Table of Contents
Advertisement
Quick Links
Operation Manual
Bench-type circular saw
ARTICLE 61950
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 24
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Table of Contents
Related Manuals for WilTec 61950
Summary of Contents for WilTec 61950
- Page 1 Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 24 http://www.WilTec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram.
- Page 3 – When working outdoors, anti-slip footwear is recommended. – Tie long hair back in a hair net. 9. Use protective equipment – Wear protective goggles. – Wear a mask when carrying out dust-creating work. © by WilTec Wildanger Technik GmbH Seite 26 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 4 All parts must be correctly mounted and all conditions must be fulfilled to ensure fault-free operation of the electric tool. – The moving protective hood may not be fixed in the open position. © by WilTec Wildanger Technik GmbH Seite 27 http://www.WilTec.de http://www.aoyue.eu...
-
Page 5: Additional Safety Instructions
– Make sure that the riving knife is always used, and set up is correctly. – Use the upper blade guard and set it to the correct position. © by WilTec Wildanger Technik GmbH Seite 28 http://www.WilTec.de http://www.aoyue.eu... - Page 6 12 Only use the supplied saw blade for sawing opera-tions in wood, materials similar to wood, plastics and non-ferrous metals (except for magnesium and alloys containing magnesium). © by WilTec Wildanger Technik GmbH Seite 29 http://www.WilTec.de http://www.aoyue.eu...
-
Page 7: Layout And Items Supplied
• Check to see if all items are supplied. • Inspect the equipment and accessories for transport damage. • If possible, please keep the packaging until the end of the guarantee period. © by WilTec Wildanger Technik GmbH Seite 30 http://www.WilTec.de http://www.aoyue.eu... -
Page 8: Proper Use
AC motor ......220- 240V ~ 50Hz Power..S1 1800W S6 25% 2000W Idle speed n0 ......... 5000 min -1 Cutting-off wheel ....... Ø 250 x Ø16 - 30 x 2 - 4 mm © by WilTec Wildanger Technik GmbH Seite 31 http://www.WilTec.de http://www.aoyue.eu... -
Page 9: Before Starting The Equipment
© by WilTec Wildanger Technik GmbH Seite 32 http://www.WilTec.de http://www.aoyue.eu... - Page 10 • Remove the 1 countersunk head screws (17). • Take out the worn table insert (6). • To fit the replacement table insert, proceed in reverse order. 6.5 Fitting/replacing the blade (Fig. 4) © by WilTec Wildanger Technik GmbH Seite 33 http://www.WilTec.de http://www.aoyue.eu...
-
Page 11: Using The Saw
• The parallel stop (7) has to be mounted in the guide rail (28) of the saw table (1). • The parallel stop (7) can be set to the required dimension with the help of the scale (22) on the guide rail (1). © by WilTec Wildanger Technik GmbH Seite 34 http://www.WilTec.de http://www.aoyue.eu... -
Page 12: Operation
• Always push the workpiece through to the end of the splitter (5). • The offcut piece remains on the saw table (1) until the blade (4) is back in its position of rest. © by WilTec Wildanger Technik GmbH Seite 35 http://www.WilTec.de... - Page 13 10.2 Carbon brushes In case of excessive sparking, have the carbon brushes checked only by a qualifi ed electrician. Danger! The carbon brushes should not be replaced by anyone but a qualified electrician. © by WilTec Wildanger Technik GmbH Seite 36 http://www.WilTec.de http://www.aoyue.eu...
- Page 14 Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging. © by WilTec Wildanger Technik GmbH Seite 37 http://www.WilTec.de http://www.aoyue.eu...
- Page 15 © by WilTec Wildanger Technik GmbH Seite 38 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 16 © by WilTec Wildanger Technik GmbH Seite 39 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 17 © by WilTec Wildanger Technik GmbH Seite 40 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 18 © by WilTec Wildanger Technik GmbH Seite 41 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 19 © by WilTec Wildanger Technik GmbH Seite 42 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 20: Disposal Regulations
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.