Subscribe to Our Youtube Channel
Related Manuals for Modena Casella Series
Summary of Contents for Modena Casella Series
- Page 1 User Manual Book (Electric Storage Water Heater) Casella Series ES 10D, ES 15D, ES 30D ES 10DR, ES 15DR, ES 30DR Snella Series ES 20SR...
-
Page 2: Introduction
Thank you for your trust in choosing MODENA products for your household needs. With your satisfaction as our priority, we constantly aim to deliver stylishly designed products equipped with state-of-the-art technology to assist you in your daily activities. This is your guidebook containing everything you need to know about our product. -
Page 3: Table Of Contents
CONTENTS PAGE. • Introduction • Part 1 : Important Safety Information • Part 2 : Product Introduction • Part 3 : Installation • Part 4 : How to Use • Part 5 : Maintenance • Part 6 : Troubleshooting • Part 7 : Disposal of Used Product •... -
Page 4: Part 1: Important Safety Information
Special Cautions Warning: If the supply cord is damaged, it must be replaced by MODENA technicians, MODENA service agent or similarly qualified persons in order to avoid a hazard. ... -
Page 5: Part 2: Product Introduction
During the heating process, there may be drops of water dripping from the pressure relief hole. This is a normal case. If there is an over-leaking, please contact MODENA customer call center for repair. This pressure relief hole shall, under no circumstances, be blocked; otherwise, the heater may be damaged, even resulting on accidents. - Page 6 Technical Performance Parameters Picture 4 Brief Introduction of Product Structure...
- Page 7 Picture 5 (Note: All dimensions are in mm) Internal Wiring Diagram...
-
Page 8: Part 3: Installation
Picture 6 Part 3: Installation Installation Instruction This electric storage water heater shall be installed on a solid wall. If the strength of the wall cannot bear the load equal to two times of the total weight of the heater filled fully with water, it is then necessary to install a special support. - Page 9 The height of the supply socket from the ground should not be less than 1.8m (see Picture 8). If there is a problem on the power cord, it should be replaced by MODENA agencies or qualified person who is able to do the repairment so as to ensure the safety.
- Page 10 Picture 10 Note: Please be sure to use the accessories provided by MODENA to install this electric storage water heater. This electric storage water heater cannot be hung on the bracket until it has been confirmed to be firm and reliable. Otherwise, this water heater may drop off from the wall, resulting to its damage, even serious accidents of injury to the user.
-
Page 11: Part 4: How To Use
Part 4: How to Use Operating Procedure Check all the piping connection to avoid the leakage case before turning on this electric storage water heater. Open one of the outlet valves of the water heater, then, open the inlet valve .to get the water heater filled with water. - Page 12 Rotate the knob according to the marking on the knob to increase or decrease the setting temperature. The Red “Power” LED and Green “Heating” LED remain ON while there is power to the system. The Green LED will turns off when the water temperature reaches the user setting, at the end of the heating phase.
- Page 13 Long pressing “-” button will render the setting temperature to decrease at the rate of 5 C /s. If no button is pressed within 5s, the system will store the setting temperature parameters and exit the temperature setting status. (4) “BOOK” (Heating Time Programming) Button When the appliance is in the power-on state: press this button to enter into the booked time setting mode for the heating program.
- Page 14 Notes: 1. The delay booking cannot set the minutes of the booked time; 2. In the setting process of booked time, the set time shall flicker. In the flickering period: a. Do not press any button within 5s and then confirms the booking state; b.
- Page 15 Picture 15 Specific Functions of Button and Display Screen of ES XXDR Series (1) “ON/OFF” Button This key acts as an ON/OFF operating key. When this appliance (the water heater) is connected to the power, the display screen is fully bright for 2s. If the power to the memory function is disconnected (there is power outage), this appliance will return to the working condition before the power outage.
- Page 16 (5) “BOOK” (HEATING TIME PROGRAMMING) Button When the appliance is in the power-on state: press this button on the remote controller to enter into the booked time setting mode for the heating program. At this moment, the booked time can be set through pressing “+”or “-”...
- Page 17 Picture 16 Notes: 1. The delay booking can’t set the minutes of the booked time; 2. In the setting process of booked time, the set time shall flicker. In the flickering period a. No button is pressed within 5s and then confirms the booking state; b.
- Page 18 Factory Setting Function When in the power off state, if the “MODE” button and the “POWER” button are pressed for 3s simultaneously, the display screen will be fully bright and the system will enter into the factory setting mode (buzzer will ring, if any). Then, the system will enter to the “heating/heat preservation”...
- Page 19 D. ES 20SR Picture 17 Note: • The temperature displayed on the LED refers to water temperature of the central part in the tank. The outlet water temperature may be higher than the displayed temperature. • The hot water from the water heater may cause scald. Please test the temperature of the hot water before using.
- Page 20 rate of 5 C/s. If no button is pressed within 5s, the system will store the setting temperature parameters and exit the temperature setting status. (4) “BOOK” (HEATING TIME PROGRAMMING) Button When the appliance is in the power-on state: press this button to enter into the booked time setting mode for the heating program.
-
Page 21: Part 5: Maintenance
When in non-heating state, if the water temperature in water heater is less than or equal to 6°C, connect to the corresponding heating tube to conduct heating; The water heater could stop heating when the temperature reaches 10°C (heating is not displayed, i.e., hidden heating). ... - Page 22 Picture 18 Warning: Non-professionals are not allowed to disassemble the thermal switch to do the reset. Please contact professionals of MODENA to maintain this electric storage water heater. Otherwise, MODENA will not take responsibility of any accidents. Tank Cleaning...
-
Page 23: Part 6 : Troubleshooting
If the water contains limestone (Mud), the heating element cannot function properly (slow heat) because it was covered by a crust of limestone (mud). Therefore, heating element must be cleaned off from the sediment each year. To do this cleaning procedure, contact MODENA Call Center. -
Page 24: Part 7: Disposal Of Used Product
Part 7: Disposal of Used Product This symbol (crossed-out wheeled dustbin) on the product or in its packaging indicates that this product must not be treated as household waste. Instead, it should be taken to the appropriate waste collection point for the recycling of electrical and electronic equipment. - Page 25 Power 800 W, 1200 W 350 W, 600W 200 W Water Pressure 0.75 Ma Water Pipe Diameter 0.5 Inch Temperature Max 75 Product Dimension 455 x 455 x 388 mm 400 x 400 x 312 mm 355 x 355 x 295 mm Product Weight 13.75 kg 10.50 kg...
- Page 26 11/20...
Need help?
Do you have a question about the Casella Series and is the answer not in the manual?
Questions and answers