Table Of Contents - Raytheon Anschütz STD 22 Compact GYRO COMPASS Installation And Service Manual

Table of Contents

Table Of Contents3
Safety Notes11
General Information13
Can Bus (Can = Controller Area Network)23
Preparing To Install The Std 22 Compact Gyro Compass25
Std 22 Compact Compass – Scope Of Supply25
General Information Concerning Installation Of The Std 22 Compact Compass26
Creating Cable Connections27
General Information Concerning On-Board Wiring27
Requirements For Stripping The Connecting Cable27
Creating The Cable Connection28
Example Of A Proper Cable Connection29
General Information About Creating An Earth Connection30
Creating An Earth Connection30
Installing The Compass And Putting It Into Operation31
Principle Of Dismantling The Enclosure Door31
Remove The Transportation Support With Outer Sphere, Supporting Liquid And Distilled Water31
Assembling The Compass Enclosure32
Installation Of The Compass Enclosure32
Horizontal Alignment For Installation Of The Compass Enclosure34
Installation Of The Gyrosphere35
Outer Sphere35
Filling With Distilled Water And Supporting Liquid37
Filling With Liquids37
Measuring Cone For Supporting Liquid Level38
Inserting The Outer Sphere In The Compass Enclosure39
Principle Of Inserting The Outer Sphere In The Compass Enclosure39
Creating Cable Connections And Plug Connections41
Overview of Plug Connections and Fuses on Pcb's41
Arrangement of Pcb's in the STD 22 Compact Compass41
Arrangement Of Plugs, Terminal Boards And Fuses42
Connecting The Course Receiver In The Std 22 Compact Gyro Compass43
Course Receiver Connections43
Connection For Status And Control Signals45
Connecting Signal Inputs For Qs And Sec In The Std 22 Compact Gyro Compass47
Connection Of Signal Inputs For Qs And Sec48
Connecting The Power Supply Cable49
Connection Of The +24Vdc Power Supply49
Connecting The Compass To Earth50
Installation And Commissioning Of Optional Features51
Connecting The Power Supply51
Additional Output Box 146--103 (Device Open)51
Installation And Commissioning Of The Additional Output Box 143--10351
Making A Signal Connection52
Connection Of Course Bus In The Std 22 Compact Gyro Compass52
Installation And Commissioning Of The Ac/Dc Converter53
Ac/Dc Converter (Terminal Board)54
Operator Unit Quick--Settling (Front View)56
Installation And Commissioning Of The Operator Unit Quick Settling (Qs) 130--60656
Installing The Operator Unit Quick- -Settling57
Operator Unit Quick Settling (Rear View)57
Switching On, Settling And Adjustment59
Switching On The Compass59
Checks On The Compass59
Measuring The Compass Power Supply Voltage59
Checking The Dip Switch Settings On The Compass60
Checks On The Compass Before Setting Into Operation60
Setting The Std 22 Compact Compass Into Operation61
Indications On The Compass During The Heating Stage61
Indications On The Compass During The Settling Stage62
Setting The Compass Zero (Reference Course)63
Dip Switch B37 And Buttons B38/B3963
Procedure For Setting The Compass Zero64
Reading The Alignment Error65
Table At Compass Cover (Inner Side)65
Setting Channel 1 And Channel 266
Setting The Information Source For Speed Error Correction69
Adjustment Of Essential Operating Modes73
Function Check On Externally Connected Course Receivers80
Dip Switch B37 And Button B38/B3980
Checking Connected Course Receivers (Course Data)81
Preparing To Install The Std 22 Gyro Compass83
Std 22 Compass – Scope Of Supply83
General Information Concerning Installation Of The Std 22 Compass84
Overview Of Plug Connections And Fuses On Pcb's99
Creating A Cable Connection From Std 22 Compass → Distribution Unit101
Connecting To The Power Supply (Distribution Unit)102
Connecting The Can Bus Plug103
Can Bus Plug103
Setting The Jumpers For The Can Bus104
Switches B32 And B31 For Can1 And Can2 Termination Resistors105
Switching The Termination Resistors For The Can Bus (E10 Only)105
Setting The Can Bus Address114
Adjustments Of Essential Operating Modes115
Function Check Of Rot122
Fuses, Jumper, Led's, Buttons and Plugs125
Dip Switch Settings127
Switch B 37 (Dip Switch)127
Overview Of Functions Of All Dip Switch Settings128
Adjustments Of Parameters (In Ascending Order Of Function)132
Adjustments Of Parameters (In Ascending Order Of Their Appearance)134
7 Segment Displays And Their Meaning136
Functional Description Of Dip Switch Settings (For General Use)137
Setting Compass Zero138
Set The Speed Source For Sec150
Functional Description Of Dip Switch Settings (Sec)173
Tasks To Be Performed Regularly193
Changing The Supporting Liquid And Distilled Water193
Removing The Outer Sphere From The Compass Enclosure193
Dismantling The Outer Sphere194
Draining The Supporting Liquid And Distilled Water195
Dismantled Outer Sphere (Overhead View)195
Measuring Cone (Top View)196
Error Messages198
"Error Message" in Digital Display198
Warnings200
Warning 1 "Fan Failure"201
Warning 2 "Heater Failure"202
Warning 3 "Supporting Liquid > 60°C"202
Supporting Liquid Level Too Low203
Voltage Cut-Off203
Nmea 0183 Format Gll204
Nmea 0183 Format Rot205
Nmea 0183 Format Hdt205
Nmea 0183 Format Vhw206