Advertisement
Quick Links
Assembly Instructions
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for purchasing Spectrum products!
Before you begin, please make sure all parts and proper quanti-
ties are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding
damages or if you have any questions, please call 1-800-235-1262.
Phillips screwdriver
4mm hex wrench
Note: The worksurface halves must be assembled prior to the table assembly shown here. Refer to
the assembly instructions included with the worksurface halves (Box #1) for assembly procedure.
(1) 0112522
front leg assembly
(1) bottom panel
0112496 - 84" tables
0112541 - 60" tables
glide wrench
(included)
(included)
Leg Assemblies (Box #2)
(1) 0112535
rear leg assembly
(with grommet hole)
Cord Channel (Box #3)
(4) cord channel rail
0112495 - 84" tables
0112540 - 60" tables
™
InVision
Media Collaboration Table
48" x 60" - #37102
48" x 84" - #37103
60" x 60" - #37104
60" x 84" - #37105
(26) 035728
1/4-20 x 1/2" PHMS
(8) 0100167
8-32 x 1/2" PH
thread-cutting screw
(16) 059534
1/4-20 x 30mm JC bolt
(8) 041289
1/4-20 x 1-3/4" PHMS
(2) 059899
1/4-20 x 45mm JC bolt
(2) 021555
1/4-20 JC nut
(2) long side panel
0112491 - 84" tables
0112542 - 60" tables
(4) 037779
5/16-18 x 1" glide
(2) 0104836
4" snap-in grommet
(1) 021263
3-1/4" round grommet
(1) 025069
glide wrench
(1) 025039
4mm hex wrench
(2) 0112492
short side panel
0112776R4 Page 1 of 9
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Spectrum Industries InVision 37102
Summary of Contents for Spectrum Industries InVision 37102
- Page 1 Assembly Instructions To purchase parts or accessories, please contact us at www.spectrumfurniture.com 1-800-235-1262 Thank you for purchasing Spectrum products! Before you begin, please make sure all parts and proper quanti- ties are included. Any parts damaged during shipment must be reported within 15 days of receipt.
- Page 2 1. Attach legs to worksurface Set the assembled worksurface face-down onto a flat non-abrasive surface like a carpeted floor close to the table’s final location. Set the legs onto the bottom of the worksurface as shown with the insert panels facing toward the center. Figure 1. Note the rear leg (with the grommet hole) will mount on the flat edge of the worksurface.
- Page 3 rear leg 2. Attach cord channel rails to legs (with grommet hole) Orient the upper cord channel rails with the inside rail flanges pointing up from the worksurface as shown. Figure 2A. Attach to the worksurface with 1/4-20 x 1/2” PHMS 1/4-20 x 1/2”...
- Page 4 3. Attach bottom panel Attach the bottom panel to the two lower rails with (8) 8-32 x 1/2” PH thread-cutting screws as shown. Figure 3. Note the end tabs will be pointing upward. Attach each end tab on the bottom panel to each leg with (2) 1/4-20 x 1/2” PHM screws. Tighten the leg screws from step 1C securely.
- Page 5 Optional - Attach equipment rack to cord channel Note: The following procedure shows how to attach an optional equipment equipment rack rack to the table while the table is still upside-down during the table assembly. Lower the equipment rack over the cord channel as shown. Note the hinge- side of each door will go toward the flat edge (or rear) of the table.
-
Page 6: Install Side Panels
4. Flip table upright CAUTION The table is heavy when assembled. Using 4-5 people, carefully tip the table up on Use caution when flipping upright. its side and over until upright. Figure 4. Figure 4 5. Install grommets Install (2) 4” snap-in grommets into the bottom panel. Figure 5. Install (1) 3-1/4”... - Page 7 Worksurface cutouts Note: Cutouts in the worksurface can be made by the customer after the table has been assembled, but are only recommended within the maximum cutout area shown in Figures 7A & 7B. Cutouts made beyond this shaded area could interfere with the legs, cord channel rails, or worksurface reinforcement bars.
- Page 8 Options Display Stand w/ Monitor Mount Camera Mount mount supports 37”-63” attaches to display stand monitors up to 200 lbs above or below monitor 37106 (1 mount included) 37108 WARNING The monitor should always be lifted off the stand before moving the table. 7-Outlet Power Strip, insured w/ surge protector, bracket, and 12’...
-
Page 9: Warranty
Warranty WE WILL MAKE IT RIGHT FOR YOU! Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available and each product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations). Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or concerns.
Need help?
Do you have a question about the InVision 37102 and is the answer not in the manual?
Questions and answers