Table of Contents
Advertisement
14
Raypak, Inc.
startup settInGs
----------- SETTINGS ------------
Season
Winter
Set Point
proGraM cHanGe settInGs
<System Settings>
<Maintenance>
To be able to change the TempTracker mod+ settings the Program/Run Switch must be set to
<Histories>
Program. The switch is located under the Enclosure Wiring Cover for security. The Enclosure
<System Startup>
----------- SETTINGS ------------
Wiring Cover can be securely closed using a lock.
BACK
SELECT
Season
Winter
Set Point
140 F
startup seQuence
<System Settings>
Button: MENU/<System Startup>
<Maintenance>
• When powered, the TempTracker mod+ performs a self diagnostics-test on its components.
<Histories>
• On the first power up, the System Startup screen will appear after the initialization is
<System Startup>
STARTUP
BACK
complete. If it doesn't, the TempTracker mod+ has already been configured.
SELECT
• The System Startup menu sets the main parameters like the type of sensor, the type of
-------- SYSTEM STARTUP ------
output, and the modulating mode.
(START)
to continue
sensor type
STARTUP
Set Point °F, Set Point °C, Reset °F, Reset °C
BACK
Button: MENU/<System Startup>/..../Sensor type
-------- SYSTEM STARTUP ------
• Reset mode is only available if an outdoor sensor is connected to terminals 25 and 26. DO
------------- WARNING ------------
NOT select Reset without an outdoor sensor.
(START)
• The same Raypak temperature sensor can display either in °F or °C.
to continue
THESE SETTINGS
CHANGE PRIMARY
• If °F is selected, all temperatures and settings will be displayed in degrees Fahrenheit and
SYSTEM FUNCTIONS.
BACK
the TempTracker mod+ will operate as a Set Point Control in degrees Fahrenheit.
BACK
CONTINUE
• If °C is selected, all temperatures and settings will be displayed in degrees Celsius and the
------------- WARNING ------------
TempTracker mod+ will operate as a Set Point Control in degrees Celsius.
-------- ARE YOU SURE? -------
• Set point mode does not require an outdoor sensor. If an outdoor sensor is connected in Set
THESE SETTINGS
No
CHANGE PRIMARY
Point mode it will be used only as an outdoor cutoff point. That is, to turn the boilers and
Yes
SYSTEM FUNCTIONS.
system pump off.
BACK
BACK
CONTINUE
eMs Input Mode
-------- ARE YOU SURE? -------
(AvAilAble in Set point only)
No
---------- SENSOR TYPE ---------
Disable, Enable
Yes
Set Point
F
Set Point
C
Button: MENU/<System Startup>/..../EMS Input Mode
BACK
Reset
F
• This allows the TempTracker mod+ to receive an external set point from an BMS system.
Reset
C
• You must select the 4mA (min) and 20 mA (max) Set Points in the following screen.
• The 4mA can be set to any temperature between 70ºF to 200ºF.
BACK
---------- SENSOR TYPE ---------
• The 20mA can be set to any temperature between 90ºF to 240ºF. However, the 20mA
Set Point
F
Set Point
minimum setting must be 20ºF higher than the 4mA setting.
Set Point
C
• Connect the 4-20mA EMS Control Interface to the TempTracker mod+ RS485 connection.
Reset
F
Reset
C
------ EMS INPUT MODE -------
Disable
selectInG tHe output type
Enable
4-20mA, 0-5V, 0-10V, 1-5V, or 2-10V Outputs
BACK
Button: MENU/<System Startup>/..../Output A type/Output B type
Set Point
BACK
• Outputs can be configured for 4-20mA operation (current) or the voltage range can be
selected (0-5V, 0-10V, 1-5V, 2-10V).
------ EMS INPUT MODE -------
• Check the modulating motor to determine its control requirements.
Disable
• Select the appropriate Output Type for each of the Boilers. The TempTracker mod+ can
Enable
have a different Output type for each Boiler.
BACK
ModulatInG Mode
Normal, Parallel
------- DHW SETPOINT -------
Button: MENU/<System Startup>/..../Modulating Mode
• Some modulating boilers perform better as their modulation increases. For these units, it is
180
F
[
advantageous to run one unit at high modulation than several units at lower modulation. If
BACK
the units used are of this type, select Normal. This is the recommended setting for typical
------- DHW SETPOINT -------
180
F
[
----- SETBACK/SHUTDOWN -----
BACK
Shutdown/Disable
Tstat/Enable
Setback
A good practice after performing any Startup menu modifications is to
-------- SYSTEM STARTUP ------
140 F
check all operating settings and adjustments to match the new settings.
BACK
------------- WARNING ------------
THESE SETTINGS
CHANGE PRIMARY
SYSTEM FUNCTIONS.
BACK
-------- ARE YOU SURE? -------
No
Yes
START
BACK
---------- SENSOR TYPE ---------
Set Point
Set Point
START
Reset
Reset
BACK
SAVE
------ EMS INPUT MODE -------
Disable
Enable
BACK
SAVE
SAVE
Enabled
------- DHW SETPOINT -------
SAVE
[
SAVE
BACK
Disabled
Enabled
SAVE
----- SETBACK/SHUTDOWN -----
Disabled
Shutdown/Disable
Tstat/Enable
Setback
BACK
]
SAVE
]
SAVE
CLASS 1 WIRE ONLY.
STARTUP
ENCLOSED
ENERGY
MANAGEMENT
------------- SEASON --------------
EQUIPMENT
LISTED
Winter
99RA
Summer
(START)
BACK
to continue
------------- SEASON --------------
START
------------ SET POINT ----------
Winter
Summer
140
F
[
BACK
BACK
------------ SET POINT ----------
CONTINUE
--------- RESET RATIO ----------
1.00 OD=4.00 Sys
140
F
1.00 OD=3.00 Sys
[
1.00 OD=2.00 Sys
BACK
1.00 OD=1.50 Sys
1.00 OD=1.25 Sys
Default: Set Point ◦F
1.00 OD=1.00 Sys
SAVE
--------- RESET RATIO ----------
1.25 OD=1.00 Sys
1.00 OD=4.00 Sys
1.50 OD=1.00 Sys
1.00 OD=3.00 Sys
2.00 OD=1.00 Sys
1.00 OD=2.00 Sys
3.00 OD=1.00 Sys
1.00 OD=1.50 Sys
4.00 OD=1.00 Sys
F
1.00 OD=1.25 Sys
BACK
C
1.00 OD=1.00 Sys
F
1.25 OD=1.00 Sys
C
1.50 OD=1.00 Sys
-------------- OFFSET -------------
2.00 OD=1.00 Sys
3.00 OD=1.00 Sys
SAVE
+0
4.00 OD=1.00 Sys
F
Set Point
BACK
[
BACK
-------------- OFFSET -------------
HISTORIES
+0
F
Default: Disable
SAVE
[
Reset Options
BACK
----- EMS 4ma SETPOINT-----
HISTORIES
120
F
[
Reset Options
BACK
----- EMS 4ma SETPOINT-----
------ EMS 20ma SETPOINT-----
120
180
Default: 4-20mA
F
F
[
]
220
F
BACK
SAVE
[
BACK
------ EMS 20ma SETPOINT-----
220
F
[
BACK
----- PROVE/DHW SHARING ----
Default: Normal
Prove
DHW Priority
SAVE
DHW No Priority
No Priority (Summer)
BACK
----- PROVE/DHW SHARING ----
Prove
DHW Priority
DHW No Priority
Setback Input
No Priority (Summer)
---------- BOOST MODE ---------
BACK
30 Minutes
Disabled
-------- SYSTEM STARTUP ------
[
BACK
alert
------- OUTDOOR CUTOFF -------
CAUTION
: RISK OF ELECTRIC SHOCK
BACK
--------- RESET RATIO ----------
More than one disconnect switch may be required
to de-energize the equipment before servicing.
1.00 OD=4.00 Sys
1.00 OD=3.00 Sys
------------- WARNING ------------
1.00 OD=2.00 Sys
[
SAVE
1.00 OD=1.50 Sys
THESE SETTINGS
BACK
1.00 OD=1.25 Sys
CHANGE PRIMARY
1.00 OD=1.00 Sys
------- OUTDOOR CUTOFF -------
SYSTEM FUNCTIONS.
1.25 OD=1.00 Sys
1.50 OD=1.00 Sys
BACK
----------- SETTINGS ------------
2.00 OD=1.00 Sys
Season
3.00 OD=1.00 Sys
]
[
--- MINIMUM WATER TEMP ----
SAVE
Set Point
-------- ARE YOU SURE? -------
4.00 OD=1.00 Sys
SAVE
<System Settings>
BACK
No
BACK
<Maintenance>
Yes
<Histories>
[
<System Startup>
BACK
-------------- OFFSET -------------
BACK
BACK
]
--- MINIMUM WATER TEMP ----
SAVE
--- MAXIMUM WATER TEMP ----
---------- SENSOR TYPE ---------
[
Set Point
BACK
Set Point
[
Reset
BACK
[
Reset
HISTORIES
BACK
-------- SYSTEM STARTUP ------
BACK
--- MAXIMUM WATER TEMP ----
Reset Options
SAVE
--- SYS= 91 F, 10:57Am ---
----- EMS 4ma SETPOINT-----
[
------ EMS INPUT MODE -------
BACK
Disable
BACK
Enable
[
------------- WARNING ------------
SAVE
BACK
]
BACK
BACK
--- SYS= 91 F, 10:57Am ---
THESE SETTINGS
SAVE
Enabled
CHANGE PRIMARY
--- OD= 54 F, 11:36Am ---
SYSTEM FUNCTIONS.
------ EMS 20ma SETPOINT-----
BACK
BACK
]
[
-------- ARE YOU SURE? -------
Disabled
SAVE
No
BACK
BACK
--- OD= 54 F, 11:36Am ---
Yes
------- DHW SETPOINT -------
BACK
------- OUTPUT A TYPE --------
4-20ma
]
0-10v
[
0-5v
SAVE
BACK
---------- SENSOR TYPE ---------
2-10v
----- PROVE/DHW SHARING ----
BACK
Set Point
1-5v
Prove
Set Point
BACK
DHW Priority
Reset
------- OUTPUT A TYPE --------
DHW No Priority
4-20ma
Reset
No Priority (Summer)
]
0-10v
------- OUTPUT D TYPE --------
0-5v
SAVE
BACK
----- SETBACK/SHUTDOWN -----
]
BACK
4-20ma
2-10v
Shutdown/Disable
0-10v
SAVE
1-5v
Tstat/Enable
0-5v
BACK
Setback
2-10v
1-5v
BACK
------ EMS INPUT MODE -------
BACK
Disable
------- OUTPUT D TYPE --------
---------- BOOST MODE ---------
Enable
]
4-20ma
30 Minutes
0-10v
------ MODULATION MODE ------
Disabled
SAVE
BACK
0-5v
Normal
2-10v
Parallel
BACK
1-5v
BACK
BACK
SAVE
------ MODULATION MODE ------
Normal
Parallel
------- DHW SETPOINT -------
BACK
--------- SENSOR FAULT --------
SAVE
All Off
[
All On
C
140
D
F
]
(START)
SAVE
to continue
START
65
F
]
SAVE
PROGRAM
RUN
Reset Ratio
CONTINUE
65
F
Winter
]
140 F
SAVE
SAVE
140
F
]
Reset Ratio
SAVE
SAVE
SELECT
+0
F
]
140
F
F
SAVE
C
220
]
F
STARTUP
F
SAVE
]
C
SAVE
SAVE
(START)
Set Point
to continue
220
F
]
START
SAVE
120
F
]
NEXT
SAVE
SAVE
CONTINUE
220
F
NEXT
]
SAVE
EXIT
SAVE
180
F
]
SAVE
EXIT
F
C
SAVE
F
C
SAVE
SAVE
Set Point
SAVE
SAVE
Setback Input
SAVE
SAVE
SAVE
SAVE
SAVE
SAVE
180
F
]
E
D
E
D
Advertisement
Table of Contents
