Table Of Fp3/Fp5 System Registers - Panasonic FP3 Technical Manual

6-3. Table of FP3/FP5 System Registers

Number Description
Memory Allocation
0 Sequence program memory size
(See note 1. on the next page)
1 Machine language program memory size
(See note 1. on the next page)
2 Comment memory size
3 Unused
4 Unused
Internal I/O Setting
5 Counter start No. setting(See note 2.)
6 Timer/Counter hold area start No. setting
(See note 2. on the next page)
7 Internal relay hold area start No. setting
(See note 3. on the next page)
8 Data register hold area start NO. setting
(See note 3. on the next page)
9 File register hold area start No. setting
(See note 3. on the next page)
10 Link relay hold area setting for Link 0
(See note 3. on the next page)
11 Link relay hold area setting for Link 1
(See note 3. on the next page)
12 Link register hold area setting for Link 0
(See note 3. on the next page)
13 Link register hold area setting for Link 1
(See note 3. on the next page)
14 Step ladder hold/non-hold setting
15 Data output hold/non-hold setting
16 to 19 Unused
RUN Mode During an Error
20 Duplicate output
21 Output unit fuse blow
22 Advanced unit error
23 I/O verification error
24 Watchdog timer time out
(This register No. is only used by the FP5)
25 Unused
26 Operation error
27 Remote I/O slave link error
28 I/O error in the Remote I/O slave station
29 Unused
Wait Time Setting
30 Watchdog timer's time out value
(This register no. is only by the used FP5)
31 Time setting for managing multiple frames
32 Data transfer's wait times setting for
F145(SEND), P145(PSEND)/
F146(RECV), P146(PRECV) instructions,
F152(RMRD), P152(PRMRD)/
F153(RMWT), P153(PRMWT) instructions
(See note 4)
33 Assigned time for a program
block-edition-in-RUN

6-3. Table of FP3/FP5 System Registers

Default value Settable range
8 FP3: 2 to 10k words
FP3(16k type)&FP5: 2 to 16 words
0 FP3: 0 to 8k words
FP3(16k type)&FP5: 0 to 14k words
3 Use default value "3".
– –
– –
200 0 to 256
200 0 to 256
60 0 to 98
0 0 to 2,04
0 0 to 22,525
0 0 to 64
64 64 to 128
0 0 to 128
128 128 to 256
1(Non-hold) 0:Hold, 1:Non-hold
0(Non-hold) 0:Non-hold, 1:Hold
– –
0(Disabled) 0:Output disable
1:Output enable
0(Stop) 0:Stop
0(Stop) 1:Continue
0(Stop)
0(Stop) 0:Stop 1:Continue
Refer to system register No.30
0(Stop) 0:Stop
0(Stop) 1:Continue
0(Stop)
– –
120(300 ms) 4 to 256(10ms to 640ms)
2,600(6.5s) 4 to 32,760(10ms to 81.9s)
800(2.0s) 4 to 32,760(10ms to 81.9s)
5,000(10ms) 1,000 to 65,535
(2,000 to 131,070 µs)
81