Overview - Grundfos Control MPC 2000 Series Installation And Operating Instructions Manual

8.2 Overview

Section Display and display number
8.4 Status (1)
8.4.1 8.4.1 Actual alarms (3.1)
8.4.2 8.4.2 System (1.2)
8.4.3 8.4.3 Operating mode (1.2.1)
8.4.4 8.4.4 Setpoint (1.2.2)
8.4.5 8.4.5 Setpoint influence (1.2.3)
8.4.6 8.4.6 Measured values (1.2.4)
8.4.7 8.4.7 Analog inputs (1.2.5)
8.4.8 8.4.8 Log graph (1.2.6)
8.4.9 Battery status (1.2.7)
8.4.10 8.4.10 Pump 1-6, Pilot pump (1.3 - 1.10)
8.5 Operation (2)
8.5.1 8.5.1 Operation (2)
8.5.2 8.5.2 System operating mode (2.1.1)
8.5.3 8.5.3 Control mode (2.1.2)
8.5.4 8.5.4 Alternative setpoints (2.1.3)
8.5.5 8.5.5 Individual pump control (2.1.4)
8.5.6 8.5.6 Pump 1-6 (2.1.4.1 - 2.1.4.6)
8.5.7 8.5.7 Operation, pilot pump (2.1.4.7)
8.6 Alarm (3)
8.6.1 8.6.1 Alarm status (3)
8.6.2 8.6.2 Actual alarms (3.1)
8.6.3 8.6.3 Alarm log (3.2)
8.6.4 8.6.4 Service contact information (3.3)
8.7 Settings (4)
8.7.1 8.7.1 Primary controller (4.1)
8.7.2 8.7.2 PI controller (4.1.1)
8.7.3 8.7.3 Alternative setpoints (4.1.2)
8.7.4 8.7.4 Alternative setpoints 2-7 (4.1.2.1 - 4.1.2.7)
8.7.5 8.7.5 External setpoint influence (4.1.3)
8.7.6 8.7.6 Setting of influence function (4.1.3.2)
8.7.7 8.7.7 Primary sensor (4.1.4)
8.7.8 8.7.8 Secondary sensor (4.1.5)
8.7.9 8.7.9 Clock program (4.1.6)
8.7.10 8.7.10 Proportional pressure (4.1.7)
8.7.11 8.7.11 S-system configuration (4.1.8)
8.7.12 8.7.12 Setpoint ramp (4.1.9)
8.7.13 8.7.13 Pump cascade control (4.2)
8.7.14 8.7.14 Min. time between start/stop (4.2.1)
8.7.15 8.7.15 Max. number of starts/hour (4.2.1)
8.7.16 8.7.16 Standby pumps (4.2.3)
8.7.17 8.7.17 Forced pump changeover (4.2.4)
8.7.18 8.7.18 Pump test run (4.2.5)
8.7.19 8.7.19 Pump stop attempt (4.2.7)
8.7.20 8.7.20 Pump start and stop speed (4.2.8)
8.7.21 8.7.21 Min. performance (4.2.9)
8.7.22 8.7.22 Compensation for pump start-up time (4.2.10)
8.7.23 8.7.23 Secondary functions (4.3)
8.7.24 8.7.24 Stop function (4.3.1)
8.7.25 8.7.25 Pilot pump
8.7.26 8.7.26 Soft pressure build-up (4.3.3)
8.7.27 8.7.27 Emergency run (4.3.5)
8.7.28 8.7.28 Digital inputs (4.3.7)
8.7.29 8.7.29 Functions of digital inputs (4.3.7.1)
8.7.30 8.7.30 Analog inputs (4.3.8)
8.7.31 8.7.31 Analog inputs (4.3.8.1 - 4.3.8.7)
(4.3.2)*
Page
19
20
20
20
21
21
21
21
22
22
22
23
23
23
24
26
26
27
27
28
28
29
29
29
30
30
31
32
32
33
34
34
35
35
36
37
37
38
38
38
39
39
40
40
41
41
42
42
43
45
46
47
47
48
48
49
17