Before You Begin What is included LEG-3000, Legend™ 3000X or 9 additional metal gobos Power cord with plug HSD250 Discharge lamp Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
Toggles Menu Functions Steps backwards through SELECT▼ selections or addressing Steps forward through SELECT▲ selections or addressing LEG-3000 Manual See Appendix Section; Dip Switches (settings explained) SEGMENT BUTTONS I/O PANEL OVERVIEW I/O P ANEL DMX Out & In DMX-512 connectors...
Navigate to the {LPti} on the menu display to obtain this information. (Page 11, Control Board Functions) 8. Replace lamp top cover and fasten with screws. LEG-3000 Manual Revision: 2006-01-20/16:03...
5. Move the frequency switch to the setting that matches the local AC frequency; 50 or 60 Hz. 6. Replace access cover. Pow e r Ca bl e Conf igu ra t io n ABLE ROWN ELLOW REEN LEG-3000 Manual Input Voltage Switch NTERNATIONAL Live Neutral Earth EG (Ground)
However, the spring needs to be removed first using a small flat head screw driver before pushing the gobo out of the aperture. LEG-3000 Manual Cover removed Gobo tension ring Revision: 2006-01-20/16:03...
All models described include 2 clamp mounting brackets to which a half-coupler pipe clamp can be bolted. 1. Verify the structure can hold 10 times the weight of all fixtures to-be installed. 2. Attach two clamps as illustrated above (b). LEG-3000 Manual a. Clamp brackets b. Clamps c. Safety cable channel d.
Off/On Off/On LEG-3000 Manual Lamp use timer Pressing ▲▼ simultaneously zeroes lamp counter. Off: Normal On: Shutter closes during the changing of color, gobos or prism. Shutter will open after color, gobo or prism is in position.
(male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. LEG-3000 Manual Daisy Chain Connection...
You can apply a pan and tilt Invert by following the settings in the table below. UNCTION LEG-3000 Manual OTES 8 bit Control Channel 16 bit Control Channel OTES...
{ } - R ev e r se t h e dis pl a y You can rotate the display 180° so that it becomes easier to read when the fixture is positioned upside down. UNCTION LEG-3000 Manual OTES Default Pan/Tilt re-assign to channel OTES...
{ } – F i xt u re T im er The (Fixture Timer) readout displays the total number of operating hours of the fixture. It is not uncommon to find new fixtures with a few logged hours. LEG-3000 Manual OTES Normal...
Legend 3000X: DMX address Ch 015, Aud.S or Aud.F set to OFF Important! All Slave fixtures must have “Aud.S” or “Aud.F” set to off. You must set “Aud.S” and “Aud.F” to off to regain DMX control of the fixture. LEG-3000 Manual OTES Normal Run self-demonstration...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Only the lamp will turn on in the fixture. 1-On, 2-On Only the lamp will turn on in the fixture 3-On This switch will terminate the dmx connection. LEG-3000 Manual Tilt Down (0°) > Up (270°) (128 = half way point) Pan (Fine) Tilt (Fine)
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
Remote does not work Make sure connector is firmly connected to device Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions do not require additional settings, simply power the fixture and it will automatically enter into this mode Unit wobbles when...