Specifications - Sharp PN-80TH5 Operation Manual

nProduct Specifications
Model
LCD component
Max. resolution
Max. colors
Pixel pitch
Brightness (typical)
Contrast ratio (typical)
Viewing angle
Screen active area
Computer input signal
Sync signal
Plug and play
Power management
Input terminals
Output terminals
LAN terminal
Speaker output (internal/external)
Touch Panel
Touch pen
Expansion slot
Power requirement
Operating temperature *
Operating humidity *
Power consumption
(Input signal waiting mode *
Dimensions (excluding protrusions)
Weight
*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the
equipment, it is not possible to precisely maintain a constant level of brightness.
*2 D-sub input terminal only.
*3 When using this monitor laying flat on a surface (when the monitor is tilted more than 20 degrees upward from the perpendicular in relation
to a level surface), use this monitor at the ambient temperature between 41°F (5°C) and 86°F (30°C).
Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
* This monitor should not be mounted flat or used as a touch table type installation. Please consult an authorized SHARP dealer before
considering any type of flat installation (when the monitor is tilted more than 20 degrees upward from the perpendicular in relation to a level
surface), and find out about the mandatory flat mounting instructions.
*4 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satisfied.
*5 When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF.
*6 When POWER SAVE MODE is set to ON. When POWER SAVE MODE is set to OFF: 1.0 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
66
E

Specifications

(pixels) 3840 x 2160
inch (mm) 70-1/8 (W) x 39-7/16 (H) (1781.76 x 1002.24)
Video
Audio
Serial (RS-232C)
Video
Audio
Detection method
Computer connector
Touch pen adapter port
3 * 4
4
/standby mode * )
5 6
inch (mm) Approx. 73-3/8 (W) x 3-7/8 (D) x 42-15/16 (H) (1863 x 98 x 1090)
lbs. (kg) Approx. 160.9 (73)
PN-80TH5
80" Class [80-1/2 inch (204.4cm) diagonal] TFT LCD
Approx. 1.06 billion colors
0.464 mm (H) × 0.464 mm (V)
2 1
300 cd/m *
4000: 1
176° right/left/up/down (contrast ratio ≥ 10)
Analog RGB (0.7 Vp-p) [75 Ω], DisplayPort 1.2a
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*
Composite sync (TTL: positive/negative)*
VESA DDC2B
VESA DPMS
HDMI x 3
Mini D-sub 15 pin, 3 rows x 1
DisplayPort x 2
3.5 mm mini stereo jack x 1
3.5 mm mini stereo jack x 1
DisplayPort x 1
3.5 mm mini stereo jack x 1
10 BASE-T/100 BASE-TX
10 W + 10 W/10 W + 10 W 6 Ω
Capacitive type
USB (2.0 compliant) (Type B) x 2
Wireless communication method
(2.4GHz, Bluetooth Low Energy, FHSS method)
USB (2.0 compliant) (Type A)
13 V, 2.4 A
(power supplied when expanding the functions with an optional part)
AC 100 V - 240 V, 3.7 A, 50/60 Hz
41°F to 95°F (5°C to 35°C)
20% to 80% (no condensation)
325 W (7.0 W / 0.5 W)
2
2
,