Page 1
Revision 1 June 2011 LD-2 Mid Row/Lat Pull Down Owner’s Manual Serial Number Here Date of Purchase www.batcafitness.com LD-2 Owner’s Manual 1207 New Hope Road, Raleigh, NC - 919.255.1233 - www.batcafitness.com...
Instructions Congratulations on the purchase of your new Batca LD-2. This gym will provide you with a lifetime of enjoyment to meet your strength training needs. Batca Fitness Systems strives to build the best quality gyms and to package these gyms in such a way to avoid any damage during shipping.
Page 8
WASHER. DO NOT TIGHTEN BOLTS UNTIL STEP 3 Figure 1 Item # Part # Description BFP-10842 LD-2 Cage BFP-10840 Base Assembly BFP-51747 SHCS 3/8” x 3” BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems LD-2 Owner's Manual...
Page 9
SHCS 3/8” x 5 1/4” otherwise noted. Anywhere a washer is against the round side of a tube there is to be a 3/8” CURVED BFH-50204 3/8” Curved Washer WASHER 3/8” FLAT WASHER. instead of a BFH-50157 3/8” Nylock www.batcafitness.com LD-2 Owner’s Manual...
Page 10
BFH-50204 3/8” Curved Washer 3/8” CURVED tube there is to be a WASHER 3/8” FLAT instead of a BFH-50146 3/8” Flat Washer WASHER. BFH-50157 3/8” Nylock Batca Fitness Systems LD-2 Owner's Manual...
Page 11
Step 4: Figure 4 Item # Part # Description BFP-10844 Mid Row Arm BFP-51784 Axle All Flat Washers and Nylocks are 3/8” BFP-51696 Small Aluminum End Cap unless otherwise noted. BFH-50620 BHSCS 3/8” x 1” www.batcafitness.com LD-2 Owner’s Manual...
Page 12
BFP-52371 SHCS 5/16” x 1/2” BFP-51752 SHCS 3/8” x 2 1/4” BFP-51750 SHCS 3/8” x 2 3/4” All Flat Washers and Nylocks are 3/8” BFH-50146 3/8” Flat Washer unless otherwise noted. BFH-50157 3/8” Nylock Batca Fitness Systems LD-2 Owner's Manual...
Page 13
BFP-51756 SHCS 3/8” x 5 1/4” washer is against the round side of a tube 3/8” CURVED WASHER there is to be a BFH-50204 3/8” Curved Washer 3/8” FLAT WASHER. instead of a BFH-50157 3/8” Nylock www.batcafitness.com LD-2 Owner’s Manual...
Page 14
Placard Plate BFH-50174 4 1/2” Pulley BFP-52373 BHSCS 3/8” x 3/4” BFP-51752 SHCS 3/8” x 2 1/4” All Flat Washers and Nylocks are 3/8” unless otherwise noted. BFH-50146 3/8” Flat Washer BFH-50157 3/8” Nylock Batca Fitness Systems LD-2 Owner's Manual...
Page 15
SHCS 3/8” x 2 3/4” BFH-50146 3/8” Flat Washer Large Ball CAB-15003 BFH-50157 3/8” Nylock BFH-50188 Snap Hook All Flat Washers and Nylocks are 3/8” unless otherwise noted. BFH-50351 1 3/8” Shoulder Bolt BFH_50267 5/16” Nylock www.batcafitness.com LD-2 Owner’s Manual...
Page 16
BHSCS 3/8” x 3/4” BFP-51653 SHCS 3/8” x 1 1/4” BFP-50147 3/8” Lock Washer All Flat Washers and Nylocks are 3/8” unless BFP-50146 3/8” Flat Washer otherwise noted. 2 Link 1” Chain 2xBFC-50128 BFH-50188 Snap Hook Batca Fitness Systems LD-2 Owner's Manual...
Page 17
Item # Part # Description BFP-51740 Rear Weight Stack Shroud BFP-52373 BHSCS 3/8” x 3/4” All Flat Washers and Nylocks are 3/8” unless BFH-50254 HCS 3/8” x 3/4” otherwise noted. BFH-50146 3/8” Flat Washer www.batcafitness.com LD-2 Owner’s Manual...
Page 18
Step 11: Make sure all bolts are tightened Figure 11 Item # Part # Description BFP-51741 Left Front Weight Stack Shroud BFP-51742 Right Front Weight Stack Shroud Batca Fitness Systems LD-2 Owner's Manual...
Guide Rod Clean guide rods with a lint-free cloth and apply a thin layer of silicone lubricant (Part # BFH- 50262) to each guide rod. This will ensure a glass smooth performance from your weight stack. www.batcafitness.com LD-2 Owner’s Manual...
Page 20
You will need to take some of the tension out to lower the Top plate flush with the second plate. Fine Adjustments to the cable can be made here. It is very important to tighten the jam nut after adjustments have been made Batca Fitness Systems LD-2 Owner's Manual...
Preventive Maintenance Batca Fitness Systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below should be followed.
Improper installation, improper assembly or follow-up maintenance along with installation of parts or accessories not originally intended for products of Batca Fitness Systems are also not covered by this warranty. Only genuine Batca parts should be used for replacement, repair, and maintenance for this warranty to apply.
Page 23
Layout Diagram The LD-2 has a layout dimension of 3’-8” (width) x 5’-1” (length) x 7’-0” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. www.batcafitness.com LD-2 Owner’s Manual...
Need help?
Do you have a question about the LD-2 and is the answer not in the manual?
Questions and answers