Table of Contents
Advertisement
Available languages
Available languages
EN
6. Do not overwork yourself. Take regular breaks to ensure you can concentrate on the work and have full control over the product.
WARNING! In some countries regulations define at what time of the day and on what special days products are allowed to be used and what restrictions
apply! Ask your community for detailed information and observe the regulations in order to preserve a peaceful neighbourhood and avoid committing
administrative offences!
Tilling
1. Make sure that the working area is clear of stones, sticks, wire or other objects that could damage the product or its engine.
2. Do not till very wet soil because it tends to stick to the working tool preventing the proper rotation, and it could also cause you to slip and fall.
3. Always maintain a firm grip on the product. For better guidance apply light pressure to the handles (1) (Fig. 10).
WARNING! Never carry this product as the person in Fig.11 is doing. If you do, and the tines engage, you could suffer serious injury.
4. Do not try to till too deeply or force the product into soil that is extremely hard or resistant.
5. Walk the product through the soil at a normal pace and in as straight a line as possible.
6. Till in slight overlapping rows. The most effective pattern for tilling soils is moving the product up and down in verticals lines, then move the product in
horizontal lines from left to right (Fig.12). This will keep the rows even and ensures that all the ground is tilled without missing any spots.
7. Pay special attention when changing direction. Apply light pressure onto the handle (1) so that the tines (13) are lifted to make a turn. Turn the product
around guided by the wheels (11).
Gradually release pressure and move the tines (13) back to the ground.
WARNING! Stop the motor, if the product strikes a foreign object! Switch the product off, disconnect it from the power supply and let it cool down. Inspect
the product thoroughly for damage! Have any damage repaired before restarting!
Extensive vibration of the product during operation is an indication of damage! Stop the motor. The product should be promptly inspected and repaired!
After use
1. Switch the product off, disconnect it from the power supply and let it cool down.
2. Check, clean and store the product as described below.
Maintenance
WARNING! Always switch the product off, disconnect the product from the power supply and let the product cool down before performing inspection, main-
tenance and cleaning work!
1. Keep the product clean. Remove debris from it after each use and before storage.
2. Regular and proper cleaning will help ensure safe use and prolong the life of the product.
3. Inspect the product before each use for worn and damaged parts. Do not operate it if you find broken and worn parts.
WARNING! Only perform repairs and maintenance work according to these instructions! All further works must be performed by a qualified specialist!
Cleaning
1. Clean the product with a dry cloth. Use a brush for areas that are hard to reach.
2. In particular clean the air vents (16) after every use with a cloth and brush.
3. Remove stubborn dirt with high pressure air (max. 3 bar).
NOTE: Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfectants to clean this product as they might be harmful to its surfaces.
4. Check for worn or damaged parts. Replace worn parts as necessary or contact an authorised service centre for repair before using the product again.
Repair
This product does not contain any parts that can be repaired by the consumer. Contact an authorised service centre or a similarly qualified person to have it
checked and repaired.
Storage
1. Switch the product off and disconnect it from the power supply.
2. Clean the product as described above.
3. Store the product and its accessories in a dark, dry, frost-free, well-ventilated place.
4. Always store the product in a place that is inaccessible to children. The ideal storage temperature is between 10°C and 30°C.
5. We recommend using the original package for storage or covering the product with a suitable cloth or enclosure to protect it against dust.
Transportation
1. Switch the product off and disconnect it from the power supply.
2. Attach transportation guards, if applicable.
3. Always carry the product by its transportation handle (17).
4. Protect the product from any heavy impact or strong vibrations which may occur during transportation in vehicles.
5. Secure the product to prevent it from slipping or falling over.
9
WWW.NAKAYAMATOOLS.COM
Advertisement
Table of Contents
