Page 3
INSTALLING THE STAGE REAR WINDOW (I) In this assembly session you will attach the rear window and its chrome frame. Please follow our instructions and the accompanying illustrations carefully. PIECES FOR THIS STAGE 66 A Rear window 66 B Rear window frame 66 C Double-sided tape REAR WINDOW These items are not toys;...
Page 4
STAGE 66 66.1 two strips of double-sided tape 66C from the emove backing paper and stick them on the inside of the top edge of the chrome frame 66B, as shown in the illustration.
Page 5
STAGE 66 66.2 emove another two strips of double-sided tape and stick them on the inside of the lower edge of the rear window frame 66B. 66.3 sing a paiR of tweezeRs remove the protective film from all the strips of double-sided tape you attached to the frame 66C.
Page 6
STAGE 66 66.4 attach the rear window 66A to the inside of the frame 66B. Press the pieces together for a few seconds to secure them firmly. STAGE 66 FINAL RESULT You have now attached the chrome frame to the rear window. Put what you have built so far in a safe place until you are ready to install it on your model.
Page 7
INSTALLING THE STAGE WINDSCREEN (I) In this assembly session you will attach the strips of double-sided tape needed to attach the frame to the windscreen. Please follow our instructions and the accompanying illustrations carefully. PIECES FOR THIS STAGE 67 A Windscreen 67 C Double-sided tape type 1 67 E Double-sided tape type 3 67 B Windscreen frame...
STAGE 67 67.1 emove three strips of type 1 double-sided tape 67C from the backing paper, and attach them in a row on the inside of the lower edge of the windscreen frame 67B. ASSEMBLY TIP Use this illustration to help you identify the correct position for the different types of double-sided tape.
Page 9
STAGE 67 67.2 ow attach three strips of type 2 double-sided tape 67D to the inside of the top edge of the windscreen frame 67B. 67.3 ttach two strips of type 3 double-sided tape 67E to the inside of the left edge of the windscreen frame 67B.
Page 10
STAGE 67 67.4 ttach another two strips of type 3 double-sided tape 67E to the inside of the right edge of the windscreen frame 67B. Note: do not remove the protective film from the strips of double-sided tape you have attached to the windscreen frame. You will remove them in another assembly session.
Page 11
INSTALLING THE STAGE REAR QUARTER WINDOWS (I) In this assembly session you will start installing the rear left quarter window. Please follow our instructions and the accompanying illustrations carefully. PIECES FOR THIS STAGE 68 A Chrome profile 1 for the rear left quarter 68 C Chrome profile 2 for the rear left quarter window window...
Page 12
STAGE 68 68.1 the linchpins on the chrome profile 2 68C as shown in osition the illustration. Attach the piece to the black strip on the outside of the rear left quarter glass 68B. 68.2 the rear left quarter glass 68B into its housing on the left side of the middle section of the car body 61A.
Page 13
STAGE 68 68.3 taRt securing the piece to the car body section 61A by inserting – from the inside – two type MP screws into the holes in the front of the rear left quarter glass 68B. A USEFUL TIP Sometimes you may find that you have left unsightly fingerprints on the pieces you have handled.
Page 14
STAGE 68 68.4 nseRt another type MP screw into the hole indicated in the illustration. STAGE 68 FINAL RESULT You have now finished the first stage of installing the rear left quarter window on the car body.
Page 15
INSTALLING THE STAGE REAR QUARTER WINDOWS (II) In this assembly session you will start installing the rear right quarter window. Please follow our instructions and the accompanying illustrations carefully. PIECES FOR THIS STAGE 69 A Chrome profile 1 for the rear right quarter 69 B Rear right quarter glass 69 C Chrome profile 2 for the rear right quarter window...
Page 16
STAGE 69 69.1 the linchpins on the chrome profile 2 69C as osition shown in the illustration. Attach the piece to the black strip on the outside of the rear right quarter glass 69B. 69.2 the rear left quarter glass 69B into its housing on the right side of the middle section of the car body 61A.
Page 17
STAGE 69 69.3 taRt attaching the piece to the car body section 61A by inserting – from the inside – two type MP screws into the holes in the front of the rear right quarter glass 69B. USEFUL TIP When assembling the body parts, you need to take some precautions to protect the paint and avoid any scratches.
Page 18
STAGE 69 69.4 nseRt another type MP screw into the hole indicated in the illustration. STAGE 69 FINAL RESULT You have now finished the first stage of installing the rear right quarter window on the car body.
Page 19
ATTACHING STAGE THE ROOF In this assembly session you will attach the roof of you model car. Please follow our instructions and the accompanying illustrations carefully. PIECES FOR THIS STAGE 70 Roof NP screws 1.2X3.5 mm (x 5)* 70 B Double-sided tape OP screws 1.5X3 mm (x 5)* LM screws 2.3X4 mm (x 12)* RM flat head screws 1.7X3.5 mm (x 3)*...
Page 20
STAGE 70 70.1 the rear window and the windscreen that you prepared in the previous assembly sessions. Place the piece composed of the rear window 66A and its frame 66B onto the rear opening in the middle section of the car body 61A, and put the windscreen 67A on the front.
Page 21
STAGE 70 70.4 70.5 four type LM screws into the corresponding one strip of double-sided tape 70B nseRt emove holes in the roof 70A and the middle section of the from the backing paper and attach it to the car body 61A. straight end of the chrome frame 1 of the rear left quarter window 68A.
Page 22
STAGE 70 70.8 emove the protective film from the strip of double-sided tape on the frame 69A. Position it in the same way you did on the other side, and insert a type RM screw into the hole in the front. 70.9 two type OP screws and two type NP screws to secure the piece from the inside.
Need help?
Do you have a question about the MODEL SPACE FAST & FURIOUS DODGE CHARGER R/T and is the answer not in the manual?
Questions and answers