Danfoss VLT AQUA Drive FC 202 Operating Manual page 66

Specifications
High/normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure IP20
Enclosure IP21/IP54
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V)[A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V)
[kVA]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V) [A]
8 8
Maximum cable size
Mains, motor, brake, and load share
2 2)
(mm /AWG )
Maximum external mains fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
Weight, enclosure, IP20/IP21/IP54, [kg (lbs)]
4)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Power card ambient trip [°C (°F)]
*High overload=150% current for 60 s, Normal overload=110% current for 60 s.
Table 8.3 Technical Specifications, D2h/D4h, Mains Supply 3x525–690 V AC
1) For type of fuse, consult the operating instructions.
2) American Wire Gauge.
3) The typical power loss is at normal conditions and expected to be within
These values are based on a typical motor efficiency (IE2/IE3 border line). Lower efficiency motors add to the power loss in the frequency converter
and the opposite is also true. Applies to dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting,
the power losses may increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer
to www.danfoss.com/vltenergyefficiency. Further options and customer load can add up to 30 W to the losses (though typically only 4 W extra for
a fully loaded control card or options for slot A or slot B, each).
4) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency.
Efficiency measured at nominal current. For energy efficiency class, see chapter 8.4.1 Ambient Conditions. For part load losses, see
www.danfoss.com/vltenergyefficiency.
Enclosure size
D5h
D6h
D7h
D8h
Table 8.4 D5h–D8h Weight
64
®
VLT AQUA Drive FC 202
N200
HO NO
132 160
200 250
160 200
201 253
302 278
192 242
288 266
191 241
191 241
229 289
198 245
189 234
197 240
3) 2361 3074
2446 3175
3)
Description
D1h ratings+disconnect and/or brake chopper
D1h ratings+contactor and/or circuit breaker
D2h ratings+disconnect and/or brake chopper
D2h ratings+contactor and/or circuit breaker
Danfoss A/S © 11/2016 All rights reserved.
N250 N315
HO NO HO
160 200 200
250 300 300
200 250 250
D4h
D2h
253 303 303
380 333 455
242 290 290
363 319 435
241 289 289
241 289 289
289 347 347
245 299 299
234 286 286
240 296 296
2x185 (2x350 mcm)
550
3012 3723 3642
3123 3851 3771
125 [275]
0.98
0–590
110 (230)
80 (176)
± 15% (tolerance relates to variety in voltage and cable conditions.)
Maximum weight, [kg (lbs)]
166 (255)
129 (285)
200 (440)
225 (496)
P400
NO HO NO
250 250 315
350 350 400
315 315 400
360 360 418
396 540 460
344 344 400
378 516 440
343 343 398
343 343 398
411 411 478
355 355 408
339 339 390
352 352 400
4465 4146 5028
4614 4258 5155
0–525
MG21A402