table of Contents