Related Manuals for LDARC AK103
Summary of Contents for LDARC AK103
- Page 1 AK103 AK123 PNP manual User manual and video please visit：WWW.LDARC.COM PRODUCT>>MULTROTOR>>AK SERIES>> AK103/AK123 PNP AK103/AK123 Caddx.US turtle PNP manual V2 manual 190826...
- Page 2 Note 2 Note 3 VTX antenna need fixed with glue When the center hole is to small, please use the M1.5 or M1.0 drill to ream the hole. Mounting screws M2*7 1.2*4 1.2*4 AK103 AK123 1.2*5 M2*4 M2*3 1.2*6 1.2*6 1.2*6...
- Page 3 Configuration Name AK103 AK123 Wheelbase 109mm 122mm Weight 65mm-2(1.0) 75mm Racer Prop XT11015-6100KV(1.0mm shaft) XT1103-6500KV(1.5mm shaft) Motor Camera RunCam Nano2 F411E12A(MATEKF411) 4in1 12A BLheli_S(G-H-30) 0/25/100/200mW 48CH IRC-Tramp Receiver AC2000 DUAL-CORE TRI-MODE(S-FHSS,D16 non-E,D16 EU-LBT) Battery 11.4V 300mAh 30C The weight not include battery,receiver and bumper...
- Page 4 LDA-F411E12A parameters <1> STM32F411 MCU,Operation at 100Mhz,firmware target MATEKF411. <2> MPU-6000 six-axis SPI sensor. <3> Low power version AT7456E,support Betaflight OSD. <4> BEC use MP9943 High-Efficiency Synchronous mode DC-DC, support 5V@1.5A output. <5> TX1 and RX1 pads,can support IRC-Tramp or Camera control. <6>...
- Page 5 Feature definition Firmware target : MATEKF411 + G-H-30 Voltage : 2S~4S ESC : 12A x 4way BEC : 5V@1.5A Current scale value : 210 IF USE 2S BATTERY PLEASE MAKE SURE VOLTAGE NOT LOWER THAN 2S-4S 6.8V WHEN ESC IN HEAVY LOAD ! KEY WILL BE DISABLED WHEN USER ENABLE IRC-TRAMP CLC FILTER...
- Page 6 Receiver Bind AC900(S-FHSS+D16) bind,transmitter(FRSKY X9D/Futaba T18SZ) Bind:Check receiver mode before bind,the first blink after power on indicate the setting, is S-FHSS, is D16 FUTABA S-FHSS BIND:Turn on the TX then power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key.
- Page 7 RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6) BIND:Power on the receiver while pressing the key,green LED fast blink meaning already in bind mode, user can release the key,then set your TX into bind mode.Green LED turn off and red LED solid mean bind finished, exit TX from bind mode,receiver’...
-
Page 8: Firmware Update
Firmware Update BETAFLIGHT firmware allready flash before leave the factory,user just need connect PC to adjust the parameter 1.Open betaflight configuration ,then click ,select FW version MATEKF411 4.0.5- MATEKF411 -01-08-2018-9 21:11(stable) 2.Click ,then click to download FW to FC, click after FW Connect updating finish into setting menu... - Page 9 4.Port，Open UART2 switch and save 5.Configuration，select ESC protocol“DSHOT600”，Set up the receiver protocol...
- Page 10 6.PID set 7.Mode set...
- Page 11 8.OSD set -10-...
- Page 12 Product and factory code Factory code Name AK103 NO RX PNP.AK103.NO RX PNP.AK123.NO RX AK123 NO RX AK103 AC2000 PNP.AK103.AC2000 AK123 AC2000 PNP.AK123.AC2000 AK103 KIT KIT.AK103 AK123 KIT KIT.AK123 XT11015-6100KV MOTOR.XT11015-6100KV XT1103-6500KV MOTOR.XT1103-6500KV PROP.65MM-2(1.0) 65mm-2(1.0) 75mm Racer PROP.75MM RACER(1.5MM HUB) BAT.11.4V 300MAH 30C...