Troubleshooting - DCS RDT-305 Use And Care Manual

TROUbLESHOOTING

proBLEM
NoN FUNCTIoNAl
oNE oR MoRE BURNERs
WIll NoT lIGHT
INCoRRECT FlAME
sooTY BURNER FlAME
proBLEM
No ovEN lIGHT
No ovEN HEAT (BAkE)
No ovEN BRoIl
UNEvEN BAkING
No CoNvECTIoN
CoNvECTIoN NoIsY
proBLEM
NoN FUNCTIoNAl
loW HEAT
32
rAnGEs & CookTops
possiBLE CAUsE
No ElECTRICITY oR
GAs sUPPlY
TECHNICAl
No ElECTRICITY
No GAs
WRoNG GAs
dIRTY BURNERs
BURNERs MIs-AlIGNEd
WATER IN BURNER(s)
dIRTY ElECTRodE
TECHNICAl
Too lARGE oR sMAll
MIs-AlIGNEd BURNER AssY
rAnGE oVEns
possiBLE CAUsE
No ElECTRICITY
loosE BUlB
BURNEd oUT BUlB
No ElECTRICITY (CHECk ovEN lIGHT)
IMPRoPER sETTINGs
TECHNICAl
IMPRoPER sETTINGs (sEE No BAkE)
TECHNICAl
INsUFFICIENT PRE-HEAT TIME
IMPRoPER sETTINGs
IMPRoPER UTENsIls/PlACEMENT
TECHNICAl
No CoNvECTIoN PAN
TECHNICAl
rAnGE GriDDLE & GriLL
possiBLE CAUsE
No ElECTRICITY oR GAs sUPPlY
RAdIANT TRAY IMPRoPERlY INsTAllEd
TECHNICAl
PlUGGEd BURNER PoRTs
soLUTion
TURN oN GAs sUPPlY vAlvE
CHECk CIRCUIT BREAkERs
CAll AUTHoRIZEd sERvICE
CHECk CIRCUIT BREAkERs
CHECk GAs sUPPlY AT WAll
vERIFY GAs TYPE (sEE PAGE 33 FoR
loCATIoN oF
ClEAN BURNERs
AlIGN & REAssEMBlE BURNERs
dIs-AssEMBlE & dRY BURNER(s)
ClEAN BURNER ElECTRodE
CAll AUTHoRIZEd sERvICE
vERIFY GAs TYPE (sEE lABEl oN BACk)
REAlIGN ANd RE-AssEMBlE BURNER AssY (PAGE26)
soLUTion
CHECk CIRCUIT BREAkERs
CHECk PlUG AT WAll (RdT,RGT & RGTC)
BE sURE BUlB Is sECURE IN soCkET
REPlACE BUlB
CHECk CIRCUIT BREAkERs
CHECk PlUG AT WAll oUTlET
vERIFY PRoPER sETTINGs oN kNoB & sElECToR
BUTToNs (IF APPlICABlE)
CAll AUTHoRIZEd sERvICE
vERIFY PRoPER sETTINGs
CAll AUTHoRIZEd sERvICE
AlloW ovEN To PREHEAT BEFoRE BAkING
vERIFY PRoPER sETTINGs oN kNoB & sElECToR
BUTToNs (IF APPlICABlE)
UsE PRoPER UTENsIls & PlACE THEM PRoPERlY (sEE
UsE & CARE)
CAll AUTHoRIZEd sERvICE
CHECk FoR AIR MovEMENT
CAll AUTHoRIZEd sERvICE
soLUTion
TURN oN GAs sUPPlY vAlvE
CHECk CIRCUIT BREAkERs
RE-INsTAll RAdIANT TRAY CoRRECTlY
CAll AUTHoRIZEd sERvICE
sEE PAGE 26 FoR BURNER ClEANING PRoCEdURE
lABEl