GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Precautions Precautions Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip "You have entered the area of electronic surveillance" in an eye- catching place.
Page 4
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged. Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
Page 5
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device. Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Overview 1.1 Principle of Thermal Imaging and Advantages Any object with temperature higher than the absolute zero (-273.15°F) will emit infrared (IR) ray, even though it does not emit light. The IR ray is also called thermal radiation.
Page 8
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Figure 1-1 Appearance and interfaces of the all-in-one thermal imaging IP camera Table 1-1 Appearance and interface description Physical Description Interface Press and hold this button for three seconds to restore RESET factory settings. Default value: 192.168.0.120...
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions 1.3 Wiring Diagram Figure 1-2 shows the multi-connector cable of the all-in-one thermal imaging IP camera and Table 1-2 describes the multi-connector cable. Figure 1-2 Multi-connector cable Table 1-2 Multi-connector cable description...
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Core Function Description Input audio signal and receive analog Audio input (line audio signal from audio pickup and input) other devices. Connect with sound box and other Audio output external audio devices. Brown wire...
Page 11
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Adopts watchdog for hardware and software and supports automatic fault rectification. Adopts metal housing design that supports heat dissipation. Uses a three-shaft rotational structure that facilitates installation and adjustment.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Device Dimensions Figure 2-1 shows the dimensions of the all-in-one thermal imaging IP camera. Figure 2-1 Dimensions (unit: mm) Issue V1.0 (2016-02-22)
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Device Installation 3.1 Installation Preparation When installing the camera, you may require the following tools and accessories listed in Table 3-1. You need to prepare only listed tools as accessories are delivered with the camera.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Tool Appearance Swell plastic buttons(delivered with the camera) 3.2 Installation Method The all-in-one thermal imaging IP camera can be installed on ceiling/wall, based on user requirement. For cement wall, install expansion screws (the installation hole must be consistent with the bracket) and then install the bracket.
Page 15
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Figure 3-1 Installing the locating sticker Locating sticker Wall Step 2 Drill four 5 mm holes on the ceiling/wall at the positions marked by the sticker. Step 3 Secure the bottom base onto the wall, as shown in Figure 3-2:...
Page 16
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Figure 3-3 Pushing the camera to the bottom base Step 5 Wire the camera and hide the visible cables. After the wiring, rotate the camera to make the camera align with the bottom base, as shown in Figure 3-4:...
Page 17
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Figure 3-5 Securing the camera to the bottom base Step 7 Align the focus fixture with the lens slot to make sure they are clipped together. Hold the handle and make adjustment towards the direction indicated by the arrow, as shown...
Page 18
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Figure 3-7 Adjusting the shooting angle Screw 3 Screw 2 Screw 1 1. Loosen screw 1 and adjust part 1 towards the direction indicated by the arrow; adjustable range: 360° 1. Loosen screw 2 and adjust part 2 towards the direction indicated by the arrow;...
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Quick Configuration 4.1 Login and Logout You must use Internet Explorer 6 or a later version to access the web management system; otherwise, some functions may be unavailable. Login system Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value: 192.168.1.168) in the address box, and press Enter.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Step 3 Click Login. The main page is displayed. logout To logout of system, click Sign out in the upper right corner of the main page, the login page is display after you log out of the system.
Page 21
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Table 4-1 Web interface description Name Description Show live video and allow users to configure frontend Live video parameters. Parameter Configure device parameters, including device information, configuration audio/video stream, alarm, and privacy masking.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual 4.3 Browsing Video User can browse the real-time video in the web management system. Preparation To ensure the real-time video can be play properly, you must perform the following operation when you log in to the web for the first time: 1.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Figure 4-4 Configuring ActiveX control and plug-ins 3. Download and install the player control as prompted. The login page is display when the control is loaded. 4.3.1 Download the right control in the Internet Explorer Real-time video page pop-ups the message clicks to play live video with ActiveX control to reduce latency.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual 4.4 Setting Local Network Parameters Description Local network parameters include: IP protocol IP address Subnet mask Default gateway Dynamic Host Configuration Protocol (DHCP) Preferred Domain Name System (DNS) server ...
Page 25
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Parameter Description Setting Subnet Mask Subnet mask of the network [Setting method] adapter. Enter a value manually. [Default value] 255.255.255.0 Default Gateway This parameter must be set if [Setting method] the client accesses the device Enter a value manually.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Parameter Configuration 5.1 Accessing the Sensor Setting Interface Operation procedure: Step 1 On the web interface or client interface, right-click a monitoring screen, as shown in Figure 5-1: Figure 5-1 Sensor Setting interface Step 2 Choose Sensor Setting and the Sensor Setting dialog box appears.
Page 27
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Figure 5-2 Image setting interface Table 5-1 describes the image setting parameters. Table 5-1 Image setting parameter description Parameter Description Configuration Method The temperature field of a scenario detected by the thermal imaging camera will be mapped to the value range 0~255 by algorithm processing.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Parameter Description Configuration Method Select a proper DVE mode based on the [Configuration contrast and detail characteristics of the image method] shown. Available DVE modes include: Select from the drop- DVE Mode ...
Page 29
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Table 5-2 describes the FFC mode parameters. Table 5-2 FFC mode parameter description Parameter Description Configuration Method The thermal imaging camera contains a mechanical correction actuator to periodically improve image quality. This actuator is called flat field correction (FFC). During...
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Parameter Description Configuration Method [Configuration method] Drag the slide interval In auto FFC mode, FFC interval range: 5~30 min (min) [Default value] In manual or external FFC mode, the camera will not Trigger...
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Table 5-3 DNR parameter description Parameter Meaning Configuration Method [Configuration method] Select from the drop-down list 3D NR Reduce noise of image. [Default value] [Configuration method] Select from the drop-down list 2D NR Reduce noise of image.
Page 32
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Figure 5-6 Screen adjustment interface Table 5-4 Screen adjustment parameter description Parameter Meaning Configura tion Method Compared with images generated based on visible light, IR images boast the features of high background and low contrast.
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Technical Specifications Table 6-1 describes the technical specifications of the all-in-one thermal imaging IP camera. Table 6-1 Technical specification Item Parameter Description Detector type Non-cooling IR focal plane sensor Sensing method Microbolometer...
Page 34
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Item Parameter Description Feature mode image 0~6 levels enhancement Correction Manual/Auto/External Noise reduction Support,2D/3D Contrast 1~4 levels adjustment Mirroring Support OSD display Support Output image D1/CIF Image resolution feature Frame rate 30fps Video H.264BP/MP/HP/MJPEG...
Page 35
GANZ ZNT8-BA1Fxx-T Thermal Network Camera User Manual Precautions Item Parameter Description features interface Audio interface 1 audio input and 1 audio output Alarm interface 2 alarm input and 2 alarm output Analog video BNC,750hm output interface control RS485 interface SD card interface...