Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Spartus 45PFC
Summary of Contents for Spartus 45PFC
- Page 1 Plasma cutter SPARTUS® ProCUT 45PFC User’s manual...
- Page 2 Therefore, our offer covers such a wide assortment of products. Thank you very much for your trust in our company. We would like to invite you to familiarize yourself with the remaining products and offer at www.spartus. info or directly at a local distributor of SPARTUS® products.
-
Page 3: Table Of Contents
7.8 CNC connector ..................................16 7.9 The process of cutting ................................16 7.10 The table below for the shift and scale selection ..................... 16 7.11 Recommended SPARTUS® SP45H plasma torch ....................... 18 8. MAINTENANCE ............................19 9. ENVIRONMENTAL PROTECTION ......................19 10. -
Page 4: Safe Use - Hazards Associated With Arc Welding And Plasma Cutting
USER’S MANUAL 1. SAFE USE – HAZARDS ASSOCIATED WITH ARC WELDING AND PLASMA CUTTING Arc welding and plasma cutting are processes feeder fitted with spool and harness). Care that can pose hazards for the operator and per- shall be taken during manual handling. sons in his vicinity. -
Page 5: Welding Arc Radiation Can Be Dangerous
USER’S MANUAL • Power supply must never be connected Such radiation can be direct or reflected from before the accessories of SK sockets/con- surfaces such as bright metals and light colo- nectors are properly installed in the device. ured objects. •... -
Page 6: Noise Can Be Harmful
USER’S MANUAL Arc welding and allied processes produce wel- in case of an emergency, are in the imme- ding fume which may pollute the atmosphere diate vicinity. surrounding the work. Welding fume is a vary- • In closed rooms or in certain circumstances ing mixture of airborne gases and fine particles during outdoor operations, it may be re- which, if inhaled or swallowed, constitute a... -
Page 7: Fire Or Explosion Hazard
USER’S MANUAL source, observed for an adequate period after its c) effective maintenance of sound protection termination. devices, • „Hot spots” and immediate surroundings d) indication as „ear protection areas” where should be observed until their temperature applicable, has dropped to normal. e) restriction of entry to these „ear protection 1.6.2 Explosion hazard areas”... -
Page 8: Other Hazards
USER’S MANUAL 1.7.4 Moving elements can be dangerous cylinder valve socket when the valve is being opened. • Special valve shield should always be in- stalled during cylinder transportation or when the cylinder is not used. OTHER HAZARDS Arc welding and allied processes carrying other All protective elements and device housing hazards not listed before. -
Page 9: Symbols Used In Instructions
USER’S MANUAL 1.9 EXTRA PRECAUTIONS 1.9.1 Potential risk during plasma cutting • during the plasma cutting – plasma arc temperature exceeds several thousand °C, • large light radiation is accompanied when plasma cutting as a result of burning gases and the igniting of a plasma arc, •... -
Page 10: Electromagnetic Compatibility (Emc)
Methods of reducing electromagnetic interference are listed in detail in the standard EN 60974-9 „Arc welding equipment – Part 9: Installation and use”. 4. CONFORMITY WITH STANDARDS The SPARTUS® ProCUT 45PFC plasma cutter is in conformity with the relevant Union harmoni- zation legislation: LVD 2014/35/UE... -
Page 11: Ce Marking
In addition, the cutter is equipped with a 2T / 4T mode selector switch. SPARTUS® ProCUT 45PFC is professional plasma cutter that will find application in manufacturing sectors, industry and as source of CNC plasma tables. -
Page 12: Technical Parameters Of Device
600 × 215 × 405 7. INSTALLATION AND USE WARNING! SPARTUS® ProCUT 45PFC machine is intended for professional and industrial applications. Installation and use of the device may only be carried out appropriately trained professionals. Qualified person (def.) A person who has gained the relevant technical education, training took place and / or gained... -
Page 13: Proper Cooling
USER’S MANUAL 7.1 PROPER COOLING The unit should be placed stable on a dry and flat surface. Avoid too much slope and slippery surfaces. Check regularly that the vents (inlet, outlet) are not covered. The minimum distance between the machine vents and walls should be 50 [cm]. 7.2 MOVEMENT AND HANDLING Please take special care when moving the machine. -
Page 14: Connecting To Power Supply
USER’S MANUAL 7.4 CONNECTING TO POWER SUPPLY Requirements for power network parameters (voltage, permissible range of mains voltage fluctuations etc.) are given in the table with technical parameters of device and on the rating plate of cutter. Before connecting the unit to the power source: •... -
Page 15: Control Panel
USER’S MANUAL Compressor Power cable Elements of air filtration and air preparation in installation Plasma torch Cutting material Work clamp Control cable 7.6 CONTROL PANEL 8.105RM.320-A Screen Cutting current knob Mode switch 2T / 4T Air check key... - Page 16 USER’S MANUAL 7.6.1 Description of parameters on the display Current display Operating mode 2T / 4T Air check display 2T / 4T mode 2T mode To start cutting press the microswitch, to start the plasma arc. Releasing the microswitch will stop the cutting process. Pre Gas Post Gas Gun switch...
-
Page 17: Central Connector - Setup Of Pins
USER’S MANUAL AIR CHECK DISPLAY Press the air check key „PRESSURE” to check whether the air passage is smooth. If the machine is working properly, the screen will display the air pressure value normally. E12 „Lack of gas” message informs about the lack of air flow. Lack of gas OTHER MESSAGES „E01 Overheat”... -
Page 18: Cnc Connector
USER’S MANUAL 7.8 CNC CONNECTOR ProCUT 45PFC plasma cutter is designed to work as a plasma source in cooperation with CNC tables. Communication between CNC table and plasma cutter is performed by using a special CNC control socket. Diagram how to connect CNC control socket. - Page 19 USER’S MANUAL Scale selection VOLTAGE DIVIDER 20:1 30:1 40:1 50:1 Number...
-
Page 20: Recommended Spartus® Sp45H Plasma Torch
USER’S MANUAL 7.11 RECOMMENDED SPARTUS® SP45H PLASMA TORCH (standard TRAFIMET® S45) patent pending SPARE PARTS CODE DESCRIPTION 09600 Hand torch head (to 25A) 09602 Hand torch head (to 40A) 09605 Handle with microswitch (set) 07301.20 Microswitch 52531 Electrode 60028 Swirl ring Tip ϕ... -
Page 21: Maintenance
USER’S MANUAL 8. MAINTENANCE WARNING! Before performing any maintenance or repairing of device, it should be disconnect from the power source and wait at least 5 minutes. The voltage accumulated in capacitors should be discharged at this time to a safe level. But even after that operation you should be careful. Maintenance and repair work may be performed only by qualified personnel with the appropriate per- missions. -
Page 22: Troubleshooting
10. TROUBLESHOOTING Not all problems with functioning of the device, are the evidence of failure. You can independently carry out an analysis in search of probable failure. In case of doubt, please contact to SPARTUS® dealer or authorized service center. - Page 23 A masterly combination of high quality production, excellent parameters and ergonomics – these are fea- tures of the SPARTUS® Master series of devices, which were created with demanding welding jobs in mind. Precision, functionality, excellent parameters and resistance to high workloads –...
- Page 24 Videopresentation of products Subscribe to the channel SPARTUS.INFO...
Need help?
Do you have a question about the 45PFC and is the answer not in the manual?
Questions and answers