Related Manuals for DCS CS-364G
Summary of Contents for DCS CS-364G
-
Page 1: Installation Guide
CS COOKTOP SERIES Installation Guide MODELS: CS-366 CS-364GL CS-486GL CS-364G CS-486GD CS-484GG CS-485GD... - Page 2 A MESSAGE TO OUR CUSTOMERS Thank you for selecting this DCS CS Cooktop. Because of this appliance’s unique features we have developed this Installation Guide. It contains valuable information on how to properly install your new appliance for years of safe and enjoyable cooking.
-
Page 3: Table Of Contents
CS Cooktop 36” / 48”Wiring Schematic ........ -
Page 4: Introduction
INTRODUCTION The DCS Professional CS Cooktops feature a large number of features varying with each model . All models feature a minimum of 4 surface burners, with the option of up to 6 surface burners on all models. All of the 48" and 36" Cooktops feature the possibility of various grill and griddle combinations. -
Page 5: Models
MODELS 48” CS COOKTOP MODELS CS-484GG CS-486GL CS-486GD CS-485GD 36” CS COOKTOP MODELS RGS-366 RGS-364GL RGS-364GD... -
Page 6: Planning The Installation
C) Cooktop 1) Locate cooktop according to cooktop installation instructions. 2) Measure distance from counter surface to top of trim on cooktop adding 1/8” for backguard clearance. 3) Transfer this measurement to the wall. This will mark the bottom of your backguard. -
Page 7: Unpacking And Handling
The center screw is for shipping and should be removed. Due to the weight of the cooktop, along with a built-in side frame gasket that is meant to rest and create a seal on the counter top once installed, it is not necessary to anchor the unit to the counter. -
Page 8: Ventilation Requirements
For best smoke elimination, the lower edge of the hood should be installed a minimum of 30" to a maximum of 36" above the cooktop cooking surface, (step 3 pg. 8). If the hood contains any combustible materials (i.e. a wood covering) it must be a minimum of 36" above the cooking surface. -
Page 9: Cabinet Preparation
4) The cooktop can be installed in various positions with the front either flush or projecting, depending on the countertop depth. See Fig. 2 & Fig. 4 (cooktop side view). 5) Establish the centerline of the desired cooktop location. It should be the same as the center of the overhead ventilation hood. - Page 10 CABINET PREPARATION STEP 3: (CONTINUED) 6) Cut the openings for the following installation: Standard counter top installation, see Fig. 5A Deep counter or island installation, see Fig. 5B NOTE: If the deck is used, the sides or bottom of the cutout may be solid combustible or non-combustible material.
-
Page 11: Cabinet Preparation
Countertop Level Countertop level 8 7/16" 8 7/16” 1/2" 1/2” 3”To Center Line 3" To Center Line of Gas Inlet of Gas Inlet 1/2" 1/2” Cabinet face for installation Cabinet face for installation with projecting control panel with projecting control panel Cabinet face for installation Cabinet face for installation with flush control panel... -
Page 12: Backguard Installation
See also page 5. The backguard must be installed when there is less than a 12" clearance between combustibles and the back of the cooktop (above the cooking surface, see Fig. 5, page10). Wall Mount Full Backguard (Model #’s BGS-3030,... -
Page 13: Electrical / Gas Connections
The third prong should not, under ANY circumstances, be cut or removed. GAS REQUIREMENTS Verify the type of gas supplied to the location. The cooktop are shipped from the factory set up and adjusted for natural gas or LP (propane), depending on specific model ordered. The unit cannot be converted. -
Page 14: Hook-Up To Gas Supply
1/2 psig (3.5kPa.). When checking the manifold gas pressure, the inlet pressure to the regulator should be at least 7.0” W.C. for natural gas or 12.0” for LP. Flex Line To Cooktop Flex Line to Cooktop Manual Shut-Off... -
Page 15: Test And Adjustments
STEP 7: CAUTION: For warranty coverage, DCS requires that burner adjustments be made by a qualified technician at the time of installation. Extreme care should be used when adjustments are made after installation. Improper or lack of adjustments will void your warranty. -
Page 16: Installer Final Checklist
GAS SUPPLY Connection: 1/2 NPT with a minimum 5/8" diameter metal flex line. Site gas supply is compatible with cooktop model, & sufficient pressure is available (see gas requirements pg. 12). Manual gas shut-off valve installed in an accessible location. -
Page 17: Wiring Diagrams / Schematics
CS 36” / 48” WIRING DIAGRAM... -
Page 18: Cs Cooktop 36" / 48"Wiring Schematic
CS 36” / 48” SCHEMATIC... -
Page 19: Cs Cooktop 485 Wiring Diagram
CS 485 WIRING DIAGRAM... -
Page 20: Cs Cooktop 485 Wiring Schematic
CS 485 WIRING SCHEMATIC... -
Page 21: How To Obtain Service
For warranty service, contact DCS Customer Service at (888) 281-5698. Before you call, please have the following information ready: Model Number Serial Number Date of installation A brief description of the problem Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your... -
Page 22: Warranty
DCS to be defective. Replacement will be F.O.B. DCS, and DCS will not be liable for any transportation costs, labor costs, or export duties. This warranty shall not apply, nor can we assume responsibility for damage that might... - Page 23 NOTES...
- Page 24 NOTES...
- Page 25 NOTES...
- Page 26 5800 Skylab Road, Huntington Beach, CA 92647 Tel: 714.372.7000 • Fax: 714.372.7001 Customer Service: (888) 281-5698 www.dcsappliances.com As product improvement is an ongoing process at DCS, we reserve the right to change specifications or design without notice. P/N 17526 Rev. B...