Advertisement
Quick Links
Operation Manual
Circular Saw
61123
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificant-
ly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for WilTec 61123
Summary of Contents for WilTec 61123
- Page 1 Operation Manual Circular Saw 61123 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificant- Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Make sure that the laser is always aimed at a stable workpiece without a reflective surface, e.g., wood or rough surfaces. Bright and reflective surfaces such as steel are not suitable for use with the laser. The beam can be reflected onto the user. © by WilTec Wildanger Technik GmbH Item 61123 Page 3 http://www.WilTec.de...
- Page 4 Use screw clamps or other practical means to secure and support the workpiece on a stable platform. Holding the workpiece by hand or against the body is unstable and can lead to loss of control. © by WilTec Wildanger Technik GmbH Item 61123 Page 4 http://www.WilTec.de...
- Page 5 Never try to remove the saw from the workpiece or to pull the saw backwards while the saw blade is moving, as this could result in kickback. © by WilTec Wildanger Technik GmbH Item 61123 Page 5 http://www.WilTec.de...
- Page 6 Use the retractable handle to lift the lower guard and make sure that it moves freely and does not touch the blade or other parts at all angles and cutting depths. © by WilTec Wildanger Technik GmbH Item 61123 Page 6 http://www.WilTec.de...
- Page 7 Release button Clamp for adjusting the cutting depth with Switch locking lever Saw blade clamping screw with washer Soft grip Cutting depth scale Storage for hexagon key © by WilTec Wildanger Technik GmbH Item 61123 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 3. Tighten the set screw to secure it in place. 4. Make sure that the edge guide lies against the wood over the entire length in order to achieve an even parallel cut. © by WilTec Wildanger Technik GmbH Item 61123 Page 8 http://www.WilTec.de...
- Page 9 3. When the finish line is reached, lift the tool off the work surface before turning it off. If there is a lot of dust, leave the saw on for some few seconds to allow the dust to clear from inside the tool. © by WilTec Wildanger Technik GmbH Item 61123 Page 9 http://www.WilTec.de...
- Page 10 The tool shakes abnormally and is accompanied by a strange noise. • The motor casing becomes unusually hot. • There are strong sparks in the engine area. © by WilTec Wildanger Technik GmbH Item 61123 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 11 Technical specifications Tension (V) Frequency (㎐) Power (W) Current rating (A) Idle speed (rpm) 4500 blade size (㎜) soft wood 28.5 Max. cutting depths (㎜) tile aluminium © by WilTec Wildanger Technik GmbH Item 61123 Page 11 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 12 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.
Need help?
Do you have a question about the 61123 and is the answer not in the manual?
Questions and answers