Advertisement
Quick Links
Operation Manual
Bench-Type Circular Saw
61950
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61950
Summary of Contents for WilTec 61950
- Page 1 Operation Manual Bench-Type Circular Saw 61950 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
- Page 2 All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 ◦ Do not use the electric tool for purposes for which it is not intended. For example, do not use hand-held circular saws for the cutting of branches or logs. © by WilTec Wildanger Technik GmbH Item 61950 Page 3 http://www.WilTec.de...
- Page 4 All parts must be correctly mounted and all conditions must be fulfilled to ensure fault-free operation of the electric tool. ◦ The moving protective hood may not be fixed in the open position. © by WilTec Wildanger Technik GmbH Item 61950 Page 4 http://www.WilTec.de...
- Page 5 Only use saw blades for which the maximum permissible speed is not lower than the maximum spindle speed of table saws and which are suitable for the material to be cut. © by WilTec Wildanger Technik GmbH Item 61950 Page 5 http://www.WilTec.de...
- Page 6 • Only use the supplied saw blade for sawing operations in wood, materials similar to wood, plas- tics and non-ferrous metals (except for magnesium and alloys containing magnesium). © by WilTec Wildanger Technik GmbH Item 61950 Page 6 http://www.WilTec.de http://www.aoyue.eu...
- Page 7 Layout and items supplied Layout © by WilTec Wildanger Technik GmbH Item 61950 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 Remove the packaging material and any packaging and/or transportation braces (if available). • Check to see if all items are supplied. • Inspect the device and accessories for transport damage. © by WilTec Wildanger Technik GmbH Item 61950 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 9 The device is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this. © by WilTec Wildanger Technik GmbH Item 61950 Page 9 http://www.WilTec.de...
- Page 10 25 % of the cycle at the specified rating and must then be allowed to idle for 75 % of the cycle. © by WilTec Wildanger Technik GmbH Item 61950 Page 10 http://www.WilTec.de...
- Page 11 • Before you actuate the on/off switch, make sure that the saw blade is correctly fitted and that the moving parts of the device run smoothly. © by WilTec Wildanger Technik GmbH Item 61950 Page 11 http://www.WilTec.de http://www.aoyue.eu...
- Page 12 Remove the saw blade guard (4). • Remove the screws (19). • Take out the worn table insert (2). • To fit the replacement table insert, proceed in reverse order. © by WilTec Wildanger Technik GmbH Item 61950 Page 12 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 13 The procedure for changing over to the higher guide face is similar. • Cutting width ◦ The parallel stop (15) has to be used when you make longitudinal cuts in wooden work- pieces. © by WilTec Wildanger Technik GmbH Item 61950 Page 13 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 14 The guard hood must always be lowered over the workpiece. • When you make a longitudinal cut, never adopt a working position that is in line with the cutting direction. © by WilTec Wildanger Technik GmbH Item 61950 Page 14 http://www.WilTec.de http://www.aoyue.eu...
- Page 15 Wipe the device with a clean cloth or blow it with compressed air at low pressure. • We recommend that you clean the device immediately each time you have finished using it. © by WilTec Wildanger Technik GmbH Item 61950 Page 15 http://www.WilTec.de...
- Page 16 Store the device and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 ℃ and 30 ℃. Store the electric tool in its original packaging. © by WilTec Wildanger Technik GmbH Item 61950 Page 16 http://www.WilTec.de...
- Page 17 Illustrative images concerning the assembly © by WilTec Wildanger Technik GmbH Item 61950 Page 17 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 18 © by WilTec Wildanger Technik GmbH Item 61950 Page 18 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 19 This logo indicates that this electric device must not be disposed with the do- mestic waste. The company WilTec Technik GmbH has been registrated in the German registry EAR under the WEEE- registration number DE45283704. Disposal of used electrical and electronic appliances...