Table of Contents
Related Manuals for BEA LZR-I30
Summary of Contents for BEA LZR-I30
- Page 1 -I30 LASER SCANNER FOR INDUSTRIAL DOORS with max. detection range of 30 ft x 30 ft User’s Guide Visit website for available languages of this document. 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 1 of 12 Page 1 of 12...
-
Page 2: Installation And Maintenance
35 °F. Page 2 of 12 Page 2 of 12 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125... -
Page 3: Led Signal
This can be useful in cases where the sensor should not draw any attention. SYMBOLS Possible remote Remote control Caution! control sequence Laser radiation adjustments Factory values Alarm Quick installation 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 3 of 12 Page 3 of 12... -
Page 4: How To Use The Remote Control
30 minutes after last use, the sensor locks access to the remote control session. To regain access, cycle the power. The remote control session will then be accessible for another 30 minutes. 30’ Page 4 of 12 Page 4 of 12 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125... - Page 5 Relay 2: Safety Field Green/White CONNECTOR Blue (+) Test Blue/White (-) Orange No test function: Learn Orange/Black connect blue and blue/white wires to power supply (no polarity) 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 5 of 12 Page 5 of 12...
- Page 6 Both red LEDs flash slowly and the 3 visible laser beams automatically illuminate during 30 seconds. learn After setting the mounting side, the safety and the optional field have the same dimensions. Page 6 of 12 Page 6 of 12 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125...
- Page 7 The default field dimension is limited to 200 in x 200 in. You can adapt the dimensions by remote control, but those dimensions cannot be larger than the shape defined by the learn. 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 7 of 12...
- Page 8 360 in 200 in See page 9 to change output configuration to suitable applications. IMPORTANT: Test the proper operation of the installation before leaving the premises. Page 8 of 12 Page 8 of 12 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125...
- Page 9 NO = normally open P – NC A – NO P – NC A – NO R2 Safety field NC = normally closed R = relay output 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 9 of 12 Page 9 of 12...
-
Page 10: Troubleshooting
No code is required to unlock during the an incorrect code was used first minute after powering. Can’t find your answer? Visit www.beainc.com or scan QR code for Frequently Asked Questions! Page 10 of 12 Page 10 of 12 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125... -
Page 11: Technical Specifications
EN 12453:2000 chapter 5.1.1.6, chapter 5.5.1 Safety device E EN ISO 13849-1:2008 CAT2, PI «d» EN 61496-3:2008 ESPE Type 2 Specifications are subject to change without prior notice. All values measured in specific conditions. 75.5667.11 LZR-I30 20191125 75.5667.11 LZR-I30 20191125 Page 11 of 12 Page 11 of 12... - Page 12 BEA, Inc. does not guarantee any use of the sensor outside of its intended purpose. BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-trained for the type of door/gate system.