Outdoor Cutoff Temperature; Offset; Minimum Water Temp; Maximum Water Temp - Raypak TempTracker mod+ Installation And Operation Instructions Manual

18 Raypak, Inc.

outdoor cutoff teMperature

----------- SETTINGS ------------
Adjustable Off, 20ºF - 100ºF, On
Season Winter
Set Point 140 F
Button: MENU/Set Point/Outdoor Cutoff
<System Settings>
Button: MENU/Set Point/Offset/Outdoor Cutoff
<Maintenance>
• If the outdoor sensor is installed, the Outdoor Cutoff screen will automatically appear after
<Histories>
<System Startup>
the temperature Set Point has been selected.
BACK SELECT
• When the outdoor temperature falls to the adjustable Outdoor Cutoff temperature, the
TempTracker mod+ will control and modulate Boilers to hold the calculated temperature.
• When the outdoor temperature rises to the Outdoor Cutoff plus a 2°F differential, the TempTracker mod+ will disable the system.
The Message Display Line will display Outdoor Cutoff.
• The Outdoor Cutoff can be set from 20°F to 100°F. In addition, the Setting can be set to ON or OFF. In the ON position, the
STARTUP
System Relay will run regardless of the Outdoor temperature (OD) and the burner stages will be active to hold the calculated water
temperature. (Note: The lowest water temperature the TempTracker mod+ will circulate is 70°F. If the Outdoor Cutoff is turned
-------- SYSTEM STARTUP ------
ON and the Season is set to Winter, the TempTracker mod+ will circulate at least 70°F water even in the hottest of weather.) In the
(START)
OFF position, the system pump will always be off and all burner stages will be off for heating.
to continue

offset

BACK
Adjustable 50ºF - (-50ºF)
Button: MENU/Set Point/Offset
------------- WARNING ------------
• The Offset setting lets you adjust the starting points of the Reset Ratio curves. This means
THESE SETTINGS
that, regardless of the Outdoor temperature (OD), or the Reset Ratio that has been selected,
CHANGE PRIMARY
when the Offset setting is changed, that change is directly added to or subtracted from the
SYSTEM FUNCTIONS.
calculated temperature. For example, if the Set Point temperature was 130°F and the Offset
BACK CONTINUE
was changed from 0° to 10° (an increase of 10°), then the Set Point temperature would
increase to 140°F
-------- ARE YOU SURE? -------
• The Offset setting does not change the ratio selection. For instance, with 1.00 (OD):1.00 (SYS) Reset Ratio, the System water
No
----------- SETTINGS ------------
Yes
temperature (SYS) will always increase one degree for each degree change in the Outdoor temperature (OD). What the Offset does
Season Winter
Set Point 140 F
is add or subtract a constant temperature value. (See Understanding Operation Concept on page 5)
BACK
• If required: Adjust the Water Offset in mild weather. If the ambient building temperatures are too warm in the mild weather, <System Settings>
<Maintenance>
decrease the Water Offset. If the ambient building temperatures are too cold in the mild weather, increase the Water Offset. The
<Histories>
<System Startup> rule of thumb for baseboard radiation is to change the Offset 4°F for every 1°F you wish to change the building temperatures. In
---------- SENSOR TYPE ---------
----------- SETTINGS ------------
BACK SELECT
radiant heat applications, change the Offset 1°F or 2°F for every 1°F you wish to change the building temperature.
Set Point F
Season Winter
Set Point C
Set Point 140 F
Reset F
<System Settings>

MInIMuM Water teMp

Reset C
<Maintenance>
Adjustable 70ºF - 180ºF
<Histories>
<System Startup>
BACK
STARTUP
Button: MENU/Set Point/Offset/Outdoor Cutoff/Minimum Water Temp
BACK SELECT
• The Minimum Water Temperature must be set to the boiler manufacturer's specification.
Set Point
-------- SYSTEM STARTUP ------
The TempTracker mod+ will calculate the Set Point based on the Outdoor temperature
(OD), the Reset Ratio, and the Offset value. The TempTracker mod+ will control all boilers
------ EMS INPUT MODE -------
(START)
Disable
modulation to hold either the Set Point temperature, or the Minimum Water Temperature,
to continue
Enable
whichever is higher.
STARTUP
• The Minimum Water Temperature must be at least 20°F lower than the Maximum
BACK
BACK
Temperature (See next setting).
-------- SYSTEM STARTUP ------
------------- WARNING ------------
(START)

MaxIMuM Water teMp

to continue
THESE SETTINGS
Adjustable 90ºF - 240ºF
CHANGE PRIMARY
SYSTEM FUNCTIONS.
BACK
Button: MENU/Set Point/Offset/..../Maximum Water Temperature
• This is the highest temperature heating water the TempTracker mod+ will circulate through BACK CONTINUE
------------- WARNING ------------
the heating system. It is available in Reset mode only.
------- DHW SETPOINT -------
-------- ARE YOU SURE? -------
• When using a radiation system, it should be set according to the tubing or floor
THESE SETTINGS
No
manufacturer's specification.
180
CHANGE PRIMARY
Yes
F
• The Maximum Temperature must be at least 20°F higher than the Minimum Temperature.
SYSTEM FUNCTIONS.
[
BACK
BACK CONTINUE
BACK
-------- ARE YOU SURE? -------
No
---------- SENSOR TYPE ---------
Yes
Set Point F
Set Point C
----- SETBACK/SHUTDOWN -----
Reset F
BACK
Shutdown/Disable
Reset C
Tstat/Enable
Set Point
<System Settings>
<Maintenance>
<Histories>
<System Startup>
BACK
-------- SYSTEM STARTUP ------
BACK
------------- WARNING ------------
THESE SETTINGS
CHANGE PRIMARY
SYSTEM FUNCTIONS.
BACK
START
-------- ARE YOU SURE? -------
No
Yes
BACK
---------- SENSOR TYPE ---------
Set Point
Set Point
Reset
Reset
SAVE
BACK
------ EMS INPUT MODE -------
Disable
Enable
BACK
SAVE
Enabled
START
SAVE
------- DHW SETPOINT -------
Disabled
[
BACK
START
----- SETBACK/SHUTDOWN -----
Shutdown/Disable
]
Tstat/Enable
SAVE
SAVE
Setback
BACK
SAVE
140 F
SELECT
------------- SEASON --------------
Default: 65ºF
Winter
Summer
in Set Point
STARTUP BACK
------------ SET POINT ----------
(START)
140
F
to continue
[
BACK
START
--------- RESET RATIO ----------
1.00 OD=4.00 Sys
1.00 OD=3.00 Sys
1.00 OD=2.00 Sys
1.00 OD=1.50 Sys
1.00 OD=1.25 Sys
CONTINUE
1.00 OD=1.00 Sys
1.25 OD=1.00 Sys
Default: 0ºF
1.50 OD=1.00 Sys
in Reset only
2.00 OD=1.00 Sys
3.00 OD=1.00 Sys
4.00 OD=1.00 Sys
BACK
SAVE
-------------- OFFSET -------------
F
+0
F
C
------------- SEASON --------------
[
F
Winter
C
Summer
BACK
BACK SAVE
HISTORIES
Set Point
------------ SET POINT ----------
------------- SEASON --------------
Reset Options
Winter
Summer
140
----- EMS 4ma SETPOINT----- F
[
BACK
Default: 120ºF
BACK
120
SAVE F
in Reset only
[
------------ SET POINT ----------
BACK
--------- RESET RATIO ----------
1.00 OD=4.00 Sys
140
F
1.00 OD=3.00 Sys
[
1.00 OD=2.00 Sys
------ EMS 20ma SETPOINT-----
1.00 OD=1.50 Sys
BACK
1.00 OD=1.25 Sys
220
1.00 OD=1.00 Sys
F
1.25 OD=1.00 Sys
--------- RESET RATIO ----------
[
1.50 OD=1.00 Sys
1.00 OD=4.00 Sys
BACK
2.00 OD=1.00 Sys
1.00 OD=3.00 Sys
180
3.00 OD=1.00 Sys
1.00 OD=2.00 Sys
F
4.00 OD=1.00 Sys
1.00 OD=1.50 Sys
]
Default: 240ºF
BACK 1.00 OD=1.25 Sys
SAVE
1.00 OD=1.00 Sys
in Reset only
1.25 OD=1.00 Sys
1.50 OD=1.00 Sys
-------------- OFFSET -------------
----- PROVE/DHW SHARING ----
2.00 OD=1.00 Sys
Prove
3.00 OD=1.00 Sys
DHW Priority
+0
4.00 OD=1.00 Sys
F
DHW No Priority
[ BACK
No Priority (Summer)
BACK
BACK
-------------- OFFSET -------------
SAVE
HISTORIES
+0
F
Setback Input
[ Reset Options
BACK
---------- BOOST MODE ---------
----- EMS 4ma SETPOINT-----
30 Minutes
Disabled
Summer
BACK
------------ SET POINT ----------
------- OUTDOOR CUTOFF -------
[
BACK
in Reset
[
SAVE
BACK
--------- RESET RATIO ----------
1.00 OD=4.00 Sys
1.00 OD=3.00 Sys
1.00 OD=2.00 Sys
1.00 OD=1.50 Sys
]
--- MINIMUM WATER TEMP ----
1.00 OD=1.25 Sys
SAVE
1.00 OD=1.00 Sys
1.25 OD=1.00 Sys
1.50 OD=1.00 Sys
[
2.00 OD=1.00 Sys
BACK 3.00 OD=1.00 Sys
4.00 OD=1.00 Sys
BACK
--- MAXIMUM WATER TEMP ----
-------------- OFFSET -------------
[
BACK
[
BACK
SAVE
--- SYS= 91 F, 10:57Am ---
HISTORIES
Reset Options
------- OUTDOOR CUTOFF -------
BACK
]
----- EMS 4ma SETPOINT-----
SAVE
--- OD= 54 F, 11:36Am ---
[
SAVE
[
BACK
BACK
------- OUTDOOR CUTOFF -------
Enabled
BACK
------ EMS 20ma SETPOINT-----
]
--- MINIMUM WATER TEMP ----
[
SAVE
------- OUTPUT A TYPE --------
SAVE
BACK
4-20ma
[
] Disabled
0-10v
[ BACK
0-5v
SAVE
2-10v
BACK
1-5v
]
--- MINIMUM WATER TEMP ----
BACK
--- MAXIMUM WATER TEMP ----
SAVE
------- OUTPUT D TYPE --------
----- PROVE/DHW SHARING ----
[
]
4-20ma
Prove
[
BACK
0-10v
SAVE
DHW Priority
0-5v
BACK
DHW No Priority
2-10v
No Priority (Summer)
--- MAXIMUM WATER TEMP ----
1-5v
SAVE
BACK
BACK --- SYS= 91 F, 10:57Am ---
[
------ MODULATION MODE ------
Normal
BACK
Parallel
---------- BOOST MODE --------- BACK
SAVE ]
BACK
--- SYS= 91 F, 10:57Am ---
30 Minutes
SAVE
Disabled
SAVE --- OD= 54 F, 11:36Am ---
BACK
BACK
]
SAVE
--------- SENSOR FAULT --------
BACK
--- OD= 54 F, 11:36Am ---
All Off
All On
------- OUTPUT A TYPE --------
SAVE
140
F
]
65
F
SAVE
]
SAVE
Reset Ratio
140
F
]
SAVE
SAVE
220
F
]
+0
F
SAVE
]
SAVE
NEXT
65
F
120
F
]
]
SAVE
SAVE
Reset Ratio
EXIT
65
F
]
220
SAVE
F
140 ]
F
SAVE ]
Reset Ratio
SAVE
SAVE
140
F
220
]
F
]
SAVE
SAVE
SAVE
SAVE
220
F
]
SAVE
Setback Input
NEXT
SAVE
SAVE
NEXT
EXIT
[
-
[
-
[
-
4
0
0
2
1
-
4
0
0
2
1
-
N
P