Johnson Controls Frick PowerPac Installation Operation & Maintenance page 19

Page 2
Setpoint
High
Prop. Band ________ ________
Dead Band ________ ________
Cycle Time ____ Sec _____ Sec Warning Delay ___ Sec Cycle Time
VFD Prop Band ________ ________
VFD Integ. Time ____ Sec _____ Sec Shutdown Delay ___ Sec VFD Integ. Time ____Sec ____ Sec
Channel ________________________
Auto Cycle
Start ________
Start Delay ____ Min
Stop ________
Stop Delay ____ Min
High Discharge Temperature
Load Inhibit _______
Force Unload _______
Warning _______
Warning Delay _______ Sec
Shutdown _______
Shutdown Delay _______ Sec
High Discharge Pressure
Regulation Modes 1 & 3 Modes 2 & 4
Load Inhibit _____ PSIG
Force Unload _____ PSIG
Warning _____ PSIG
Warning Delay _____ Sec
Shutdown _____ PSIG
Shutdown Delay _____ Sec
Maximum Discharge Pressure ______________ PSIG
Highest Cap. To Permit Start ______________ %
Start Period Before Cap. Increase ______________
Stopping Period For Cap. Unload ______________
Compressor Auto Mode Min. Cap. ______________ %
Capacity Unload Assist. ______________ Rate __________%
Separator Velocity Ref. ______________
Compression Ratio ______________
Liquid Slug Warning ______________
Liquid Slug Shutdown ______________
Low Compressor Oil Temperature
Warning __________ Delay _____ Sec
Shutdown __________ Delay ______ Sec
High Compressor Oil Temperature
Warning ______ Delay _______ Sec
Shutdown ______ Delay _______ Sec
Low Compressor Oil Pressure
Warning ________ PSI Delay ________ Sec
Shutdown ________ PSI Delay ________ Sec
High Filter Pressure
Warning ________ PSI Delay ________ Min
Shutdown ________ PSI Delay ________ Min
Main Oil Injection _______________________
Shutdown ________ PSI Delay ________ Sec
Oil Heater Off Above ________
High Level Shutdown Delay ________ Sec
Low Oil Level Delay ________ Sec
Oil Pump Lube Time Before Starting ________ Sec
Dual Pump Transition Time ________ Sec
FRICK
Unit Serial # _____________________________ Frick Order No: ____________________________
Capacity Control Setpoints
Regulation Safeties
Load Inhibit ___
Low
Force Unload ________
Warning __________
Shutdown _________
Low Suction
Load Inhibit __________
Force Unload __________
Warning __________
Warning Delay ______ Sec
Shutdown __________
Shutdown Delay ______ Sec
Compressor Safeties
Start Differential
Pressure Below
50 PSI
Dual Mode _______________
_____ PSIG
_____ PSIG
_____ PSIG
_____ Sec
_____ PSIG
_____ Sec
Package Safeties
POWERPAC
® ™
FORMS
Setpoint
High
Prop. Band _______ ________
Dead Band _______ ________
____Sec ____ Sec
VFD Prop Band _______ ________
Channel _________________________
Auto Cycle
Start _________
Start Delay _____ Min
Stop _________
Stop Delay _____ Min
Warning Delay _______ Sec
Shutdown Delay _______ Sec
Economizer ________________
Fixed Pressure Setpoint _________________
Balance Piston
Ignore Delay ____ Min
Fail Delay ____ Min
Oil Log _______________ Delay ______ Sec.
Main Oil Injection On When Discharge Temperature
Is Above __________ °F for _____ Sec
Pull Down ______________________
Capacity Position ________ %
Amount of Time _________ Sec
Pump Down ____________________
On When Suction Above ____ PSIG Delay _____ Min
DX Circuit
#1 Action _______________________
Off When Below _______ %
On When Above _______ %
#2 Action ______________________
Off When Below _________ %
On When Above _________ %
Liquid Injection _________________
On When Above __________ Delay _______ Sec
Dual Port Transition ________
Hot Gas Bypass _________ %
Power Assist _________ Sec
170.600-IOM (JUN 11)
Regulation Safeties
Load Inhibit ____
Low
Force Unload _________
Warning ___________
Warning Delay ____ Sec
Shutdown __________
Shutdown Delay ____ Sec
Low Suction
Load Inhibit
Force Unload
Warning
Warning Delay
Shutdown
Shutdown Delay
High Suction Pressure
Load Inhibit _______ PSIG
Force Unload _______ PSIG
Warning _______ PSIG
Shutdown _______ PSIG
On When Above _______%
Off When Below _______%
Override Discharge Pressure ________
Port Value ________
Pressure Input _________________
On ____ %
Off ____ %
Page 19
__________
__________
__________
______ Sec
__________
______ Sec