Related Manuals for Batca LINK LD-1
Summary of Contents for Batca LINK LD-1
- Page 1 Revision 1 June 2011 LD-1 Chest Press/Pec Fly Owner’s Manual Serial Number Here Date of Purchase www.batcafitness.com LD-1 Owner’s Manual 1207 New Hope Road, Raleigh, NC - 919.255.1233 - www.batcafitness.com...
-
Page 2: Table Of Contents
Instructions Congratulations on the purchase of your new Batca LD-1. This gym will provide you with a lifetime of enjoyment to meet your strength training needs. Batca Fitness Systems strives to build the best quality gyms and to package these gyms in such a way to avoid any damage during shipping. -
Page 3: Parts Listing
Frame Components Accessories ITEM NO. PART NUMBER DESCRIPTION QTY. ITEM PART NUMBER DESCRIPTION QTY. BFM-51173 Magnetic Weight Stack Pin BFP-10824 LD-1 Cage Upholstery BFP-10823 Base Assembly BFP-10828 Upright Support ITEM PART NUMBER DESCRIPTION QTY. BFP-10829 Pec Top Assembly BFP-10839 Cable Lockout Plate BFP-52137 Head Pad BFP-51745... -
Page 4: Hardware Comparison
Bolt Length Note: Bolt length is measured from the underside of the head of the bolt. Batca Fitness Systems LD-1 Owner's Manual... - Page 5 www.batcafitness.com LD-1 Owner’s Manual...
- Page 6 Batca Fitness Systems LD-1 Owner's Manual...
- Page 7 www.batcafitness.com LD-1 Owner’s Manual...
-
Page 8: Main Assembly
LD-1 Cage BFP-10823 Base Assembly BFP-10828 Upright Support BFH-50174 4 1/2” Pulley BFP-51750 SHCS 3/8” x 2 3/4” BFP-51748 SHCS 3/8” x 3 1/4” BFP-51746 1/2” Pulley Spacer BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems LD-1 Owner's Manual... - Page 9 Step 2: Make sure all bolts are tightened before moving Figure 2 Item # Part # Description BFP-10829 Pec Top Assembly BFP-10839 Cable Lockout Plate BFP-10827 Guide Rod BFP-51745 Guide Rod Plate BFP-51719 Anti-Deflection Plate BFM-10413 Weight Stack Top Plate BFM-50632 Weight Stack Plate BFM-51173...
- Page 10 Pec Cam (Right) BFP-10833 Pec Cam (Left) BFP-10830 Upper Pec Arm (Right) BFP-10831 Upper Pec Arm (Left) All Flat Washers and Nylocks are 3/8” BFP-51738 Small Aluminum Cap unless otherwise noted. BFP-52373 BHSCS 3/8” x 3/4” Batca Fitness Systems LD-1 Owner's Manual...
- Page 11 Step 4: Figure 4 Item # Part # Description Right Lower Pec Arm BFP-10832R Left Lower Pec Arm BFP-10832L BFP-51736 Axle BFP-51756 SHCS 3/8” x 5 1/4” All Flat Washers and Nylocks are 3/8” BFH-50146 3/8” Flat Washer unless otherwise noted. BFH-50157 3/8”...
- Page 12 Step 5: Figure 5 Item # Part # Description BFP-10825 Foot Assist Assembly BFP-51699 Axle All Flat Washers and Nylocks are 3/8” unless BFP-51696 Small Aluminum End Cap otherwise noted. BFM-50620 BHSCS 3/8” x 1” Batca Fitness Systems LD-1 Owner's Manual...
- Page 13 Step 6: Figure 6 Item # Part # Description BFP-10826 Chest Press Arm BFP-10837 Chest Press Pulley Holder BFP-51750 SHCS 3/8” x 2 3/4” All Flat Washers and Nylocks are 3/8” unless BFP-51884 SHCS 3/8” x 4 1/4” otherwise noted. Anywhere a washer is against BFH-50146 3/8”...
- Page 14 Chrome Adjustment Tube BFH-50210 Gas Spring BFP-51759 SHCS 3/8” x 2 1/4” BFP-51750 SHCS 3/8” x 2 3/4” All Flat Washers and Nylocks are 3/8” unless otherwise noted. BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems LD-1 Owner's Manual...
-
Page 15: Cable Routing
Step 8: 1 3/8” Shoulder Bolt Figure 8 Item # Part # Description 60 1/4” CAB-15000 Weight Stack to Free Floater BFP-10838 Free Floater BFH-50174 4 1/2” Pulley BFH-50530 5” Pulley BFH-50351 1 3/8” Shoulder Bolt CAB-15000 BFP-51752 SHCS 3/8” x 2 1/4” BFH-50267 5/16”... - Page 16 4 1/2” Pulley CAB-15002 BFH-50351 1 3/8” Shoulder Bolt BFP-51752 SHCS 3/8” X 2 1/4” All Flat Washers and Nylocks are BFH-50267 5/16” Nylock 3/8” unless otherwise noted. BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems LD-1 Owner's Manual...
- Page 17 Step 10: Make Sure Cable is Routed EXACTLY like this diagram and underneath ALL bolts to prevent cable damage. If Cable wears due to being installed incorrectly it will void your warranty. Figure 10 Every place that a pulley is inside a tube there must be a pulley spacer in use instead of a flat washer.
- Page 18 Bottom Pad BFP-51653 SHCS 3/8” x 1 1/4” BFP-51799 SHCS 3/8” X 5” All Flat Washers and Nylocks are 3/8” unless BFH-50147 3/8” Lock Washer otherwise noted. BFH-50146 3/8” Flat Washer BFH-50204 3/8” Curved Washer Batca Fitness Systems LD-1 Owner's Manual...
- Page 19 Step 12: Figure 12 Do not tighten the four bolts on the shroud until next step. Item # Part # Description BFP-51711 Placard Plate BFP-51740 Rear Weight Stack Shroud BFH-50254 HCS 3/8” x 3/4” All Flat Washers and Nylocks are 3/8” unless otherwise noted.
- Page 20 Make sure all bolts are tightened Figure 13 Item # Part # Description BFP-51742 Front Weight Stack Shroud (Right) BFP-51741 Front Weight Stack Shroud (Left) All Flat Washers and Nylocks are 3/8” unless otherwise noted. Batca Fitness Systems LD-1 Owner's Manual...
-
Page 21: Final Assembly And Troubleshooting
Final Assembly and Troubleshooting Weight Stack Decals: 200lb Stack IMPORTANT - Check These Components Before Using Gym: Each Cable with a threaded bolt on either end must be threaded at least 1/2” into its attachment, whether it be a Free Floater, Lockout Free Floater, or the Top Plate of the weight stack. -
Page 22: Cable Tension And Adjustments
Note: If the top plate raises off of the second plate in the weight stack, then the cable ten- sion is too tight. You will need to take some of the tension out to lower the Top plate flush with the second plate. Batca Fitness Systems LD-1 Owner's Manual... -
Page 23: Maintenance
Preventive Maintenance Batca Fitness Systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below should be followed. -
Page 24: Warranty
Improper installation, improper assembly or follow-up maintenance along with installation of parts or accessories not originally intended for products of Batca Fitness Systems are also not covered by this warranty. Only genuine Batca parts should be used for replacement, repair, and maintenance for this warranty to apply. -
Page 25: Floor Plan Layout
Layout Diagram The LD-1 has a layout dimension of 3’-9” (width) x 5’-0” (length) x 5’-10” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. www.batcafitness.com LD-1 Owner’s Manual...