Table of Contents
Advertisement
TECHNICAL SPECIFICATIONS
Technology:
Detection mode:
Max. detection range:
Remission factor:
Angular resolution:
Emission characteristics
IR laser:
Red visible laser:
Supply voltage:
Power consumption:
Peak current @ power-on:
Cable length:
Response time
Motion detection:
Presence detection:
Output:
Max. switching voltage:
Max. switching current:
Switching time:
Output resistance:
Voltage drop on output:
Leakage current:
Input:
Max. contact voltage:
Voltage threshold:
LED signal:
Dimensions:
Material:
Color:
Mounting angles on bracket:
Rotation angles on bracket:
Tilt angles on bracket:
Protection degree:
Temperature range:
Humidity:
Vibrations:
Pollution on front screen:
Norm conformity:
BEA, the sensor manufacturer, cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device;
therefore, BEA does not guarantee any use of the sensor outside of its intended purpose.
BEA strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/
gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring
that the sensor system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer
recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must
be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.
ANSI/DASMA 102, ANSI/DASMA 107, UL 325).
Verify that all appropriate industry signage and warning labels are in place.
BEA hereby declares that the LZR
2006/95/EC, 2002/95/EC, 2004/108/EC and 2006/42/EC.
Notified Body for EC inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, 45141 D-Essen
EC-type examination certificate number: 44 205 11 392410-002
Angleur, May 2011
The complete declaration of conformity is available on our website: www.bea-industrial.be
For EC countries: according to the directive 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: Tech_Services@beainc.com | Tech Docs: www.BEAinc.com
Page 12 of 12
Page 12 of 12
laser scanner, time-of-flight measurement
motion and presence
5.0 m x 6.5 m (16 ft 6 in x 21 ft)
> 2%
0,3516°
wavelength 905 nm; max. output pulse power 75 W (CLASS 1)
wavelength 650 nm; max. output CW power 3 mW (CLASS 3R)
10 – 35 VDC @ sensor side
< 5 W
1.8 A (max. 80 ms @ 35 V)
10 m (30 ft)
typ. 200 ms (adjustable)
typ. 20 ms (max. 80 ms)
2 electronic relays (galvanic-isolated – polarity-free)
35 VDC / 24 VAC
80 mA (resistive)
t
=5 ms; t
=5 ms
ON
OFF
typ 30 Ω
< 0.7 V @ 20 mA
< 10 µA
1 optocoupler (galvanic-isolated – polarity-free)
30 VDC (over-voltage protected)
Log. H: >8 VDC
Log. L: <3 VDC
1 blue LED: power-on status
2 bi-coloured LEDs: detection/output status (green = no detection, red = detection)
5.0 in (D) x 3.6 in (W) x 2.75 in (H) (mounting bracket + 0.55 in)
PC/ASA
Black
-45°, 0°, 45°
-5 – 5 ° (lockable)
-3 – 3 °
IP65
-30 – 60 °C if powered
0 – 95% non-condensing
< 2G
max. 30%, homogenous
2006/95/EC: LVD
2002/95/EC: RoHS
BEA INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
®
-I100/-I110 is in conformity with the basic requirements and the other relevant provisions of the directives
Jean-Pierre Valkenberg, Authorized representative and responsible for technical documentation
1 orange LED: error status
-10 – 60 °C if unpowered
2004/108/EC: EMC
IEC 60825-1:2007
EN 60529:2001
EN 60950-1:2005
EN 61000-6-2:2005
EN 61000-6-3:2006
75.5897.02 LZR-H110 20170821
75.5897.02 LZR-H110 20170821
Advertisement
Table of Contents
