Table of Contents
Advertisement
Operator Cab
G. ENGINE WARNING
The Engine Warning Indicator will be displayed when there is
an engine fault. Refer to the Operation section on Warning
Indicators and Fault Codes and the Engine Indicator Chart.
H. HIGH HYDRAULIC OIL TEMPERATURE
The hydraulic oil temperature indicator illuminates when the
oil temperature is above 1800 F. If the hydraulic oil temperature
indicator illuminates, stop and idle the engine to allow time
for cooling. If the hydraulic oil temperature indicator does
not go out after five (5) minutes, stop the Telehandler, follow
proper shut down procedures, tag the Telehandler with "Do
Not Operate" tags, and have a qualified mechanic service or
repair the Telehandler BEFORE placing it into service again.
I. WATER IN FUEL
The Water in Fuel Indicator will be displayed when water is
detected in the fuel filter. Drain the water by opening the
petcock on the bottom of the fuel filter.
J. DATE DISPLAY
K. TIME OF DAY DISPLAY
L. FUEL GAUGE
Indicates the approximate quantity of fuel available in the
tank. The total capacity of the fuel tank is 17 gallons.
M. BOOM ANGLE INDICATOR
Use the boom angle indicator to determine the boom angle
when referring to load capacity charts.
N. SWAY ANGLE INDICATOR
Digitally displays the angle at which the Telehandler frame is
swayed (left or right). A quick indicator is the red marker rep-
resenting the horizon (a horizontal position).
O. TACHOMETER
Indicates engine rotation speed (rpm) on a digital readout.
P. ENGINE COOLANT TEMPERATURE GAUGE
Indicates the temperature of the coolant in the engine cool-
ing system. After starting the Telehandler, allow time for the
temperature indicator to begin moving before operating the
Telehandler. After the engine has sufficiently been warmed
up, normal engine coolant temperature should read between
1800 to 2000 F.
Q. VOLTAGE GAUGE
Indicates the amount of charge in Volts. The normal system
voltage is between 12.5 and 14 Volts. If the voltage gauge
shows abnormal readings, stop the Telehandler, follow proper
shut down procedures, tag Telehandler with "Do Not Operate"
tags, and have a qualified mechanic service or repair the
Telehandler BEFORE placing it into service again.
R. TERRAIN SELECT BUTTON
Used with the auger attachment, it allows to select the type of
soil and to control the engine rpm with the joystick while the
machine is in NEUTRAL. Available options are:
•
Manual
•
Hard Soil
•
Sandy Soil
NOTE:
"Hard Soil" and "Sandy Soil" options disable the
accelerator pedal. "Manual" option allows for controlling the
engine rpm with the joystick AND with the accelerator pedal.
NOTE: While in any gear, the joystick can no longer be used
to control the engine speed (rpm).
S. HOUR METER
Indicates and records engine operating hours. Use the hour
meter to establish a Telehandler maintenance schedule.
T. ENGINE LOAD
Displays the percent of rated load for the current engine RPM
that is being applied to the engine.
U. MENU SELECTOR
Allows access to the MENU options.
V. SETTINGS MENU
Enables access to the Settings Menu.
W. ENGINE
Allows access to the ENGINE MAINTENANCE options.
Touching this icon opens a new screen depicting the
scheduled preventive maintenance mandated by the engine
manufacturer.
X. DAY/NIGHT DISPLAY MODE
This option dims the screen brightness to accommodate the
night Telehandler operation.
Y. HYDRAULIC OIL PRESSURE INDICATOR / WARNING
The Oil Pressure Indicator will turn yellow when the oil pressure
is below normal (between 20 and 10 psi). It turns red under
10 psi. If the Oil Pressure Indicator comes on during normal
operation, stop the Telehandler, follow proper shut down
procedures, tag Telehandler with "Do Not Operate" tags, and
have a qualified mechanic service or repair the Telehandler
BEFORE placing it into service again.
35
XR630
Operation Manual
Advertisement
Table of Contents
