Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pilz PSEN 2.1b-26
Summary of Contents for Pilz PSEN 2.1b-26
- Page 1 PSEN 2.1b-26 PSEN sensor technology Operating Manual-21380-EN-12...
- Page 2 Preface This document is the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.
-
Page 3: Table Of Contents
Adjustment ..........................ATEX installation and operating regulations (X) ..............Periodic test ........................... Dimensions in mm ......................... Technical details ........................Safety characteristic data ......................Order reference ........................System ............................Accessories ..........................EC declaration of conformity ....................Operating Manual PSEN 2.1b-26 21380-EN-12... -
Page 4: Introduction
PSEN 2.1b-26 Introduction Validity of documentation This documentation is valid for the product PSEN 2.1b-26, ATEX. It is valid until new docu- mentation is published. This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. -
Page 5: Safety
If installed in other environments, measures should be taken to comply with the applicable standards and directives for the respective installation site with regard to in- terference. Operating Manual PSEN 2.1b-26 21380-EN-12... -
Page 6: Safety Regulations
Disposal In safety-related applications, please comply with the mission time T in the safety-related characteristic data. When decommissioning, please comply with local regulations regarding the disposal of electronic devices (e.g. Electrical and Electronic Equipment Act). Operating Manual PSEN 2.1b-26 21380-EN-12... -
Page 7: For Your Safety
Operation Magnetic Switching voltage 24 VDC Series connection via PSEN i1 interface ECOLAB tested Function description If the actuator is within the response range (safety gate closed), the safety contacts of the safety switch are closed. Operating Manual PSEN 2.1b-26 21380-EN-12... -
Page 8: Block Diagram
PSEN 2.1b-26 The safety switch is designed for applications in series connections. Operate the PSEN 2.1b-26, ATEX in conjunction with the following components: Actuator PSEN 2.1-20 (see Order reference [ 19]), Interface PSEN i1 (see Order reference) and a connected evaluation device (see... -
Page 9: Lateral And Vertical Offset
Make sure that the safety switch cable extends from the EX area into the non-Ex area and that the cable connection is within the non-Ex area. Protect the safety switch's electrical connections from corrosion. The safety contacts are not short circuit-proof. Operating Manual PSEN 2.1b-26 21380-EN-12... -
Page 10: Pin Assignment
[3+] black Requirements and connection to evaluation devices For use of PSEN 2.1b-26, ATEX in accordance with DIN EN 60947-5-3 an evaluation device must be connected. Connect the PSEN 2.1b-26, ATEX either with a certified Pilz evaluation device or with an evaluation device with defined properties... - Page 11 Technical details [ of PSEN 2.1b-26, ATEX – Always comply with the max. switching current safety contacts of PSEN 2.1b-26, ATEX. Outputs at the evaluation device must only be switched on again when both reed con- tacts at the safety switch have been opened and closed (partial operation lock)
- Page 12 11 12 21 22 31 32 41 Non-Ex area 11 12 21 22 33 34 43 44 Ex area PSENmag Fig.: Dual-channel connection of four PSENmag to the input circuits of an evaluation device Operating Manual PSEN 2.1b-26 | 12 21380-EN-12...
-
Page 13: Installation
PSEN 2.1b-26 Examples for connection to Pilz evaluation devices: PSEN i1 PNOZmulti PSENmag brown white blue black Non-Ex area Ex area Legend I0 Input OSSD I1 Input OSSD T1, T2 Test pulse outputs PSEN i1 PNOZ s3 PSENmag brown white... - Page 14 Do not apply any installation tools (e.g. Pliers) on the surfaces of the switch. Install safety switch and actuator – facing each other in parallel – so that the faces with the product names are opposite each other. Operating Manual PSEN 2.1b-26 | 14 21380-EN-12...
-
Page 15: Adjustment
– Protect the edges of the safety switch base from shock. This can be achieved by full face installation, for example (see Installation ex- ample). – Please also refer to the additional information in the Installation [ section. Operating Manual PSEN 2.1b-26 | 15 21380-EN-12... -
Page 16: Periodic Test
NOTICE The safety function should be checked after initial commissioning and each time the plant/machine is changed. The safety functions may only be checked by qualified personnel. Dimensions in mm Safety switch Actuator Operating Manual PSEN 2.1b-26 | 16 21380-EN-12... -
Page 17: Technical Details
Vibration EN 60947-5-2 In accordance with the standard Frequency 10 - 55 Hz 1 mm Amplitude Shock stress In accordance with the standard EN 60947-5-2 Acceleration Duration 11 ms Airgap creepage Pollution degree Operating Manual PSEN 2.1b-26 | 17 21380-EN-12... -
Page 18: Safety Characteristic Data
You must comply with the safety characteristic data in order to achieve the required safety level for your plant/machine. Operating mode B10d in accordance with EN ISO TM [year] in accordance with EN 13849-1: 2015 and EN 62061 ISO 13849-1:2015 Sensor, 2-channel 2.000.000 Operating Manual PSEN 2.1b-26 | 18 21380-EN-12... -
Page 19: Order Reference
Magnetic safety switch, Cable, 10 m 502 250 PSEN2.1-20/8mm/10m/ actuator round, with as- EX/1unit sured operating distance 8 mm PSEN 2.1b-26 1switch ATEX Magnetic safety switch Cable, 10 m 522 150 PSEN 2.1-20/1actuator Actuator round, with as- 512 120 sured operating distance... - Page 20 PSEN 2.1b-26 The complete EC Declaration of Conformity is available on the Internet at www.pilz.com/ downloads. Representative: Norbert Fröhlich, Pilz GmbH & Co. KG, Felix-Wankel-Str. 2, 73760 Ost- fildern, Germany Operating Manual PSEN 2.1b-26 | 20 21380-EN-12...
- Page 21 Back cover Support Technical support is available from Pilz round the clock. Americas Australia Scandinavia +45 74436332 Brazil +61 3 95600621 +55 11 97569-2804 Spain Canada Europe +34 938497433 +1 888-315-PILZ (315-7459) Austria Switzerland Mexico +43 1 7986263-0 +41 62 88979-30...