Related Manuals for BEA 10LZRI30
Summary of Contents for BEA 10LZRI30
- Page 1 ® -I30 LASER SCANNER FOR INDUSTRIAL DOORS with max. detection range of 30 ft x 30 ft User’s Guide Visit website for available languages of this document. 75.5667.12 LZR-I30 20230411 Page 1 of 12...
-
Page 2: Installation And Maintenance
READ BEFORE BEGINNING INSTALLATION/PROGRAMMING/SET-UP SAFETY The device emits invisible (IR) and visible laser radiation. IR laser: wavelength 905nm; output power 0.10mW CLASS 1 LASER PRODUCT (Class 1 according to IEC 60825-1) Visible laser: wavelength 635nm; output power 0.95mW CLASS 2 LASER RADIATION (Class 2 according to IEC 60825-1) DURING INSTALLATION DO NOT STARE INTO BEAM... -
Page 3: Led Signal
READ BEFORE BEGINNING INSTALLATION/PROGRAMMING/SET-UP DESCRIPTION protection cover laser window – emission visible laser beams (3) laser window – reception notches for tilt angle adjustment (2) LED signals (4) adjustable bracket screws for position lock (2) cable conduits (4) connector LED SIGNAL 1. -
Page 4: How To Use The Remote Control
READ BEFORE BEGINNING INSTALLATION/PROGRAMMING/SET-UP HOW TO USE THE REMOTE CONTROL After unlocking, the red If the red LED flashes quickly after unlocking, you To end an adjustment session, LED flashes and the sensor need to enter an access code from 1 to 4 digits. always lock the sensor. - Page 5 MOUNTING 4 in 1 in 1 in 45° 45° Use the mounting template to Pass the cable ± 4 in through Position the bracket and secure position the sensor correctly. The the cable opening. If drilling an using the 4 screws to avoid gray area indicates the detection opening is not possible, use the vibrations.
- Page 6 POSITIONING Unlock the sensor and activate the visible laser beams in order to position the curtains parallel to the door. The visible laser beams stay activated for 15 minutes or can be turned off by the same sequence. Adjust the lateral position Adjust the tilt angle of the Lock the position of the mounting of the detection field.
- Page 7 SAFETY FIELD CONFIGURATION (RELAY 2) SAFETY FIELD LEARN Launch a learn after changing the sensor position or when new objects are added/changed in the detection zone. Either wait for the sensor to learn its environment or lock it by remote control. max.
- Page 8 OPTIONAL FIELD CONFIGURATION (RELAY 1) Make sure the white and green wires are connected to the corresponding inputs before configuring the optional field. VIRTUAL PUSH-BUTTON LEARN (VPB) Install 1 or 2 virtual push-buttons as activation zone(s) to open the door «manually». Apply the vitual push button sticker(s) within the optional field.
- Page 9 REMOTE CONTROL ADJUSTMENTS (OPTIONAL) ACTIVE DETECTION CURTAINS C1 + C2 are active on safety field CURTAIN C3 + C4 are active on optional field deactivate curtain on both fields C1 is active on both fields activate curtain only on optional field C2+C3 are active on safety field C4 is inactive activate curtain only on safety field...
-
Page 10: Troubleshooting
TROUBLESHOOTING No blue LED No power Check cable and connexion. Polarity of power supply is Check the polarity of the power supply. inverted All LEDs have been deactivated Activate LEDs using remote control. by remote control Only blue LED is on Test input is not connected Check wiring. -
Page 11: Technical Specifications
TECHNICAL SPECIFICATIONS Technology: laser scanner, time-of-flight measurement Detection mode: motion and presence Max. detection range: 30’ x 30’ Uncovered zone: 2 – 19“ (adjustable) Remission factor: > 2% Angular resolution: 0,3516° Min. detected object size (typ.): 0.8 in @ 118 in (in proportion to obj. - Page 12 BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose. BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/ gates, and factory-trained for the type of door/gate system.