Before You Begin What is included LEG-5000, Legend™ 5000X Power cord with plug 9 additional metal gobos HMI575 Discharge lamp Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling.
NTRODUCTION Control Features Legend™ 5000X (575W) • Mechanical dimmer (0~100%) • Variable shutter/strobe (7fps) • Color wheel - 11 colors plus open - Rainbow color spin - in both directions - at variable speeds • Second color wheel - 11 colors plus open - 1 CT filter, 4 solid, 4 split-colors &...
Product Overview DMX signal indicator UTTONS MENU◄ Toggles Menu Functions MENU► Toggles Menu Functions Steps backwards through SELECT▼ selections or addressing Steps forward through SELECT▲ selections or addressing LEG-5000X User Manual SEGMENT BUTTONS I/O PANEL OVERVIEW I/O P ANEL DMX Out & In DMX-512 connectors Power AC input IEC 60320 C14 and fuse holder...
ETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A HMI575 high intensity discharge lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement.
Power Your product is equipped with an internal input-voltage select switch. Warning! Verify that the power select switch on your unit matches the line voltage applied. All fixtures must be connected to circuits with a suitable Earth Ground. • To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart.
Replacing Gobos 1. Unscrew thumbscrews (S1) to detach the top cover. 2. Remove screws labeled (S2) and pull out air channel guide (A1) to allow more space for the replacement of gobos. 3. Rotate the gobo wheel so that the gobo to be replaced lies in the center of the “U”...
All models described include 2 clamp mounting brackets to which a half-coupler pipe clamp can be bolted. 1. Verify the structure can hold 10 times the weight of all fixtures to-be installed. 2. Attach two clamps as illustrated above (b). LEG-5000 User Manual Introduction a. Clamp brackets b. Clamps c.
PERATING NSTRUCTIONS Control Board On the control panel you can set the DMX address, reset the fixture and change fixture personality trait. [SELECT] Changes menu function status and is used to set DMX address. Control Board Functions UNCTION PTIONS Addr 000~512 DMX channel addressing LP.ti Shut...
DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate the start address selected for future reference. LEG-5000 User Manual Operating Instructions Daisy Chain Connection...
{ C H nl } – Pa n /T i lt co nt ro l channel re-assign This function will re-position the pan & tilt control channels to start at DMX value number 1. UNCTION CHnl LEG-5000 User Manual OTES 8 bit Control Channel 16 bit Control Channel...
{ t u rn } - R e ve r se t he d i sp l a y You can rotate the display 180° so that it becomes easier to read when the fixture is positioned upside down. UNCTION turn LEG-5000 User Manual OTES Normal Shutter auto-close OTES...
UNCTION dEMo { S o Ft } – De mo sp ee d You can set the pace of the demo to either quick or fast. UNCTION SoFt LEG-5000 User Manual OTES Normal Reset all motors OTES Normal Reset unit...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
DMX Channel Values 16 Bit Movement HANNEL ALUE LEG-5000X User Manual UNCTION Dimmer Closed > Open (0-100%) Shutter/Strobe Blackout Open Strobe: Slow > Fast (max 7fps) Open Pulse Strobe: Dark > Bright & Slow > Fast Open Pulse Strobe: Bright > Dark & Slow > Fast Open Random Strobe: Slow >...
You should clean this filter every two weeks or sooner if necessary depending on your particular environment. LEG-5000 User Manual OTES This is the default setting on the fixture and helps in reducing...
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cau for the return.
Remote does not work Make sure connector is firmly connected to device Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions do not require additional settings, simply power the fixture and it will automatically enter into this mode Unit wobbles when...