Sharp PN-80TH5 Operation Manual page 51

Function
AUDIO SPEAKER SELECT
OPTION
AUDIO OUTPUT
AUDIO INPUT LEVEL
MONAURAL AUDIO
TOUCH INPUT BOTTOM USB
(Long side)
SELECT
SIDE USB (Short side)
START INPUT MODE
COMMUNICATION RS-232C/LAN
SETTING SELECT
BAUD RATE
Crestron Connected
REMOTE No.
MONITOR menu
Function
PORTRAIT/LANDSCAPE INSTALL
HORIZONTAL INSTALLATION
OSD H-POSITION
OSD V-POSITION
OPERATION MODE
POWER SAVE MODE
OFF IF NO OPERATION
TIME
POWER ON DELAY
INTERVAL
SELF ADJUST
START TIMING
TOUCH OUTPUT TOUCH OUTPUT
INVALID DISP. INVALID ICON
CHANGE DISPLAY
POSITION
TOUCH OPERATION MODE
TOUCH PANEL MODE
PALM CANCEL MODE
* This monitor should not be mounted flat or used as a touch table type installation. Please consult an authorized SHARP dealer before considering any type of flat installation (when the monitor
is tilted more than 20 degrees upward from the perpendicular in relation to a level surface), and find out about the mandatory flat mounting instructions.
Controlling the Monitor with a computer (RS-232C)
Command Direction Parameter
SPSL WR 0-1
AOUT WR 0-2
AIVP WR 0-1
MONO WR 0-1
0-6, 8
USCB WR
USCS WR 0-6, 8
SUIM WR 1-5, 7, 10-11
0-1
CTLS WR
BAUD WR 0-2
0-1
CRCN WR
RCNO WR 0-9
Command Direction Parameter
STDR WR 0-1
MLAY WR 0-1
OSDH WR 0-100
OSDV WR 0-100
FNCM WR 0-1
STBM WR 0-1
ATOF WR 0-1
AOFT WR 1-12
PODS WR 0-1
PWOD WR 1-60
AADJ WR 0-1
AADD WR 10-200
TOPI WR 0-1
TOIP WR 0-3
TOMD WR 0-1, 3
GMDP WR 0-1
PARE WR 0-1
Reply Control/Response contents
0-1 0: Internal speaker, 1: External speaker
0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2
0-1 0: 1.0Vrms, 1: 0.5Vrms
0-1 0: OFF, 1: ON
0-6, 8 0: INVALID, 1: BOTTOM INPUT TERM. (Long side), 2: DisplayPort1, 3: HDMI1,
4: HDMI2, 5: HDMI3, 6: D-SUB, 8:DisplayPort2
0-6, 8 0: INVALID, 1: SIDE INPUT TERM. (Short side), 2: DisplayPort1, 3: HDMI1,
4: HDMI2, 5: HDMI3, 6: D-SUB, 8:DisplayPort2
1-5, 7, 10-11 1: LAST INPUT MODE, 2: DisplayPort1, 3: HDMI1, 4: HDMI2, 5: HDMI3,
7: D-SUB, 10:OPTION (valid when you have used the expansion slot to expand
the functions), 11:DisplayPort2
0-1 0: RS-232C, 1: LAN
0-2 0: 9600bps, 1: 19200bps, 2: 38400bps
0-1 0: OFF, 1: ON
0-9 Sets the number of the remote control unit.
Reply Control/Response contents
0-1 0: LANDSCAPE, 1: PORTRAIT
0-1 0: OFF, 1: FACE UP*
0-100
0-100
0-1 0: MODE1, 1: MODE2
0-1 0: OFF, 1: ON
0-1 0: OFF, 1: ON
1-12 1-12: 1-12 hours
0-1 0: OFF, 1: ON
1-60 1-60: 1-60 seconds
0-1 0: OFF, 1: ON
10-200 10: 1 second through 200: 20 seconds
0-1 0: OFF, 1: ON
0-3 0: UPPER RIGHT, 1: UPPER LEFT, 2: LOWER RIGHT, 3: LOWER LEFT
0-1, 3 0: AUTO, 1: MULTI-TOUCH MODE, 3: SINGLE-TOUCH MODE
"ERR" when the touch panel is not connected.
0-1 0: OFF, 1: ON (When the input mode is HDMI, D-SUB[RGB], DisplayPort,
OPTION)
0-1 0: OFF, 1: ON
*
○
●
○
*
○
-
○
51
E