Savant REM-0300RF-00 Deployment Manual

Savant REM-0300RF-00 Deployment Manual

Button remote

Advertisement

Savant Button Remote
REM-0300RF-00
Deployment Guide
Document Number:
009-1624-00
Document Date:
May 2018
Document Supports:
da Vinci 8.8
Savant Button Remote Deployment Guide
009-1624-00 | 180521
1
of
14
Copyright © 2018 Savant System, LLC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the REM-0300RF-00 and is the answer not in the manual?

Questions and answers

Summary of Contents for Savant REM-0300RF-00

  • Page 1 Savant Button Remote REM-0300RF-00 Deployment Guide Document Number: 009-1624-00 Document Date: May 2018 Document Supports: da Vinci 8.8 Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 2: Table Of Contents

    5.2 Adding a Controller to a Configuration ............8 5.3 Adding a Remote to a Configuration ............9 5.4 Custom Button Example ................. 10 Appendix A: Button Properties ..............13 Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 3 WEIGHT INJURY! exposed to rain or moisture, does not operate normally, or has been Installing some of the Savant equipment requires two installers to dropped. ensure safe handling during installation. Failure to use two installers 15.
  • Page 4: Introduction

    RacePoint Blueprint da Vinci 8.8 or higher 2 Deployment Steps Follow these steps to successfully deploy Savant Button Remote. This page can be used as a checklist to record which steps have been completed. 1. Review product specifications ..............................REM-0300RF Equipment Overview 2.
  • Page 5: Rem-0300Rf Equipment Overview

    3 REM-0300RF Equipment Overview Refer to the Quick Reference Guide for these products located on the Savant Customer Community for Box Contents and Specifications. 3.1 Controller Front Panel Press will place the device in remote pairing mode, this will turn the Status LED red.
  • Page 6: Remote

    Place the two AA batteries. Position the cover and slide up to secure the battery latch. The UID can be found inside the Battery cover of the Remote. Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 7: Installation

    4 Installation The Savant Button Remote requires the use of a Controller to allow the commands to be sent to the Host. This section covers the installation of the Controller. 4.1 Controller The Controller must be installed within the RF range of the Remote. Savant recommends that the Controller is installed in the same room the Remote is going to be used in.
  • Page 8: Blueprint Configuration

    In the Search bar type W103I. Select the Controller. Open Inspector. Enter the UID. Select the Controller that is needed and drag it into a Shared Equipment zone. Name the Device. Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 9: Adding A Remote To A Configuration

    Select the Remote that is needed and drag it into the User zone where it will be used. Name the Device. NOTE: The UID of the Remote can be found inside the Battery Cover. Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 10: Custom Button Example

    NOTE: If there is more than one Remote in the configuration they will all be listed here. They must be programmed one at a time. 3. Select a Button * (Left). HELPFUL INFO: As shown in the image above Savant Scene is checked by default. This feature is configured by the User in the Savant Pro App. For more information please see Adding a Scene to a Button Application Note on the Savant Customer Community.
  • Page 11 4. Uncheck the Savant Scene checkbox. 5. Select the Zone. 6. Select the Service. 7. Set Press Command. 8. Set Toggle Press Command. 9. Open the SRS window. Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 12 10. Select Service 11. Select the Cable TV service. 12. Select States. 13. Click and Drag ServiceIsActive to the Toggle State. 14. Click Apply. Savant Button Remote Deployment Guide Copyright © 2018 Savant System, LLC 009-1624-00 | 180521...
  • Page 13: Appendix A: Button Properties

    Appendix A: Button Properties Title Label for the button and can’t be modified – Box Checked: Configured in the Savant Pro App to activate a Savant App Scene. Savant Scene – Box Unchecked: Allows programming of commands onto the button.
  • Page 14 Savant Systems, LLC. shall not be liable for any technical or editorial errors or omissions contained herein or for incidental or consequential damages resulting from the performance, furnishing, reliance on, or use of this material.

Table of Contents